When large amount of memory, about 1TB, is removed with DLPAR memory
remove operation, kdump reload could fail due to race condition with
device tree property update. In such scenario, the subsequent kdump
reload requests would also fail as reload() only proceeds if current
load status is active. Since the possibility of this race condition
couldn't be wished away due to the nature of the scenario, workaround
it by proceeding to load even if current load status is not active as
long as kdump service is active, which kdump udev rules already check
for.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Acked-by: Kairui Song <kasong@redhat.com>
In kdump.conf, if sshkey points to an invalid ssh key, 'kdumpctl restart'
can bail out immediately instead of retry.
Signed-off-by: Pingfan Liu <piliu@redhat.com>
Acked-by: Kairui Song <kasong@redhat.com>
Print some message during the long wait period to reflect the process.
The message will look like:
Network dump target is not usable, waiting for it to be ready
...
Signed-off-by: Pingfan Liu <piliu@redhat.com>
Acked-by: Kairui Song <kasong@redhat.com>
On a host with ipaddr not ready before kdump service, ssh return errno 255.
While if no ssh-key, ssh also return errno 255. For both of cases, the
current kdump code promote user to run 'kdumpctl propagate'. This confuses
user who already installs ssh-key.
In order to tell these two cases from each other, the ssh warning message
should be involved, and parsed.
For the no ssh-key case , warning message is "Permission denied" or "No
such file or directory". For the other, warning message is "Network
Unreachable"
This patch also does a slight change to enlarge the timeout from 60s to
180s. This value can meet test at the time being
Signed-off-by: Pingfan Liu <piliu@redhat.com>
Acked-by: Kairui Song <kasong@redhat.com>
If dump target is ipv6 address, a host should have ipv6 address ready
before starting kdump service. Otherwise, kdump service fails to start due
to the failure "ssh dump_server_ip mkdir -p $SAVE_PATH".
And user can see message like:
"Could not create root@2620:52:0:10da:46a8:42ff:fe23:3272/var/crash"
I observe a long period (about 30s) on some machine before they got ipv6
address dynamiclly, which is never seen on ipv4 host.
Hence kdump service has a dependency on ipv6 address. But there is no good
way to resolve it. One way is asking user to run the cmd "nmcli connection
modify eth0 ipv6.may-fail false". But this will block systemd until ipv6
address is ready. Despite doing so, kdump can try its best (wait 1 minutes
after it starts up) before failure.
How to implement the wait is arguable. It will involve too many technique
details if explicitly waiting on ipv6 address, instead, just lean on 'ssh'
return value to see the availability of network.
Signed-off-by: Pingfan Liu <piliu@redhat.com>
Acked-by: Kairui Song <kasong@redhat.com>
Currently kdumpctl rebuild will simply rebuild the initramfs, and
only perform basic config syntax check. But it should also check if the
target path is available when using SSH target, else kdump may fail.
is second kernel. kdumpctl rebuild should cover this case, and create
the path if it doesn't exist.
This patch make rebuild and restart behaves the same, rebuild is
now equal to restart, except it won't check config change or reload
kdump resource.
Signed-off-by: Kairui Song <kasong@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Although "kdumpctl rebuild" is introduced to help user rebuild the
initramfs without modifying the kdump.conf, if the kdump.conf is
modified and "kdumpctl rebuild" is called, a initramfs with a faulty
kdump.conf will be built.
Kdump will refuse to load the initramfs when restarted, but kdumpctl
reload may load the faulty initramfs. So need to make sure the faulty
build won't be generate in the first place.
Check for kdump.conf error before building the initramfs to ensure such
failure won't happen.
Signed-off-by: Kairui Song <kasong@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
We don't necessarily have to always rebuild the initramfs when
extra_modules is set. Instead, just detect if any module is updated,
and only rebuild initramfs if found any updated kernel module.
Tested with in-tree kernel modules, out-of-tree kernel modules, weak
modules, all worked as expected.
Signed-off-by: Kairui Song <kasong@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Previously only the symlink's timestamp is used for checking if file are
modified, this will not trigger a rebuild if the symlink target it
modified.
So check both symlink timestamp and symlink target timestamp, rebuild
the initramfs on both symlink changed and target changed.
Also give a proper error message if the file doesn't exist.
Signed-off-by: Kairui Song <kasong@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
When reading kdump configs, a single parsing should be enough and this
saves a lot of duplicated striping call which speed up the total load
speed.
Speed up about 2 second when building and 0.1 second for reload in my
tests.
Signed-off-by: Kairui Song <kasong@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Early kdump inherits the settings of normal kdump, so any changes that
caused normal kdump rebuilding also require rebuilding the system initramfs
to make sure that the changes take effect for early kdump.
Therefore, when the early kdump is enabled, provide a prompt message after
the rebuilding of kdump initramfs is completed.
Signed-off-by: Lianbo Jiang <lijiang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Previous we rebuild the initramfs when kenrel load module list changed,
but this is not very stable as some async services may load/unload
kernel modules, and cause unnecessary initramfs rebuild.
Instead, it's better to just check if the module required to dump to
the dump target is loaded or not, and rebuild if not loaded. This
avoids most false-positives, and ensure local target change is always
covered.
Currently only local fs dump target is covered, because this check
requires the dump target to be mounted when building the initramfs,
this guarantee that the module is in the loaded kernel module list,
else we may still get some false positive.
dracut-install could be leveraged to combine the modalias list with
kernel loaded module list as a more stable module list in the initramfs,
but upstream dracut change need to be done first.
Passed test on a KVM VM, changing the storage between SATA/USB/VirtIO
will trigger initramfs rebuild and didn't notice any false-positive.
Also passed test on my laptop with no false-positive.
Signed-off-by: Kairui Song <kasong@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
This reverts commit 6b479b6572.
Check initramfs rebuild by looking at if there is any change of load
kernel modules list is not very stable after all. Previously we are
counting on udev to settle before kdump is started to ensure all modules
is ready, but actually any service may cause a kernel module load, even
after udev is settled.
The previous commit is trying to workaround an issue that VM created
with disk snapshot may fail in the kdump initramfs. The better fix is to
not include the kdump initramfs in the disk snapshot at all, as the
kdump initramfs is not generated for a generic use. And With new added
"kdumpctl reload" command, admins could rebuild the image easily, and
should rebuild the initramfs on hardware change manually.
Signed-off-by: Kairui Song <kasong@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Use "kdumpctl rebuild" to rebuild the image directly. This could help
admins to rebuild kdump image directly.
Also merge fadump related initramfs backup/restore into setup_initrd,
and do permission only when actually trying to rebuild the image.
Signed-off-by: Kairui Song <kasong@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
With kernel commit 0823c68b054b ("powerpc/fadump: re-register firmware-
assisted dump if already registered") support is enabled to re-register
when FADump is alredy registered. Leverage that option in kdump scripts.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Acked-by: Kairui Song <kasong@redhat.com>
The idea behind adding support for dracut '--rebuild' option was to
ensure the initrd built for fadump takes into consideration all the
build parameters passed to original initrd. Pass original initrd
instead of current default initrd for rebuild as current initrd
might already have build parameters from original initrd along
with parameters from previous fadump intird build making the
build parameters look like this after a few iterations:
-H --persistent-policy 'by-uuid' -f --quiet --hostonly --hostonly-
cmdline --hostonly-i18n --hostonly-mode 'strict' -o 'plymouth dash
resume ifcfg' --mount '/dev/mapper/rhel_zzfp219--lp3-home /kdumproot
//home xfs defaults' -f --kver '4.18.0-60.el8.ppc64le' --quiet
--hostonly --hostonly-cmdline --hostonly-i18n --hostonly-mode 'strict'
-o 'plymouth dash resume ifcfg' --mount '/dev/mapper/rhel_zzfp219--lp3-home
/kdumproot//home xfs defaults' -f --kver '4.18.0-60.el8.ppc64le' --quiet
--hostonly --hostonly-cmdline --hostonly-i18n --hostonly-mode 'strict'
-o 'plymouth dash resume ifcfg' --mount '/dev/mapper/rhel_zzfp219--lp3-home
/kdumproot//home xfs defaults' -f --kver '4.18.0-60.el8.ppc64le' --include
'/tmp/fadump.initramfs' '/etc/fadump.initramfs' --include
'/tmp/fadump.initramfs' '/etc/fadump.initramfs' --include
'/tmp/fadump.initramfs' '/etc/fadump.initramfs'
--
Since it is not desirable to build initrd with stale and/or duplicate
build parameters, use original initrd (backed up) to rebuild fadump
initrd, instead of current default initrd.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
If a crash occurs repeatedly after enabling kdump, the system goes
into a crash loop and the dump target may get filled up by vmcores.
