2023-01-11 11:15:11 +00:00
|
|
|
From 113203437eda67261848b14b6c80a33ff7e33d34 Mon Sep 17 00:00:00 2001
|
2022-06-22 17:27:43 +00:00
|
|
|
From: Ilya Leoshkevich <iii@linux.ibm.com>
|
|
|
|
|
Date: Wed, 18 Jul 2018 13:14:07 +0200
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
Subject: [PATCH] Add support for IBM Z hardware-accelerated deflate
|
|
|
|
|
|
2022-06-22 17:27:43 +00:00
|
|
|
IBM Z mainframes starting from version z15 provide DFLTCC instruction,
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
which implements deflate algorithm in hardware with estimated
|
|
|
|
|
compression and decompression performance orders of magnitude faster
|
|
|
|
|
than the current zlib and ratio comparable with that of level 1.
|
|
|
|
|
|
|
|
|
|
This patch adds DFLTCC support to zlib. In order to enable it, the
|
|
|
|
|
following build commands should be used:
|
|
|
|
|
|
2022-06-22 17:27:43 +00:00
|
|
|
$ ./configure --dfltcc
|
|
|
|
|
$ make
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
|
|
|
|
When built like this, zlib would compress in hardware on level 1, and in
|
|
|
|
|
software on all other levels. Decompression will always happen in
|
|
|
|
|
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
|
2022-06-22 17:27:43 +00:00
|
|
|
make it used by default) one could either configure with
|
|
|
|
|
--dfltcc-level-mask=0x7e or set the environment variable
|
|
|
|
|
DFLTCC_LEVEL_MASK to 0x7e at run time.
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
|
|
|
|
Two DFLTCC compression calls produce the same results only when they
|
|
|
|
|
both are made on machines of the same generation, and when the
|
|
|
|
|
respective buffers have the same offset relative to the start of the
|
|
|
|
|
page. Therefore care should be taken when using hardware compression
|
|
|
|
|
when reproducible results are desired. One such use case - reproducible
|
|
|
|
|
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
|
|
|
|
|
environment variable is set, the hardware compression is disabled.
|
|
|
|
|
|
|
|
|
|
DFLTCC does not support every single zlib feature, in particular:
|
|
|
|
|
|
|
|
|
|
* inflate(Z_BLOCK) and inflate(Z_TREES)
|
|
|
|
|
* inflateMark()
|
|
|
|
|
* inflatePrime()
|
2022-06-22 17:27:43 +00:00
|
|
|
* inflateSyncPoint()
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
|
|
|
|
When used, these functions will either switch to software, or, in case
|
|
|
|
|
this is not possible, gracefully fail.
|
|
|
|
|
|
2022-06-22 17:27:43 +00:00
|
|
|
This patch tries to add DFLTCC support in the least intrusive way.
|
|
|
|
|
All SystemZ-specific code is placed into a separate file, but
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
unfortunately there is still a noticeable amount of changes in the
|
2022-06-22 17:27:43 +00:00
|
|
|
main zlib code. Below is the summary of these changes.
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
|
|
|
|
DFLTCC takes as arguments a parameter block, an input buffer, an output
|
|
|
|
|
buffer and a window. Since DFLTCC requires parameter block to be
|
|
|
|
|
doubleword-aligned, and it's reasonable to allocate it alongside
|
|
|
|
|
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
|
|
|
|
|
macros were introduced in order to encapsulate the allocation details.
|
|
|
|
|
The same is true for window, for which ZALLOC_WINDOW and
|
|
|
|
|
TRY_FREE_WINDOW macros were introduced.
|
|
|
|
|
|
2023-01-11 11:15:11 +00:00
|
|
|
Software and hardware window formats do not match, therefore,
|
|
|
|
|
deflateSetDictionary(), deflateGetDictionary(), inflateSetDictionary()
|
|
|
|
|
and inflateGetDictionary() need special handling, which is triggered
|
|
|
|
|
using DEFLATE_SET_DICTIONARY_HOOK, DEFLATE_GET_DICTIONARY_HOOK,
|
|
|
|
|
INFLATE_SET_DICTIONARY_HOOK and INFLATE_GET_DICTIONARY_HOOK macros.