This is likely especially with early kdump.
This patch introduces 'final_action' option to kdump.conf, in order
for users to be able to power off the system even after capturing
a vmcore successfully.
Signed-off-by: Kazuhito Hagio <k-hagio@ab.jp.nec.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Lianbo Jiang <lijiang@redhat.com>
Cc: Bhupesh Sharma <bhsharma@redhat.com>
Acked-by: Bhupesh Sharma <bhsharma@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Kairui Song <kasong@redhat.com>
In preparation for adding 'final_action' option, since it's confusing
to have the 'final_action' and 'default' options at the same time,
this patch introduces 'failure_action' as an alias of the 'default'
option to /etc/kdump.conf, and makes 'default' obsolete to be removed
in the future.
Also, the "default action" term is renamed to "failure action".
Signed-off-by: Kazuhito Hagio <k-hagio@ab.jp.nec.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Lianbo Jiang <lijiang@redhat.com>
Cc: Bhupesh Sharma <bhsharma@redhat.com>
Acked-by: Bhupesh Sharma <bhsharma@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Kairui Song <kasong@redhat.com>
In commit b34ce3a reload support was added to kdumpctl but the usage
info is not updated. Now add reload to usage output to let user aware
of the new command.
Signed-off-by: Kairui Song <kasong@redhat.com>
Add reload support to kdumpctl, reload will simply unload current
loaded kexec crash kernel and initramfs, and load it again.
Changes in /etc/sysconfig/kdump will take effect with kdumpctl
reload, but reloading will not check the content of
/etc/kdump.conf and won't rebuild anything. reload is fast, the only
time-consuming part of kdumpctl reload is loading kernel and initramfs
with kexec which is always necessary.
Signed-off-by: Kairui Song <kasong@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Currently the kdumpctl script doesn't check if the raw device is
formatted which might destroy existing data at the time of dump
capture.
This patch addresses this issue, by ensuring kdumpctl prints
a warning in case it finds the raw device to be formatted.
Signed-off-by: Kenneth D'souza <kdsouza@redhat.com>
Acked-by: Kairui Song <kasong@redhat.com>
Currently the kdumpctl script doesn't check if the path option is
set more than once due to which a vmcore is not captured.
This patch addresses this issue by ensuring that only one path
is specified in /etc/kdump.conf file.
Signed-off-by: Kenneth D'souza <kdsouza@redhat.com>
Acked-by: Kairui Song <kasong@redhat.com>
Currently, we only rebuilt kdump initramfs on config file change,
fs change, or watchdog related change. This will not cover the case
that hardware changed but fs layout and other configurations still
stays the same, and kdump may fail.
To cover such case, we can detect and compare loaded kernel modules,
if a hardware change requires the image to be rebuilt, loaded kernel
modules must have changed.
Starting from commit 7047294 dracut will record loaded kernel modules
when the image is built if hostonly mode is enabled. With this patch,
kdumpctl will compare the recorded value with currently loaded kernel
modules, and rebuild the image on change.
"kdumpctl start" will be a bit slower, as we have to call lsinitrd one
more time to get the loaded kernel modules list. I measure the time
consumption and we have an overall 0.2s increased loading time.
Time consumption of command "kdumpctl restart":
Before:
real 0m0.587s
user 0m0.481s
sys 0m0.102s
After:
real 0m0.731s
user 0m0.591s
sys 0m0.133s
Time comsumption of command "kdumpctl restart" with image rebuild:
Before (force rebuild):
real 0m10.972s
user 0m8.966s
sys 0m1.318s
After (inserted ~100 new modules):
real 0m11.220s
user 0m9.387s
sys 0m1.337s
Signed-off-by: Kairui Song <kasong@redhat.com>
we move some common functions from kdumpctl to kdump-lib.sh, the
functions could be used in other modules, such as early kdump.
It has no bad effect.
Signed-off-by: Lianbo Jiang <lijiang@redhat.com>
Reviewed-by: Kazuhito Hagio <khagio@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
port from rhel, original patch is contributed by Minfei Huang:
Using /sys to determines crashkernel actual size is confusing since
there is no unit of measure.
Add a new command "kdumpctl showmem" to show the reserved memory kindly.
Signed-off-by: Pingfan Liu <piliu@redhat.com>
Signed-off-by: Minfei Huang <mhuang@redhat.com>
Acked-by: Bhupesh Sharma <bhsharma@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
When core_collector is changed, the kdump initramfs needs to
be rebuilt before it is loaded.
Signed-off-by: Lianbo Jiang <lijiang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
When using "dracut_args --mount" to specify dump target, e.g. nfs like:
path /
core_collector makedumpfile -d 31
dracut_args --mount "host:/path /var/crash nfs defaults"
kdump service should neither guarantees the correctness, nor relabels it.
For current code, since dracut_args dump targets are likely not mounted
so kdump service mistakenly relabel the rootfs, which is meanless and
takes very long time.
Signed-off-by: Pingfan Liu <piliu@redhat.com>
This reverts commit 2040103bd7.
Reason is it's based on the environment of 1st kernel where all
present devices could be active and initialized during bootup.
Then all pci devices will request irqs. While kdump only brings
up those devices which are necessary for vmcore dumping. So this
commit is not meaningful and helpless to very large extent. And
it will print out 'Warning' when calculated result is larger than
1 cpu, actually it's a false positive report most of the time.
So revert the commit, and can check the git history for later
reference.
[dyoung]: on some machine this warning message shows up but
later we found the irq numbers with and without nr_cpus=1 is
quite different so this need more investigation since
the formula is not accurate.
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Resolves: BZ1484945
https://bugzilla.redhat.com/show_bug.cgi?id=1484945
Currently the kdumpctl script doesn't handle
whitespaces (including TABs) which might be there before
an option name in the kdump.conf
This patch addresses this issue, by ensuring that the
kdumpctl errors out in case it finds any stray space(s)
or tab(s) before a option name.
Reported-by: Kenneth D'souza <kdsouza@redhat.com>
Signed-off-by: Bhupesh Sharma <bhsharma@redhat.com>
Acked-by: Pratyush Anand <panand@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
As default initrd is used for booting fadump capture kernel, it must be
rebuilt with dump capture capability when dump mode is fadump. Check if
default initrd is already fadump capable and rebuild, if necessary.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Reviewed-by: Xunlei Pang <xlpang@redhat.com>
Now with the help of "--hostonly-cmdline", dracut will generate
the needed cmdlines for the dump target, so we can avoid the
corresponding duplicate or unnecessary inheritage.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Currently, we kept "root=X" for the dump_to_rootfs case, this
patch consolidates to use "--mount" for all the kdump mounts.
One advantage of this way is that dracut can correctly mark root
(in case of dump_to_rootfs is specified) as the host device when
"--no-hostonly-default-device" is added in the following patch.
Changed the code style in passing, as shellcheck tool reported:
Use $(..) instead of deprecated `..`
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Make is_fadump_capable() a library function, as we will need
it in mkdumprd.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
This reverts commit cb38b32dfc.
We are going to add "--hostonly-cmdline" dracut argument in
the following patch.
With the help of "--hostonly-cmdline", dracut will generate
"rd.lvm.lv=X" for us, no need to implement here again.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
This reverts commit 54a5bcc4ee.
We are going to add "--no-hostonly-default-device" dracut argument
in the following patch.
With the help of "--no-hostonly-default-device", dracut only
adds the dump target as host devices, which naturally guarantees
only required dracut modules being selected.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
We met a problem on AMD machines, when using "nr_cpus=4" for
kdump, and crash happens on cpus other than cpu0, kdump kernel
will fail to boot and eventually reset.
After some debugging, we found that it stuck at the kernel path
do_boot_cpu()-> ... ->wakeup_secondary_cpu_via_init():
apic_icr_write(APIC_INT_LEVELTRIG|APIC_INT_ASSERT|APIC_DM_INIT,
phys_apicid);
that is, it stuck at sending INIT from AP to BP and reset, which
is actually what "disable_cpu_apicid=X" tries to solve. Printing
the value of @phys_apicid showed that it was the value of "apicid"
other that of "initial apicid" showed by /proc/cpuinfo.
As described in x86 specification:
"In MP systems, the local APIC ID is also used as a processor ID by the
BIOS and the operating system. Some processors permit software to modify
the APIC ID. However, the ability of software to modify the APIC ID is
processor model specific. Because of this, operating system software
should avoid writing to the local APIC ID register. The value returned by
bits 31-24 of the EBX register (when the CPUID instruction is executed with a
source operand value of 1 in the EAX register) is always the Initial APIC ID
(determined by the platform initialization). This is true even if software
has changed the value in the Local APIC ID register."