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
|
|
|
|
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
|
|
|
|
|
parameter block, which is allocated alongside zlib state, using
|
|
|
|
|
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
|
|
|
|
|
|
2022-06-22 17:27:43 +00:00
|
|
|
The new DEFLATE_PARAMS_HOOK switches between hardware and software
|
|
|
|
|
deflate implementations when deflateParams() arguments demand this.
|
|
|
|
|
|
|
|
|
|
The new INFLATE_PRIME_HOOK, INFLATE_MARK_HOOK and
|
|
|
|
|
INFLATE_SYNC_POINT_HOOK macros make the respective unsupported calls
|
|
|
|
|
gracefully fail.
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
|
|
|
|
The algorithm implemented in hardware has different compression ratio
|
|
|
|
|
than the one implemented in software. In order for deflateBound() to
|
|
|
|
|
return the correct results for the hardware implementation, the new
|
|
|
|
|
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
|
|
|
|
|
were introduced.
|
|
|
|
|
|
|
|
|
|
Actual compression and decompression are handled by the new DEFLATE_HOOK
|
|
|
|
|
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
|
|
|
|
|
window on its own, calling updatewindow() is suppressed using the new
|
|
|
|
|
INFLATE_NEED_UPDATEWINDOW() macro.
|
|
|
|
|
|
|
|
|
|
In addition to compression, DFLTCC computes CRC-32 and Adler-32
|
|
|
|
|
checksums, therefore, whenever it's used, software checksumming needs to
|
|
|
|
|
be suppressed using the new DEFLATE_NEED_CHECKSUM and
|
|
|
|
|
INFLATE_NEED_CHECKSUM macros.
|
|
|
|
|
|
|
|
|
|
DFLTCC will refuse to write an End-of-block Symbol if there is no input
|
|
|
|
|
data, thus in some cases it is necessary to do this manually. In order
|
|
|
|
|
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
|
|
|
|
|
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
|
|
|
|
|
stream termination must be handled in software as well, block_state enum
|
|
|
|
|
was moved to deflate.h.
|
|
|
|
|
|
|
|
|
|
Since the first call to dfltcc_inflate already needs the window, and it
|
|
|
|
|
might be not allocated yet, inflate_ensure_window was factored out of
|
|
|
|
|
updatewindow and made ZLIB_INTERNAL.
|
|
|
|
|
---
|
2023-01-11 11:15:11 +00:00
|
|
|
Makefile.in | 8 +
|
|
|
|
|
compress.c | 14 +-
|
|
|
|
|
configure | 24 +
|
|
|
|
|
contrib/README.contrib | 4 +
|
|
|
|
|
contrib/s390/README.txt | 17 +
|
|
|
|
|
contrib/s390/dfltcc.c | 1089 +++++++++++++++++++++++++++++++++
|
|
|
|
|
contrib/s390/dfltcc.h | 100 +++
|
|
|
|
|
contrib/s390/dfltcc_deflate.h | 55 ++
|
|
|
|
|
deflate.c | 82 ++-
|
|
|
|
|
deflate.h | 12 +
|
|
|
|
|
gzguts.h | 4 +
|
|
|
|
|
inflate.c | 97 ++-
|
|
|
|
|
inflate.h | 2 +
|
|
|
|
|
test/infcover.c | 4 +-
|
|
|
|
|
test/minigzip.c | 4 +
|
|
|
|
|
trees.c | 13 +-
|
|
|
|
|
zutil.h | 2 +
|
|
|
|
|
17 files changed, 1469 insertions(+), 62 deletions(-)
|
2022-06-22 17:27:43 +00:00
|
|
|
create mode 100644 contrib/s390/README.txt
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