From kernel commit 151e0c7de("x86, apic, kexec: Add disable_cpu_apicid
kernel parameter"), we can see in generic_processor_info(), it uses
a)read_apic_id() and b)@apicid to compare with @disabled_cpu_apicid.
a)@apicid which is actually @phys_apicid above-mentioned is from the
following calltrace(on the problematic AMD machine):
generic_processor_info+0x37/0x300
acpi_register_lapic+0x30/0x90
acpi_parse_lapic+0x40/0x50
acpi_table_parse_entries_array+0x171/0x1de
acpi_boot_init+0xed/0x50f
The value of @apicid(from acpi MADT) is equal to the value of "apicid"
showed by /proc/cpuinfo as proved by our debug printk.
b)read_apic_id() gets the value from LAPIC ID register which is "apicid"
as well.
While the value of "initial apicid" is from cpuid instruction.
One example of "apicid" and "initial apicid" of cpu0 from /proc/cpuinfo
on AMD machine:
apicid : 32
initial apicid : 0
Therefore, we should assign /proc/cpuifo "apicid" to "disable_cpu_apicid=X".
We've never met such issue before, because we usually tested "nr_cpus=1",
and mostly on Intel machines, and "apicid" and "initial apicid" have the
same value in most cases on Intel machines.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Resolves: bz1451717
https://bugzilla.redhat.com/1451717
When there is no crypt related kdump target, we can safely
omit "crypt" dracut module, this can avoid the pop asking
disk password during kdump boot in some cases.
This patch introduces omit_dracut_modules() before calling
dracut, we can omit more modules to reduce initrd size in
the future.
We don't want to omit any module for fadump, thus we move
is_fadump_capable() into kdump-lib.sh as a helper to use.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Resolves: bz1451717
https://bugzilla.redhat.com/1451717
When there is any "rd.lvm.lv=X", "lvm" dracut module will
try to recognize all the lvm volumes which is unnecessary
and probably cause trouble for us.
See https://bugzilla.redhat.com/show_bug.cgi?id=1451717#c2
Remove all the rd.lvm.lv=X inherited from the kernel cmdline,
and generate the corresponding cmdline as needed for kdump.
Because prepare_cmdline() is only used by kdump, we don't need
to add any fadump judgement(also remove the existing judgement
in passing).
Currently, we don't handle "rd.lvm.vg=X", we can add it in
when there is some bug reported in the future.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Resolves: bz1451717
https://bugzilla.redhat.com/1451717
We need to know all the kdump targets including the dump
target and root in case of "dump_to_rootfs".
This is useful for us to do some extra work related to the
type of different targets.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Resolves: bz1451717
https://bugzilla.redhat.com/1451717
This patch improves get_block_dump_target as follows:
-Consider block device in the special "--dracut-args --mount ..."
in get_user_configured_dump_disk().
-Consider save path instead of root fs in get_block_dump_target(),
and move it into kdump-lib.sh because we will have another user
in the following patch.
-For nfs/ssh dumping, there is no need to check the root device.
-Move get_save_path into kdump-lib.sh.
After this patch, get_block_dump_target() can always return the
correct block dump target specified.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Description of problem
(https://bugzilla.redhat.com/show_bug.cgi?id=1465735):
Run `kdumpctl status` as normal user, get below error messages:
Another app is currently holding the kdump lock; waiting for it to exit...
flock: 9: Bad file descriptor
Another app is currently holding the kdump lock; waiting for it to exit...
flock: 9: Bad file descriptor
...
The bug is caused by behavior difference between bash
and sh (bash in posix).
In the function single_instance_lock in kdumpctl script,
there is
exec 9>/var/lock/kdump
which will fail in user mode. However, this fail will cause
script exiting under bash but not exiting under sh, causing
infinite loop because the flock will always fail.
According to the 16th item in
ftp://ftp.gnu.org/old-gnu/Manuals/bash-2.02/html_node/bashref_66.html
If a POSIX.2 special builtin returns an error status, a non-
interactive shell exits.
And according to
https://www.gnu.org/software/bash/manual/html_node/Special-Builtins.html
exec is one of the POSIX.2 special builtin's.
This patch fixes the bug by checking exec return value.
Fixes: 9fb2996d05 ("kdumpctl: change the shebang header to use /bin/bash")
Signed-off-by: Ziyue Yang <ziyang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Reviewed-by: Xunlei Pang <xlpang@redhat.com>
kdump should not send fence_kdump notifications to local host, because
the role of the falied node (i.e local host) is to send fence_kdump
notifications to other nodes to tell them I'm kdumping, tell to itself is
nonsense. And we have excluded hostname of local host but when one use ip
address we also need exclude it.
Signed-off-by: Pingfan Liu <piliu@redhat.com>
Reviewed-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
We met one issue that when changing softlink of "/usr/bin/sh"
to point to "ksh" instead of the default "bash", kdumpctl will
not work and go wrong.
kdumpctl is expected to run under bash like dracut, we should
change its shebang header from "#!/bin/sh" to "#!/bin/bash".
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
The "time kdumpctl start" command shows that strip_comments()
consumes lots of cpu time. By only calling it when necessary,
it saves us nearly half second.
Tested on my Fedora kvm machine.
Before this patch:
$ time kdumpctl start
kexec: loaded kdump kernel
Starting kdump: [OK]
real 0m1.849s
user 0m1.497s
sys 0m0.462s
After this patch:
$ time kdumpctl start
kexec: loaded kdump kernel
Starting kdump: [OK]
real 0m1.344s
user 0m1.195s
sys 0m0.195s
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Resolves: bz1449801
"cat $KDUMP_CONFIG_FILE|grep -v "^#"|while read ..." use pipes
to invoke subshells, as a result we met "the dreaded inaccessible
variables within a subshell problem" as described in the book
"Advanced Bash-Scripting Guide".
It cause regressions, so revert it.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
I found using "cat $KDUMP_CONFIG_FILE|grep -v "^#"|while read ..."
instead of "while read ... do ...; done < $KDUMP_CONFIG_FILE" will
make the script run faster, it saves us nearly half second.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Pratyush Anand <panand@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
We use faster "lsinitrd XXX -f usr/lib/dracut/build-parameter.txt"
instead of "lsinitrd XXX | grep "^Arguments:" | head -1", this can
save us around one second.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Pratyush Anand <panand@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Use the logic of dracut 04watchdog/module-setup.sh to check,
then we only need to compare the content of 00-watchdog.conf,
so we can save one operation of lsinitrd.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Pratyush Anand <panand@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
handle_mode_switch() can ensure the correct logic, so remove
the needless is_mode_switched(). This helps to save one slow
lsinitrd operation for each boot.
Improved backup_default_initrd() to judge DEFAULT_INITRD.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Pratyush Anand <panand@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Some cloud people complained that VM boot speed is slower than
Ubuntu and other distributions, after some debugging, we found
that one of the causes is kdump service starts too slow(7seconds
according to the test result on the test VM), actually there is
no "crashkernel=X" specified. Although kdump service is parallel,
it affects the speed more or less especially on VMs with few cpus,
which is unacceptable. It is even worse when kdump initramfs is
built out in case of no reserved memory at first boot.
Commit afa4a35d3 ("kdumpctrl: kdump feasibility should fail if no
crash memory") can actually solve this issue.
This patch is a supplement of above-mentioned commit, we bail out
start() even earlier in case of no reserved memory.
Also made some cosmatic changes for check_crash_mem_reserved().
1) Before this patch
$ time kdumpctl start
No memory reserved for crash kernel.
Starting kdump: [FAILED]
real 0m0.282s
user 0m0.184s
sys 0m0.146s
2) After this patch
$ time kdumpctl start
No memory reserved for crash kernel
Starting kdump: [FAILED]
real 0m0.010s
user 0m0.008s
sys 0m0.001s
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Pratyush Anand <panand@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
This patch introduces the 'force_no_rebuild' option
inside the 'kdump.conf' and its handling inside the 'kdumpctl'
script.
There might be several use cases, where a system admin
decides that he doesn't need to rebuild the kdump initrd
and wants to use an existing version of the same. In such cases,
he can set the 'force_no_rebuild' option inside 'kdump.conf'
to 1, to force the 'kdumpctl' script not to rebuild the kdump
initrd.
Signed-off-by: Bhupesh Sharma <bhsharma@redhat.com>
Acked-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
This reverts commit 892bea7aa
We already eliminated the root filesystem by removing "root=X"
in case of non-root dumping, and for livecd it must be non-root
dumping according to "live-image-kdump-howto.txt".
So it's time to revert this commit.
Also update "live-image-kdump-howto.txt", make sure users do not
configure "default dump_to_rootfs".