create mode 100644 contrib/s390/dfltcc.c
|
|
|
|
|
create mode 100644 contrib/s390/dfltcc.h
|
|
|
|
|
create mode 100644 contrib/s390/dfltcc_deflate.h
|
|
|
|
|
|
|
|
|
|
diff --git a/Makefile.in b/Makefile.in
|
2023-01-11 11:15:11 +00:00
|
|
|
index 83d8ca4..54c529b 100644
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
--- a/Makefile.in
|
|
|
|
|
+++ b/Makefile.in
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -139,6 +139,14 @@ match.lo: match.S
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
mv _match.o match.lo
|
|
|
|
|
rm -f _match.s
|
|
|
|
|
|
|
|
|
|
+dfltcc.o: $(SRCDIR)contrib/s390/dfltcc.c $(SRCDIR)zlib.h zconf.h
|
|
|
|
|
+ $(CC) $(CFLAGS) $(ZINC) -c -o $@ $(SRCDIR)contrib/s390/dfltcc.c
|
|
|
|
|
+
|
|
|
|
|
+dfltcc.lo: $(SRCDIR)contrib/s390/dfltcc.c $(SRCDIR)zlib.h zconf.h
|
|
|
|
|
+ -@mkdir objs 2>/dev/null || test -d objs
|
|
|
|
|
+ $(CC) $(SFLAGS) $(ZINC) -DPIC -c -o objs/dfltcc.o $(SRCDIR)contrib/s390/dfltcc.c
|
|
|
|
|
+ -@mv objs/dfltcc.o $@
|
|
|
|
|
+
|
2022-10-17 14:31:23 +00:00
|
|
|
crc32_test.o: $(SRCDIR)test/crc32_test.c $(SRCDIR)zlib.h zconf.h
|
|
|
|
|
$(CC) $(CFLAGS) $(ZINCOUT) -c -o $@ $(SRCDIR)test/crc32_test.c
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
2022-06-22 17:27:43 +00:00
|
|
|
diff --git a/compress.c b/compress.c
|
2022-10-17 14:31:23 +00:00
|
|
|
index 2ad5326..179ee27 100644
|
2022-06-22 17:27:43 +00:00
|
|
|
--- a/compress.c
|
|
|
|
|
+++ b/compress.c
|
|
|
|
|
@@ -5,9 +5,15 @@
|
|
|
|
|
|
|
|
|
|
/* @(#) $Id$ */
|
|
|
|
|
|
|
|
|
|
-#define ZLIB_INTERNAL
|
|
|
|
|
+#include "zutil.h"
|
|
|
|
|
#include "zlib.h"
|
|
|
|
|
|
|
|
|
|
+#ifdef DFLTCC
|
|
|
|
|
+# include "contrib/s390/dfltcc.h"
|
|
|
|
|
+#else
|
|
|
|
|
+#define DEFLATE_BOUND_COMPLEN(source_len) 0
|
|
|
|
|
+#endif
|
|
|
|
|
+
|
|
|
|
|
/* ===========================================================================
|
|
|
|
|
Compresses the source buffer into the destination buffer. The level
|
|
|
|
|
parameter has the same meaning as in deflateInit. sourceLen is the byte
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -81,6 +87,12 @@ int ZEXPORT compress(dest, destLen, source, sourceLen)
|
|
|
|
|
uLong ZEXPORT compressBound(sourceLen)
|
2022-06-22 17:27:43 +00:00
|
|
|
uLong sourceLen;
|
|
|
|
|
{
|
|
|
|
|
+ uLong complen = DEFLATE_BOUND_COMPLEN(sourceLen);
|
|
|
|
|
+
|
|
|
|
|
+ if (complen > 0)
|
|
|
|
|
+ /* Architecture-specific code provided an upper bound. */
|
|
|
|
|
+ return complen + ZLIB_WRAPLEN;
|
|
|
|
|
+
|
|
|
|
|
return sourceLen + (sourceLen >> 12) + (sourceLen >> 14) +
|
|
|
|
|
(sourceLen >> 25) + 13;
|
|
|
|
|
}
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
diff --git a/configure b/configure
|
2022-10-17 14:31:23 +00:00
|
|
|
index 45d51e5..ab3204a 100755
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
--- a/configure
|
|
|
|
|
+++ b/configure
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -118,6 +118,7 @@ case "$1" in
|
2022-06-22 17:27:43 +00:00