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Pratyush Anand <panand@redhat.com>
Acked-by:Dave Young <dyoung@redhat.com>
Since the current dracut of Fedora already supports not always
mounting root device, we can remove "root=X" from the command
line directly, and always get the dump target specified in
"/etc/kdump.conf" and mount it. If the dump target is located
at root filesystem, we will add the root mount info explicitly
from kdump side instead of from dracut side.
For example, in case of nfs/ssh/usb/raw/etc(non-root) dumping,
kdump will not mount the unnecessary root fs after this change.
This patch removes "root=X" via the "KDUMP_COMMANDLINE_REMOVE"
(if "default dump_to_rootfs" is specified, don't remove "root=X"),
and mounts non-root target under "/kdumproot", the root target
still under "/sysroot"(to be align with systemd sysroot.mount).
After removing "root=X", we now add root fs mount information
explicitly from the kdump side.
Changed check_dump_fs_modified() a little to avoid rebuild when
dump target is root, since we add root fs mount explicitly now.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Pratyush Anand <panand@redhat.com>
Acked-by:Dave Young <dyoung@redhat.com>
For the following scripts:
cmdline="root=/dev/mapper/fedora-root rd.lvm.lv=fedora/root rw"
remove_cmdline_param $cmdline "root"
cmdline="root=nfs4:192.168.122.9:/ ip=ens3:dhcp rw"
remove_cmdline_param $cmdline "root"
The current implementation will get the wrong results:
"rd.lvm.lv=fedora/ rw"
":/ ip=ens3:dhcp rw"
After this patch we can get the correct results:
"rd.lvm.lv=fedora/root rw"
"ip=ens3:dhcp rw"
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Pratyush Anand <panand@redhat.com>
Acked-by:Dave Young <dyoung@redhat.com>
When kexec_crash_loaded does not exist, means kdump was not enabled in
kernel we get
$ kdumpctl status
cat: /sys/kernel/kexec_crash_loaded: No such file or directory
/usr/bin/kdumpctl: line 879: [: ==: unary operator expected
Kdump is not operational
After this patch:
$ kdumpctl status
Perhaps CONFIG_CRASH_DUMP is not enabled in kernel
Kdump is not operational
Signed-off-by: Pratyush Anand <panand@redhat.com>
Reviewed-by: Bhupesh Sharma <bhsharma@redhat.com>
Reviewed-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Check the number of cpus for x86_64 kdump kernel to boot with.
We met an issue on x86_64: kdump runs out of vectors with the
default "nr_cpus=1", when requesting tons of irqs.
This patch detects such situation and warns users about the risk.
The total number of vectors percpu is 256 defined by x86 architecture.
The available vectors can be allocated to io devices percpu starts
from FIRST_EXTERNAL_VECTOR(see kernel code), and some high-numbered
ones are consumed by some system interrupts. As a result, the vectors
for io device are within [FIRST_EXTERNAL_VECTOR, FIRST_SYSTEM_VECTOR),
with one known exception, 0x80 within the range is reserved specially
as the syscall vector.
FIRST_EXTERNAL_VECTOR is invariably 32, while FIRST_SYSTEM_VECTOR can
vary between different kernel versions. E.g. FIRST_SYSTEM_VECTOR gets
0xef(with CONFIG_X86_LOCAL_APIC on)for linux-4.10, that is 17 vectors
reserved, considering it may increase in the future and the special
vectors, we use a flexible variance and assume there are 32 reserved
from FIRST_EXTERNAL_VECTOR. Then the max vectors for device interrupts
percpu is: (256-32)-32=192, we acquire the number N of device interrupts
from /proc/irq/, then the number of minimal cpus required is calculated:
(N + 192 - 1) / 192
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Pratyush Anand <panand@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Since KDUMP_COMMANDLINE is a global variable, prepare_cmdline can
modify it directly instead of echoing back the result. This change
enables it to output messages.
Changed some coding styles.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Acked-by: Pratyush Anand <panand@redhat.com>
We maintained several kdump specific functions which are duplicate with the
similar versions in dracut, Dracut upstream splitted dracut init stuff from
dracut-functions.sh so that we can source it now.
Notes about kdump_get_presistent_dev:
Dracut now has a persistent_policy feature, for kdump when we dump to
raw disks we do not care the filesystem uuid and labels so we prefer to
search disk id instead. For raw disk set the persistent_policy before calling
get_persistent_dev ensure kdump logic still work.
Tested filesystem and raw dump in kvm guests.
[Xunlei: drop other functions other than get_persistent_dev.]
Signed-off-by: Dave Young <dyoung@redhat.com>
Reviewed-by: Xunlei Pang <xlpang@redhat.com>
When fadump mode is enabled, the default initrd is rebuilt with kdump
dracut module. As the default initrd is altered, the original default
initrd is backed up. But we are not restoring it when fadump mode is
disabled. This patch tries to restore the backed up default initrd on
disabling fadump mode.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Kernels of live images are booted with a kernel parameter which looks
like "root=live:CDLABEL=Fedora-WS-Live-25_A-2". This argument can't be
recognized by dracut during kdump process and will cause failure
of kdump if users didn't set KUDMP_COMMANDLINE in /etc/sysconfig/kdump.
So we should filter out 'root' when we find such a parameter in
/proc/cmdline to make kdump work correctly in live images.
Signed-off-by: Tong Li <tonli@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
We get following error on the systems that have everything built-in and no
initrd is used.
Kernel dev name of /dev/root is not found.
Dump target /dev/root is probably not mounted.
It happens because `df $path` gets /dev/root from /proc/self/mountinfo.
Fix this by identifying real target device when `df $path` returns
Filesystem as /dev/root.
Reported-and-tested-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Pratyush Anand <panand@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Since we also check for mount point of $_target after if/else loop, so
there is no need to do the same thing specifically in else loop as well.
Remove those duplicate statement from else loop.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
On a diskless client /etc/fstab does not exist. Therefore check
modification time of this file for rebuild only if it exists.
Also use --fstab option with findmnt only when /etc/fstab exists.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Reviewed-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
commit "28e8c4b5ac89 kdumpctl: Move file modification check logic in
check_system_modified()" copied file modification check logic instead of
moving.
Kill the duplicate logic from original calling function check_rebuild().
Signed-off-by: Pratyush Anand <panand@redhat.com>
Reviewed-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
There are some complaints about nfs kdump that users must mount
nfs beforehand, which may cause some overhead to nfs server.
For example, there're thounsands of diskless clients deployed with
nfs dumping, each time the client is boot up, it will trigger
kdump rebuilding so will mount nfs, thus resulting in thousands
of nfs request concurrently imposed on the same nfs server.
We introduce a new way of specifying mount information via the
already-existent "dracut_args" directive(so avoid adding extra
directives in /etc/kdump.conf), we will skip all the filesystem
mounting and checking stuff for it. So it can be used in the
above-mentioned nfs scenario to avoid severe nfs server overhead.
Specifically, if there is any "--mount" information specified via
"dracut_args" in /etc/kdump.conf, always use it as the final mount
without any validation(mounting or checking like mount options,
fs size, etc), so users are expected to ensure its correctness.
NOTE:
-Only one mount target is allowed using "dracut_args" globally.
-Dracut will create <mountpoint> if it doesn't exist in kdump kernel,
<mountpoint> must be specified as an absolute path.
-Users should do a test first and ensure it works because kdump does
not prepare the mount or check all the validity.
Reviewed-by: Pratyush Anand <panand@redhat.com>
Suggested-by: Dave Young <dyoung@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
If state of a watchdog device is changed by an user after kdumpctl restart
then initramfs must be rebuilt on the basis of new watchdog status.
Testing:
-------------------------------------------------------
Initramfs wdt state
Prev Current Result
-------------------------------------------------------
Not Exist NA X Rebuild
Exist Inact Inact No Rebuild
Exist Inact Act Force Rebuild
Exist Act Inact Force Rebuild
Exist Act Act(Same wdt) No Rebuild
Exist Act Act(Diff wdt) Force Rebuild
Exist Act Module Removed Force Rebuild
Signed-off-by: Pratyush Anand <panand@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Resolves: BZ1348898
dracut-functions.sh defines a get_persistent_dev(). Earlier, we had another
local get_persistent_dev() in mkdumprd, however that was moved to
kdump-lib.sh, so that it can be reused in kdumpctl.
Since, dracut-module-setup.sh (which is dracut's
99kdumpbase/module-setup.sh) sources kdump-lib.sh. Therefore, once dracut
will execute 99kdumpbase module, it's own get_persistent_dev() function is
overwritten by kdump's version. If any other dracut module calls
get_persistent_dev() thereafter then, kdump's version is executed, which was
not expected.
Therefore rename kdump's get_persistent_dev() as kdump_get_persistent_dev()
to avoid any name contention.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Acked-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Currently initramfs is rebuilt even when crash kernel memory is not
available and then latter on kdump service is failed.
Its better to fail during feasibility itself when crash memory is not
reserved.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Acked-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
kdumpctl passes --device argument if dump target is a raw device. It passes
--mount argument if dump target is either mounted as nfs or as a bulk
device. When dump target device is a root device then it does not pass any
of the above two arguments.
After kdumpctl restart, if there is any change in file system which needs
different dracut arguments, then initramfs must be rebuild.
Modification in filesystem for a raw target does not affect dracut
arguments. So, we do not consider to check any modification if raw target
was specified in kdump.conf.
We might need to change dracut arguments if there is some changes in nfs
and ssh target related files. However, we do not consider them in this
patch.
We mainly consider changes in bulk target specified in kdump.conf. We also
consider changes in bulk and nfs file system, if there was no dump target
specified in kdump.conf but dump path is mounting such file systems.
So the initramfs must be rebuild if, either dump target's persistent path
or it's mount point or its file system type changes. If there is no dump
target specified then, both dump path and root path must mount same device,
otherwise rebuild should be triggered.
Some of the examples when we can need a rebuild:
-- "dump target" is specified as one of ext[234], xfs or btrfs. But after
kdump initramfs building its UUID is changed by reformatting.
-- "dump target" is specified as file system type fs1 (say ext3). But after
kdump initramfs building, user change it to fs2 (say ext4), probably by
a mkfs.ext4 executing on the target device.
-- "dump target" is not specified, but "dump path" mounts a device which
is different than device for root path and either UUID or file system type
is modified after kdump initramfs build.
-- "dump target" is not specified, but "dump path" mounts a nfs device and
nfs host path changes after kdump initramfs build.
Some testing:
Initial conditions:
-- No dump target specified
-- dump path (/var/crash) and root(/) are on same device
-- kdumpctl was already executed once after last modification in
/etc/kdump.conf
# kdumpctl restart
No rebuild
# mkfs.ext2 /dev/md0;mount /dev/md0 /var/crash/;kdumpctl restart
Rebuilt because "Detected change in File System"
# kdumpctl restart
No rebuild
# umount /var/crash/;kdumpctl restart
Rebuilt because "Detected change in File System"
# kdumpctl restart
No rebuild
# mount /dev/md0 /var/crash/;kdumpctl restart
Rebuilt because "Detected change in File System"
# umount /var/crash;mkfs.ext4 /dev/md0;
# mount /dev/md0 /var/crash/;kdumpctl restart
Rebuilt because "Detected change in File System"
# umount /var/crash;mkfs.ext4 /dev/mapper/fedora-swap
# mount /dev/mapper/fedora-swap /var/crash/
# kdumpctl restart
Rebuilt because "Detected change in File System"
# umount /var/crash;mkfs.btrfs /dev/mapper/fedora-swap -f
# mount /dev/mapper/fedora-swap /var/crash/
# kdumpctl restart
Rebuilt because "Detected change in File System"
# kdumpctl restart
No rebuild
# umount /var/crash/;kdumpctl restart
Rebuilt because "Detected change in File System"
# mount /dev/mapper/fedora-swap /var/crash/;kdumpctl restart
Rebuilt because "Detected change in File System"
# umount /var/crash;mkfs.minix /dev/md0
# mount /dev/md0 /var/crash/; kdumpctl restart
Rebuilt because "Detected change in File System"
# kdumpctl restart
No rebuild
# umount /var/crash/;kdumpctl restart
Rebuilt because "Detected change in File System"
# mount 192.168.1.16:/nfsroot /var/crash/;kdumpctl restart
Rebuilt because "Detected change in File System"
# umount /var/crash/;kdumpctl restart
Rebuilt because "Detected change in File System"
# mount 192.168.1.16:/nfsroot /var/crash/;kdumpctl restart
Rebuilt because "Detected change in File System"
# kdumpctl restart
No rebuild
# umount /var/crash;mount 192.168.1.12:/nfsroot /var/crash/
# kdumpctl restart
Rebuilt because "Detected change in File System"
# umount /var/crash/;kdumpctl restart
Rebuilt because "Detected change in File System"
Added "raw /dev/md0" in /etc/kdump.conf
# kdumpctl restart
Rebuilt because "Detected change in /etc/kdump.conf"
# mkfs.ext4 /dev/md0 ;kdumpctl restart
No rebuild
Added "ext4 /dev/md0" in /etc/kdump.conf
# mkfs.ext4 /dev/md0;mount /dev/md0 /mnt
# mkdir /mnt/var;mkdir /mnt/var/crash; kdumpctl restart
Rebuilt because "Detected change in /etc/kdump.conf"
# umount /mnt;mkfs.ext4 /dev/md0;mount /dev/md0 /mnt
# mkdir /mnt/var;mkdir /mnt/var/crash; kdumpctl restart
Rebuilt because "Detected change in /etc/kdump.conf"
Most of the credits for this patch goes to Xunlei Pang <xpang@redhat.com>
for suggesting several improvements.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Acked-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Baoquan He <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Relevant kdump files are also part of system. Therefore, moving logic of
file modification checking in check_system_modified() function now.
No functional changes.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Acked-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Baoquan He <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
There could be some dynamic system modification, which may affect kdump
kernel boot process. In such situation initramfs must be rebuilt on the
basis of changes.
Since most of these checking methods will use information from
TARGET_INITRD, therefore check its existence in common code.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Acked-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Baoquan He <xlpang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
When $KDUMP_BOOTDIR is RO then kexec-tools should not try rebuild initramfs
even when conditions for rebuild is met.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Acked-by: Baoquan He <bhe@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Use KDUMP_COMMANDLINE_REMOVE config instead of hardcode them in
kdumpctl, which makes it possible system admins decide what params to
remove such as "quiet" or other debug flags.
This patch also adds backward compatibility even if an old config is
used. It will behave the same as the old version.
Signed-off-by: Dangyi Liu <dliu@redhat.com>
Acked-by: Baoquan He <bhe@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
slub_debug parameter enables debug for slub, making each object take
more memory than normal. During a typical kdump, "slub_debug=FZPU" will
cost about 33MB additional memory. If users really want to enable this
parameter, they should specify it in KDUMP_COMMANDLINE_APPEND.
Signed-off-by: Dangyi Liu <dliu@redhat.com>
According to man page, default option can only use reboot, halt, poweroff,
shell and dump_to_rootfs as parameter.
Currently, if configuration kdump.conf is:
------
path /var/crash
core_collector makedumpfile -nosuchfile
default no_such_option
------
kdump service still can be started.
Adding function "check_default_config" to kdumpctl file can solve
this problem.
I have tested this patch in my test machine(Fedora-21).
v1 --> v2
Baoquan He point "check_default_config" function should be call in
"check_config" function.
Wang Li point if kdump.conf donesn't configure the "default" option,
kdump serivce will fail.
Signed-off-by: Qiao Zhao <qzhao@redhat.com>
Acked-by: Baoquan He <bhe@redhat.com>
Acked-by: Minfei Huang <mhuang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
For Atomic system, the cmdline will contain the specific string
"ostree". So we can filter out the "ostree" to judge the system is
Atomic or not.
Signed-off-by: Minfei Huang <mhuang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Acked-by: Baoquan He <bhe@redhat.com>
Previously /boot is asumed as the default dir where kernel and initrd
is put. However, the directory containing the running kernel image
on Atomic systems differs in each installation. Usually something like:
/boot/ostree/rhel-atomic-host-b50a015b637c353dc6554c851f8a1212b60d6121a7316715e4a63e2a4113cd72
This means that kdump will not find vmlinuz when installed on an
Atomic host, and thus the kdump service will fail to start.
In this patch, the kdump boot dir finding behaviour is a little changed.
Firstly check whether user has specify a directory explicitly in
/etc/sysconfig/kdump. If yes that is respected. Otherwise we assume
1st kernel and kdump kernel are put in the same place under /boot.
Then find it according /proc/cmdline and append it to /boot/
Note:
So now the KDUMP_BOOTDIR in /etc/sysconfig/kdump is set as empty
by default. If user set KDUMP_BOOTDIR to a directory, then he need to
take care of all related things himself. otherwise kdump script handle
it automatically.
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Acked-by: Minfei Huang <mhuang@redhat.com>
kdumpctl now parses mount points in determining the partition to
save the dump to. So /etc/fstab can be considered a configuration
file for kdump.
Change adds an additional depenedency check on /etc/fstab when
kdump is restarted.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hp.com>
Acked-by: WANG Chao <chaowang@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
With the inclusion of 'panic_on_warn',
http://marc.info/?l=linux-api&m=141570937328528&w=2
and which is now staged in Andrew Morton's tree, we need to remove
'panic_on_warn' from the 2nd kernel's cmdline. If it is included it is
possible a non-fatal warning could panic the second kernel.