|
|
|
echo ' configure [--const] [--zprefix] [--prefix=PREFIX] [--eprefix=EXPREFIX]' | tee -a configure.log
|
|
|
|
|
echo ' [--static] [--64] [--libdir=LIBDIR] [--sharedlibdir=LIBDIR]' | tee -a configure.log
|
|
|
|
|
echo ' [--includedir=INCLUDEDIR] [--archs="-arch i386 -arch x86_64"]' | tee -a configure.log
|
|
|
|
|
+ echo ' [--dfltcc] [--dfltcc-level-mask=MASK]' | tee -a configure.log
|
|
|
|
|
exit 0 ;;
|
|
|
|
|
-p*=* | --prefix=*) prefix=`echo $1 | sed 's/.*=//'`; shift ;;
|
|
|
|
|
-e*=* | --eprefix=*) exec_prefix=`echo $1 | sed 's/.*=//'`; shift ;;
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -142,6 +143,16 @@ case "$1" in
|
2022-06-22 17:27:43 +00:00
|
|
|
-w* | --warn) warn=1; shift ;;
|
|
|
|
|
-d* | --debug) debug=1; shift ;;
|
|
|
|
|
--sanitize) sanitize=1; shift ;;
|
|
|
|
|
+ --dfltcc)
|
|
|
|
|
+ CFLAGS="$CFLAGS -DDFLTCC"
|
|
|
|
|
+ OBJC="$OBJC dfltcc.o"
|
|
|
|
|
+ PIC_OBJC="$PIC_OBJC dfltcc.lo"
|
|
|
|
|
+ shift
|
|
|
|
|
+ ;;
|
|
|
|
|
+ --dfltcc-level-mask=*)
|
|
|
|
|
+ CFLAGS="$CFLAGS -DDFLTCC_LEVEL_MASK=`echo $1 | sed 's/.*=//'`"
|
|
|
|
|
+ shift
|
|
|
|
|
+ ;;
|
|
|
|
|
*)
|
|
|
|
|
echo "unknown option: $1" | tee -a configure.log
|
|
|
|
|
echo "$0 --help for help" | tee -a configure.log
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -828,6 +839,19 @@ EOF
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
fi
|
|
|
|
|
fi
|
|
|
|
|
|
|
|
|
|
+# Check whether sys/sdt.h is available
|
|
|
|
|
+cat > $test.c << EOF
|
|
|
|
|
+#include <sys/sdt.h>
|
|
|
|
|
+int main() { return 0; }
|
|
|
|
|
+EOF
|
2022-06-22 17:27:43 +00:00
|
|
|
+if try $CC -c $CFLAGS $test.c; then
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ echo "Checking for sys/sdt.h ... Yes." | tee -a configure.log
|
|
|
|
|
+ CFLAGS="$CFLAGS -DHAVE_SYS_SDT_H"
|
|
|
|
|
+ SFLAGS="$SFLAGS -DHAVE_SYS_SDT_H"
|
|
|
|
|
+else
|
|
|
|
|
+ echo "Checking for sys/sdt.h ... No." | tee -a configure.log
|
|
|
|
|
+fi
|
|
|
|
|
+
|
2022-10-17 14:31:23 +00:00
|
|
|
# test to see if we can use a gnu indirection function to detect and load optimized code at runtime
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
echo >> configure.log
|
2022-10-17 14:31:23 +00:00
|
|
|
cat > $test.c <<EOF
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
diff --git a/contrib/README.contrib b/contrib/README.contrib
|
2022-10-17 14:31:23 +00:00
|
|
|
index 90170df..a36d404 100644
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
--- a/contrib/README.contrib
|
|
|
|
|
+++ b/contrib/README.contrib
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -55,6 +55,10 @@ puff/ by Mark Adler <madler@alumni.caltech.edu>
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
Small, low memory usage inflate. Also serves to provide an
|
|
|
|
|
unambiguous description of the deflate format.
|
|
|
|
|
|
|
|
|
|
+s390/ by Ilya Leoshkevich <iii@linux.ibm.com>
|
|
|
|
|
+ Hardware-accelerated deflate on IBM Z with DEFLATE CONVERSION CALL
|
|
|
|
|
+ instruction.