Before:
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-3.10.0+
root=/dev/mapper/rhel_intel--canoepass--05-root ro
rd.lvm.lv=rhel_intel-canoepass-05/root
rd.lvm.lv=rhel_intel-canoepass-05/swap console=ttyS0,115200n81
LANG=en_US.UTF-8 systemd.debug panic_on_warn=1 irqpoll nr_cpus=1
reset_devices cgroup_disable=memory mce=off numa=off udev.children-max=2
panic=10 rootflags=nofail acpi_no_memhotplug disable_cpu_apicid=0
elfcorehdr=839092K
After:
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-3.10.0+
root=/dev/mapper/rhel_intel--canoepass--05-root ro
rd.lvm.lv=rhel_intel-canoepass-05/root
rd.lvm.lv=rhel_intel-canoepass-05/swap console=ttyS0,115200n81
LANG=en_US.UTF-8 systemd.debug irqpoll nr_cpus=1 reset_devices
cgroup_disable=memory mce=off numa=off udev.children-max=2 panic=10
rootflags=nofail acpi_no_memhotplug disable_cpu_apicid=0
elfcorehdr=839092K
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Now kexec file based syscall can be used with secureboot enabled machines.
Automatically switch to using new syscall if secureboot is enabled on the
machine.
Also remove the old message where kdump service failed if secureboot is
enabled. That's not the case anymore.
v2:
Renamed "secureboot" to "Secure Boot" in user visible message.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Currently old kexec syscall denies unloading a kernel if secureboot is enabled.
I think this is not right behavior and should be changed. But for now, use
new syscall if secureboot is enabled and that allows unloading kernel.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Does anybody know why are we redirecting stderr to /dev/null when using
kexec load/unload commands? This sounds wrong to me. In case of error I
have no idea what went wrong.
Systemctl already puts all the information in journal. So if we are worried
that user will be bombarded with error messages, that should not be a concern.
So do not redirect stderr to /dev/null.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
When there's no kdump initramfs for lsinitrd to inspect with, there will
be an error:
# kdumpctl start
/boot/initramfs-3.16.0-rc7+kdump.img does not exist
Usage: lsinitrd [options] [<initramfs file> [<filename> [<filename> [...] ]]]
Usage: lsinitrd [options] -k <kernel version>
-h, --help print a help message and exit.
-s, --size sort the contents of the initramfs by size.
-m, --mod list modules.
-f, --file <filename> print the contents of <filename>.
-k, --kver <kernel version> inspect the initramfs of <kernel version>.
No kdump initial ramdisk found.
Rebuilding /boot/initramfs-3.16.0-rc7+kdump.img
[..]
In addition, lsinitrd is a slow operation. We only run it when it's
fadump mode, to speed up in kdump mode.
Signed-off-by: WANG Chao <chaowang@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
In fadump, in case of failure while rebuilding initrd, the error status
is not handled properly. See code snippet below:
$MKDUMPRD $target_initrd_tmp --rebuild $TARGET_INITRD --kver $kdump_kver \
-i /tmp/fadump.initramfs /etc/fadump.initramfs
rm -f /tmp/fadump.initramfs
if [ $? != 0 ]; then
echo "mkdumprd: failed to rebuild initrd with fadump support" >&2
return 1
fi
This patch fixes this issue
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
The script dracut-kdump.sh is responsible for capturing vmcore during
second kernel boot. Currently this script gets installed into kdump
initrd as part of kdumpbase dracut module.
With fadump support, 'dracut-kdump.sh' script also gets installed into
default initrd to capture vmcore generated by firmware assisted dump.
Thus in fadump case, the same initrd is going to be used for normal
boot as well as boot after system crash. Hence a check is required to
see if it is a normal boot or boot after crash.
A new node "ibm,kernel-dump" is added, to the device tree, by firmware
to notify kernel if it is booting after crash. The below patch adds a
check for this node before executing steps to capture vmcore. This
check will help bypassing the vmcore capture steps during normal boot
process.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
The current kdump infrastructure builds a separate initrd which then
gets loaded into memory by kexec-tools for use by kdump kernel. But
firmware assisted dump (FADUMP) does not use kexec-based approach.
After crash, firmware reboots the partition and loads grub loader
like the normal booting process does. Hence in the FADUMP approach,
the second kernel (after crash) will always use the default initrd
(OS built). So, to support FADUMP, change is required, as in to add
dump capturing steps, in this initrd.
The current kdumpctl script implementation already has the code to
build initrd using mkdumprd. This patch uses the new '--rebuild'
option introduced, in dracut, to incrementally build the initramfs
image. Before rebuilding, we may need to probe the initrd image for
fadump support, to avoid rebuilding the initrd image multiple times
unnecessarily. This can be done using "lsinitrd" tool with the newly
proposed '--mod' option & inspecting the presence of "kdumpbase" in
the list of modules of default initrd image. We rebuild the image if
only "kdumpbase" module is missing in the initrd image. Also, before
rebuilding, a backup of default initrd image is taken.
Kexec-tools package in rhel7 is now enhanced to insert a out-of-tree
kdump module for dracut, which is responsible for adding vmcore
capture steps into initrd, if dracut is invoked with "IN_KDUMP"
environment variable set to 1. mkdumprd script exports "IN_KDUMP=1"
environment variable before invoking dracut to build kdump initrd.
This patch relies on this current mechanism of kdump init script.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
During service kdump stop, if firmware assisted dump is enabled
and running, then stop firmware assisted dump by echo'ing 0 to
'/sys/kernel/fadump_registered' file.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
During service kdump start, if firmware assisted dump is not enabled then
fallback to starting of existing kexec based kdump. If firmware assisted
is enabled but not running, then start firmware assisted dump by echo'ing
1 to '/sys/kernel/fadump_registered' file.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
This patch enables kdump script to check if firmware-assisted dump is
enabled or not by reading value from '/sys/kernel/fadump_enabled'. The
determine_dump_mode() routine sets dump_mode to 'fadump', if fadump is
enabled. By default, dump_mode is set to 'kdump' mode.
Modify status routine to check if firmware assisted dump is registered
or not by reading value from '/sys/kernel/fadump_registered' file. If
it is set to '1' then return status=0 else return status=1.
0 <= Firmware assisted is enabled and running
1 <= Firmware assisted is enabled but not running
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
This cleanup patch removes unnecessary keyword "function" at all places in
kdumpctl script. Also, corrects couple of typos in the script.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Vivek suggested we should display message while waiting for the lock,
because the waiting could be long and user will have no idea what's
going on.
So we will repeat the following message every 5 seconds while waiting:
"Another app is currently holding the kdump lock; waiting for it to exit..."
Thanks Vivek for providing a more comprehensive message.
Signed-off-by: WANG Chao <chaowang@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Adds two new options to kdump.conf to be able to configure fence_kdump
support for generic clusters:
fence_kdump_args <arg(s)>
- Command line arguments for fence_kdump_send (it can contain all
valid arguments except hosts to send notification to)
fence_kdump_nodes <node(s)>
- List of cluster node(s) separated by space to send fence_kdump
notification to (this option is mandatory to enable fence_kdump)
Generic clusters fence_kdump configuration take precedence over older
method of fence_kdump configuration for Pacemaker clusters. It means
that if fence_kdump is configured using above options in kdump.conf, old
Pacemaker configuration is not used even if it exists.
Bug-Url: https://bugzilla.redhat.com/1078134
Signed-off-by: Martin Perina <mperina@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Renames check_fence_kdump to check_pcs_fence_kdump to clearly identify
that this method checks only Pacemaker configuration of fence_kdump.
Bug-Url: https://bugzilla.redhat.com/1078134
Signed-off-by: Martin Perina <mperina@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Renames is_fence_kdump to is_pcs_fence_kdump to identify that this
method should be used to detect fence_kdump configuration only in
Pacemaker clusters.
Bug-Url: https://bugzilla.redhat.com/1078134
Signed-off-by: Martin Perina <mperina@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Renames FENCE_KDUMP_CONFIG variable to FENCE_KDUMP_CONFIG_FILE to
distinguish it from values read from fence_kdump_args option in
kdump.conf (introduced in following patches).
Bug-Url: https://bugzilla.redhat.com/1078134
Signed-off-by: Martin Perina <mperina@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
== Version 2 ==
Addresses Vivek's review comments:
1. Don't force numeric in awk script snipet.
2. Command line processing is moved from load_kernel to new function
"prepare_cmdline." This new function is responsible for
setting up the command line passed to KEXEC.
3. New function "append_cmdline" is added to append {argument,value}
pair to command line if argument is not already present.
== Version 1 ==
A recent patch (https://lkml.org/lkml/2014/1/15/42) enables multiple
processors in the crash kernel.
To do this safely the crash kernel needs to know which CPU was the 1st
kernel BSP (bootstrap processor) so that the crash kernel will NOT send
the BSP an INIT. If the crash kernel sends an INIT to the 1st kernel
BSP, some systems may reset or hang.
The EFI spec doesn't require that any particular processor is chosen
as the BSP and the CPU (and its apic id) can change from one boot to
the next. Hence automating the selection of CPU to disable if the
system would panic is desired.
This patch updates the kdumpctl script to get the "initial apicid"
of CPU 0 in the first kernel and will pass this as the
"disable_cpu_apicid=" arguement to kexec if it wasn't explicitly
set in /etc/sysconfig/kdump KDUMP_COMMANDLINE_APPEND.
CPU 0 is chosen as it is the processor thats execute the OS
initialization
code and hence was the BSP as per x86 SDM (Vol 3a Section 8.4.)
See associated Red Hat Bugzilla(s) for additional background material:
https://bugzilla.redhat.com/show_bug.cgi?id=1059031https://bugzilla.redhat.com/show_bug.cgi?id=980621
Signed-off-by: Jerry Hoemann <jerry.hoemann@hp.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Description of problem:
Previously with selinux in enforcing mode, could prevent ssh-keygen from
generating keys. Support for selinux policy for allowing applications to
access ssh-keygen for generating ssh keys was added in
selinux-policy-3.7.19-126.el6_2.6.
Solutions:
Because of the context was added for ssh key generation, so the keys were
generated without fliping from enforcing mode to permissive mode for ssh
key generation. This patch removes selinux code which switches between
enforcing and permissive modes.
Signed-off-by: arthur <zzou@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Move the code to check /sys/kernel/kexec_crash_loaded to function
check_kdump_feasibility(). And rename status() to check_current_kdump_status()
so these two functions become clearer.
cleanup kdumpctl status path as well.
Tested with kernel without CONFIG_KEXEC
Tested with run kdumpctl start two times.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Kdump does not support secure boot yet, so let's claim it is not supported
at the begginning of service start function.
In this patch for checking secure boot status I'm checking the efivars per
suggestion from pjones. see in code comments for the details.
Tested in Fedora 19 + qemu ovmf with secure boot enabled.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
If the system is configured fence kdump, we need to update kdump
initramfs if cluster or fence_kdump config is newer.
In RHEL7, cluster config is no longer keeping locally but stored
remotely. Fortunately we can use a pcs tool to retrieve the xml based
config and parse the last changed time from that.
/etc/sysconfig/fence_kdump is used to configure runtime arguments to
fence_kdump_send. So We have to pass the arguments to 2nd kernel.
When cluster config or /etc/sysconfig/fence_kdump is newer than local
kdump initramfs, we must rebuild initramfs to adapt changes in cluster.
For example:
Detected change(s) the following file(s):
cluster-cib /etc/sysconfig/fence_kdump
Rebuilding /boot/initramfs-xxxkdump.img
[..]
Signed-off-by: WANG Chao <chaowang@redhat.com>
Tested-by: Zhi Zou <zzou@redhat.com>
Tested-by: Marek Grac <mgrac@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
We only allow one instance of kdump service running at each time by
flock /var/lock/kdump which is opened as fd 9 in kdumpctl script.
However a leaking fd issue has been discovered by SELinux:
When executing a specific shell command (not the shell built-in but
provided by other packages, in this case - restorecon) in kdumpctl,
current shell will fork a new subshell for executing and
the subshell will inherit open fd 9 from parent shell. And SELinux
detects that subshell is holding the open fd and consider fd 9 is
leaked.
To avoid this kind of leaking, the most easy way seems to be breaking our
kdumpctl code out into two parts:
- A top level parent shell, which is only used to deal with the lock and
invoking the subshell below.
- A 2nd tier level subshell, which is closing the inherited open fd at
very first and doing the rest of the kdumpctl job. So that it isn't
leaking fd to its subshell when executing like restorecon, etc.
To be easy to understand, the callgraph is roughly like below:
[..]
--> open(9)
--> flock(9)
--> fork
--> close(9) <-- we close 9 right here
--> main() <-- we're now doing the real job
--> [..]
--> fork()
--> restorecon <-- we don't leak fd 9 to child process
--> [..]
--> [..]
As shown above, a wrapper main() is added as the 2nd tier level shell in
this kind of call model. So we can completely avoid leaking fd to
subshell.
Signed-off-by: WANG Chao <chaowang@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
From: Wade Mealing <wmealing@redhat.com>
The RHEL 5 release of mkdumprd allowed for comments in the kdump config
file as shown below:
net 192.168.1.1 # this is the comment part
This patch strips them out during processing, but leaves the configuration
file in original condition.
Signed-off-by: Wade Mealing <wmealing@redhat.com>
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
There will be a race condition if multiple kdumpctl instances are
running at the same time.
By introducing a global mutex lock, only one instance can acquire this
lock and run, others will be waiting for the lock in queue. Now each
kdump instance will be run in serial order and there won't any race
condition.
This is a patch backported from RHEL6.
Signed-off-by: WANG Chao <chaowang@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
2nd kernel has very limited memory. Allocating huge pages will probably
trigger OOM. So let's remove hugepages and hugepagesz kernel parameters
for 2nd kernel when 1st kernel are using them.
If user wants huge pages cmdline in 2nd kernel, he/she can still specify
it through KERNEL_COMMANDLINE_APPEND in /etc/sysconfig/kdump.
This patch adds a new function remove_cmdline_param(). It takes a list
of kernel parameters as its arguments and remove them from given kernel
cmdline.
update:
1. Add description of remove_cmdline_param() per Vivek.
2. Remove_cmdline_param() will take kernel cmdline as $1, then strip it
and print the result.
Signed-off-by: WANG Chao <chaowang@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Dracut root fs is always mounted, but it's not guaranteed to success
because we are in crash/kdump context. So selinux policy can not only
depends on chroot load_policy.
Per discussion with Vivek and Selinux people, relabel kdump files
when the service restart.
Currently only below cases are considerd:
1. target mounted in 1st kernel
2. target mounted as rw, if user mount it as 'ro' they will have to
relabel the files by themselves.
3. save path is not masked, this means if /var/crash is mount to another
disk which is different from dump target it will not visible to user
so user need manually relabel them.
4. only local filesystem based targets.
Tested on F19 machine.
Tested local fs dump and network dump along with different save path
to address above mentioned cases.
Vivek: use function name is_dump_target_configured
use getfattr -m "security.selinux" instead of ".*"
Daniel: use restorecon instead of chcon.
dyoung: keep minix in local fs list since it has not been deperacated yet.
Vivek: wrap is_dump_target_configured checking in function path_to_be_relabeled
dyoung: use awk instead of cut to print config value for different
space delimeters
dyoung: mute df error message: `df $_mnt/$_path 2>/dev/null`
For nfs restorecon, since it will be in 3.11 kernel, we can add it when it's
ok in Fedora.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
mkdumprd call dracut to rebuilding kdump initrd, sometimes passing extra
dracut args is helpful. For example user can enable debug output with
--debug, --printsize to print roughly increased initramfs size by each module,
--omit-drivers to omit kernel modules, etc.
This patch enables dracut_args option for passing extra args to dracut.
Also it modifies add_dracut_arg() to treat a string with-in quote as single
string because for dracut options which has its own args, the args need to be
quoted and space seperated.
If add_dracut_arg() gets an string read from kdump.conf and if that string
contains double quotes, then while converting to positional parameters
those double quotes are not interpreted. Hence if /etc/kdump.conf contains
following.
dracut_args --add-drivers "driver1 driver2"
then add_dracut_args() sees following positional parameters
$1= --add-drivers
$2= "driver1
$3= driver2"
Notice, double quotes have been ignored and parameters have been broken
based on white space.
Modify add_dracut_arg() to look for parameters starting with " and
if one is found, it tries to merge all the next parameters till one
is found with ending double quote. Hence effectively simulating
following behavior.
$1= --add-drivers
$2= "driver1 driver2"
[v1->v2]: address quoted substring in dracut_args, also handle the leading
and ending spaces in substring.
[v2->v3]: fix dracut arguments seperator in kdump.conf.
[v3->v4]: improve changelog, thanks vivek.
[v4->v5]: make the manpage more verbose [vivek].