|
|
|
|
|
+
|
|
|
|
|
testzlib/ by Gilles Vollant <info@winimage.com>
|
|
|
|
|
Example of the use of zlib
|
|
|
|
|
|
2022-06-22 17:27:43 +00:00
|
|
|
diff --git a/contrib/s390/README.txt b/contrib/s390/README.txt
|
|
|
|
|
new file mode 100644
|
2022-10-17 14:31:23 +00:00
|
|
|
index 0000000..48be008
|
2022-06-22 17:27:43 +00:00
|
|
|
--- /dev/null
|
|
|
|
|
+++ b/contrib/s390/README.txt
|
|
|
|
|
@@ -0,0 +1,17 @@
|
|
|
|
|
+IBM Z mainframes starting from version z15 provide DFLTCC instruction,
|
|
|
|
|
+which implements deflate algorithm in hardware with estimated
|
|
|
|
|
+compression and decompression performance orders of magnitude faster
|
|
|
|
|
+than the current zlib and ratio comparable with that of level 1.
|
|
|
|
|
+
|
|
|
|
|
+This directory adds DFLTCC support. In order to enable it, the following
|
|
|
|
|
+build commands should be used:
|
|
|
|
|
+
|
|
|
|
|
+ $ ./configure --dfltcc
|
|
|
|
|
+ $ make
|
|
|
|
|
+
|
|
|
|
|
+When built like this, zlib would compress in hardware on level 1, and in
|
|
|
|
|
+software on all other levels. Decompression will always happen in
|
|
|
|
|
+hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
|
|
|
|
|
+make it used by default) one could either configure with
|
|
|
|
|
+--dfltcc-level-mask=0x7e or set the environment variable
|
|
|
|
|
+DFLTCC_LEVEL_MASK to 0x7e at run time.
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
diff --git a/contrib/s390/dfltcc.c b/contrib/s390/dfltcc.c
|
|
|
|
|
new file mode 100644
|
2023-01-11 11:15:11 +00:00
|
|
|
index 0000000..b8c20bd
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
--- /dev/null
|
|
|
|
|
+++ b/contrib/s390/dfltcc.c
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -0,0 +1,1089 @@
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+/* dfltcc.c - SystemZ DEFLATE CONVERSION CALL support. */
|
|
|
|
|
+
|
|
|
|
|
+/*
|
|
|
|
|
+ Use the following commands to build zlib with DFLTCC support:
|
2022-06-22 17:27:43 +00:00
|
|
|
+
|
|
|
|
|
+ $ ./configure --dfltcc
|
|
|
|
|
+ $ make
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+*/
|
|
|
|
|
+
|
|
|
|
|
+#define _GNU_SOURCE
|
|
|
|
|
+#include <ctype.h>
|
2022-06-22 17:27:43 +00:00
|
|
|
+#include <errno.h>
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+#include <inttypes.h>
|
|
|
|
|
+#include <stddef.h>
|
|
|
|
|
+#include <stdio.h>
|
|
|
|
|
+#include <stdint.h>
|
|
|
|
|
+#include <stdlib.h>
|
|
|
|
|
+#include "../../zutil.h"
|
|
|
|
|
+#include "../../deflate.h"
|
|
|
|
|
+#include "../../inftrees.h"
|
|
|
|
|
+#include "../../inflate.h"
|
|
|
|
|
+#include "dfltcc.h"
|
|
|
|
|
+#include "dfltcc_deflate.h"
|
|
|
|
|
+#ifdef HAVE_SYS_SDT_H
|
|
|
|
|
+#include <sys/sdt.h>
|
|
|
|
|
+#endif
|
|
|
|
|
+
|
|
|
|
|
+/*
|
|
|
|
|
+ C wrapper for the DEFLATE CONVERSION CALL instruction.