Tested with below dracut_args test cases:
1. dracut_args --add-drivers "pcspkr virtio_net" --omit-drivers "sdhci-pci hid-logitech-dj e1000"
2. dracut_args --add-drivers " pcspkr virtio_net " --omit-drivers "sdhci-pci hid-logitech-dj e1000"
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Current blacklist option is different from the option in rhel6. In current
implementation blacklist just means omit the driver, but it should really
be preventing it being loaded in initramfs.
To keep consistent, just make the option as deprecated. User is suggested
to user dracut kernel cmdline rd.driver.blacklist instead.
[v1->v2]: improve man page description, thanks Vivek.
Tested in kvm guest with rd.driver.blacklist in kdump sysconfig
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Add a function check_config to check kdump config file.
1. move multi dump target checking into this function
2. check invalid config options and obsolete config options
3. check null config value.
[v2->v3]: add detail doc about deprecated options in kdump.conf manpage.
[v3->v4]: print out the bad config option in case it is not valid.
[v4->v5]: improve documentation according to comments from Vivek.
[v5->v6]: s/Deprecated/Invalid for invalid config options.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Marc Milgram <mmilgram@redhat.com>
check_config is actually checking the files timestamp and rebuilding initrd.
Rename it to check_rebuild instead thus check_config can be used for checking
config file valid or not.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
In old code, kdumpctl program exit directly when check_ssh_target failed
without printing "Starting kdump: FAILED". Then when manually invoke
"kdumpctl restart", only print "Stopping kdump: OK", but no "Starting
kdump: FAILED". That is unreasonable.
In this patch change check_ssh_target() to return when it failed. Then
check the returned value in start() function and print status if the
returned value is not 0.
Meanwhile change "space" to "tab" in function check_ssh_target(), make
those be consistent with the whole script file.
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
In kdumpctl, some printings are incomplete, like "Starting kdump:" or
"Stopping kdump:". Now add the service status to the end of such kind
of printing.
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
In fedora, systemd take control of services. During bootup and manually
invoke "systemctl restart kdump.service", the standard Output/Error
are all redirected to journal/syslog. Then particular LOGGER is useless
in kdumpctl.
In this patch, remove codes related to LOGGER. But for noticing user,
trying to add substituted printing to Standard Output/Err.
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Resolves: bz866357
MEM_RESERVED is for checking if crash memory is reserved or not.
Originally it use /proc/iomem for x86, parsing /proc/cmdline for ppc.
This cause problems for crashkernel=auto, because it does not fit for
the regular expression of [0-9]\+[MmKkGg]@[0-9]\+[MmGgKk]
Fix this by use /sys/kernel/kexec_crash_size for all arches.
After the fix the code is more clear than before.
[v1->v2] vivek: add space between "crash kernel"; remove misleading warning.
Tested-by: Chao Wang <chaowang@redhat.com>
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
We can use not only space but also tab as whitespace,
so s/\ /[[:blank:]] for checking the whitespace
The last commit is intend for checking multiple dump target,
and differentiate ssh and sshkey options. This issue is only
for ssh, so no need to add [[:blank:]] for other dump types to
create a very long code line.
[v1->v2]: use [[:blank:]] instead of [[:space:]]
see expanation in below doc:
http://en.wikipedia.org/wiki/Regular_expression#POSIX_character_classes
[:blank:] [ \t] Space and tab
[:space:] [ \t\r\n\v\f] Whitespace characters
Tested the [:blank:] works well as [:space:]
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
CC: Cong Wang <amwang@redhat.com>
Resolves: bz867703
For both ssh and sshkey specified in kdump.conf, we will error out:
[..]
+ start
+ local nr
++ awk 'BEGIN{cnt=0} /^raw|^ssh|^nfs|^ext[234]|^xfs|^btrfs|^minix/{cnt++} END{print cnt}' /etc/kdump.conf
+ nr=2
+ '[' 2 -gt 1 ']'
+ echo -n 'Error: More than one dump targets specified'
Error: More than one dump targets specified+ echo
Fix this by Improving the patterns for multi dump targes checking
with one more space.
Thanks ChaoWang for catching this and providing the fix.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Add force_rebuild option in kdump.conf
Some user need always force rebuild the dumprd, add an kdump.conf
option force_rebuild here. If force_rebuild is set to 1
kdump initrd will be rebuilt every time then the service starts.
Testing:
Tested below cases:
force_rebuild
force_rebuild 0
force_rebuild 1
force_rebuild 2
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Currently net options means either nfs or ssh dump.
Better to split these two into standalone options. That's more clear to user.
after the split, ssh dump need user specify "ssh user@host"
nfs dump need user specify "nfs host:nfsshare"
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
we now switched to systemd, 'service kdump propagate' does not work anymore.
update the alert message to use 'kdumpctl propagate'
vivek: update kexec-kdump-howto.txt as well.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
exit the saved $? instead of the wrong one after echo line
v1->v2: vivek, save the return value instead of exit 1
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Original patch is from Amerigo, but it has changed a lot:
remove multi dump
refreshed with latest git for the dump instruction function restructure
fixed the behavior of do_kdump_pre, if kdump_pre fails it will reboot
update the docs
check the existance and executable of kdump_pre/post files,
also check the timestamp of them for rebuilding.
refresh patch,
Address comments from vivek:
s/hush/bash in docs
fix the copy-paste error in kdump post error message
s/reboot\/halt/reboot in kexec-kdump-howto.txt
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Resolves: bz805778
Simply the logic and optimize the code
Move check_exist, check_executable, rebuild_initrd to functions
remove BOOTDIR which is not used
Note: There might be modules which are newer than last built initramfs,
we always rebuild the initramfs when extra_moduels= is specified.
Signed-off-by: Dave Young <dyoung@redhat.com>
-d option is not implemented and unused, remove it from mkdumprd
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Resolves: bz805783
kdumpctl: save_raw if found vmcore
mkdumprd: checking available size of raw disk
dracut module: do the dumping
Note, add a dir /kdumpscripts for monitor_dd_progress and future
kdump scripts
[v1->v2]: monitor_dd_process become a script instead of a function
add missed utils
use pipe with dc
[v2->v3]: Don: fix dd_progress_file typo
Vivek: move [ -f $conf_file ] earlier
don't split keyfile= and [ -f keyfile ]
move default core_collector earlier
move non-makedumpfile warnings to mkdumprd
make check available size a common function
Amerigo: use less pipe for grep then awk print
use shell (( )) instead of dc
use cut instead of awk
no need install dc and awk
make DD_BLKSIZE a variable
don't add 0755 file in git, chmod in module-setup.sh
[v3->v4]: vivek: kdumpctl multi raw target handling
monitor_dd_progress- fix wrong size calculation:
the tail -1 of dd pregress file is in bytes instead of blocks
only print the whole dd src file size for non-filtered case
check [ -b raw target device ] before dump
[v4->v5]: vivek: move check [ -b $1 ] before monitor_dd_progress
remove multi target function
[v5->v6]: vivek: only warning for raw dump of non-makedumpfile core_collector
[v6->v7]: kdumpctl should return 0 when there's no raw target
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
remove multi dump
Resolves: bz816859
multi dump was not written as a failsafe dump. Also it was not really tested.
It introduced more complexity in the early phase of porting plenty of rhel6
functions, so we'd remove it and concentrate on the base functionalities.
[v1->v2]: vivek: better error message
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Resolve: bug 807521
The fix is easy.
Command sed should be called with option -n to remain slience when DUMP_TARGET
is a nfs server like 'nfs.server:/mnt/testarea/nfs'.
Then nfs function check_ssh_config will return 1 to not to config nfs like a
ssh dump
Signed-off-by: Chao Wang <chaowang@redhat.com>
Add ssh dump support
changes including below items:
1. sshkey option
2. sshkey propagate
3. fix a bug of _server ip calculation for dump target string
4. change the prefix of kdump hook from 93 to 01 to avoid dhclient and
other cleanups happening before us
5. enable network with dracut cmdline rd.neednet=1 when there's network
target config
[v1 - v2]:
Only check_ssh_target when there's ssh dump target in kdump config file
[v2 -> v3]
style fixes: trailing spaces and space before tab indent
remove set -x
simply check_ssh_target
use awk to get sshkey option value
change pivot hook order to 0000
Signed-off-by: Dave Young <dyoung@redhat.com>
Hari Bathini
Pingfan Liu
Kairui Song
Lianbo Jiang
Kazuhito Hagio
Kenneth Dsouza
Dave Young
Bhupesh Sharma
Baoquan He
Hari Bathini
Xunlei Pang
Ziyue Yang
Pratyush Anand
Tong Li
Dangyi Liu
Qiao Zhao
Minfei Huang
Jerry Hoemann
Prarit Bhargava
Vivek Goyal
WANG Chao
Martin Perina
arthur
Dave Young
Amerigo Wang
Neil Horman