|
|
|
|
|
+ */
|
|
|
|
|
+typedef enum {
|
|
|
|
|
+ DFLTCC_CC_OK = 0,
|
|
|
|
|
+ DFLTCC_CC_OP1_TOO_SHORT = 1,
|
|
|
|
|
+ DFLTCC_CC_OP2_TOO_SHORT = 2,
|
|
|
|
|
+ DFLTCC_CC_OP2_CORRUPT = 2,
|
|
|
|
|
+ DFLTCC_CC_AGAIN = 3,
|
|
|
|
|
+} dfltcc_cc;
|
|
|
|
|
+
|
|
|
|
|
+#define DFLTCC_QAF 0
|
|
|
|
|
+#define DFLTCC_GDHT 1
|
|
|
|
|
+#define DFLTCC_CMPR 2
|
|
|
|
|
+#define DFLTCC_XPND 4
|
|
|
|
|
+#define HBT_CIRCULAR (1 << 7)
|
|
|
|
|
+#define HB_BITS 15
|
|
|
|
|
+#define HB_SIZE (1 << HB_BITS)
|
|
|
|
|
+#define DFLTCC_FACILITY 151
|
|
|
|
|
+
|
|
|
|
|
+local inline dfltcc_cc dfltcc OF((int fn, void *param,
|
|
|
|
|
+ Bytef **op1, size_t *len1,
|
|
|
|
|
+ z_const Bytef **op2, size_t *len2,
|
|
|
|
|
+ void *hist));
|
|
|
|
|
+local inline dfltcc_cc dfltcc(fn, param, op1, len1, op2, len2, hist)
|
|
|
|
|
+ int fn;
|
|
|
|
|
+ void *param;
|
|
|
|
|
+ Bytef **op1;
|
|
|
|
|
+ size_t *len1;
|
|
|
|
|
+ z_const Bytef **op2;
|
|
|
|
|
+ size_t *len2;
|
|
|
|
|
+ void *hist;
|
|
|
|
|
+{
|
|
|
|
|
+ Bytef *t2 = op1 ? *op1 : NULL;
|
|
|
|
|
+ size_t t3 = len1 ? *len1 : 0;
|
|
|
|
|
+ z_const Bytef *t4 = op2 ? *op2 : NULL;
|
|
|
|
|
+ size_t t5 = len2 ? *len2 : 0;
|
|
|
|
|
+ register int r0 __asm__("r0") = fn;
|
|
|
|
|
+ register void *r1 __asm__("r1") = param;
|
|
|
|
|
+ register Bytef *r2 __asm__("r2") = t2;
|
|
|
|
|
+ register size_t r3 __asm__("r3") = t3;
|
|
|
|
|
+ register z_const Bytef *r4 __asm__("r4") = t4;
|
|
|
|
|
+ register size_t r5 __asm__("r5") = t5;
|
|
|
|
|
+ int cc;
|
|
|
|
|
+
|
|
|
|
|
+ __asm__ volatile(
|
|
|
|
|
+#ifdef HAVE_SYS_SDT_H
|
|
|
|
|
+ STAP_PROBE_ASM(zlib, dfltcc_entry,
|
|
|
|
|
+ STAP_PROBE_ASM_TEMPLATE(5))
|
|
|
|
|
+#endif
|
|
|
|
|
+ ".insn rrf,0xb9390000,%[r2],%[r4],%[hist],0\n"
|
|
|
|
|
+#ifdef HAVE_SYS_SDT_H
|
|
|
|
|
+ STAP_PROBE_ASM(zlib, dfltcc_exit,
|
|
|
|
|
+ STAP_PROBE_ASM_TEMPLATE(5))
|
|
|
|
|
+#endif
|
|
|
|
|
+ "ipm %[cc]\n"
|
|
|
|
|
+ : [r2] "+r" (r2)
|
|
|
|
|
+ , [r3] "+r" (r3)
|
|
|
|
|
+ , [r4] "+r" (r4)
|
|
|
|
|
+ , [r5] "+r" (r5)
|
|
|
|
|
+ , [cc] "=r" (cc)
|
|
|
|
|
+ : [r0] "r" (r0)
|
|
|
|
|
+ , [r1] "r" (r1)
|
|
|
|
|
+ , [hist] "r" (hist)
|
|
|
|
|
+#ifdef HAVE_SYS_SDT_H
|
|
|
|
|
+ , STAP_PROBE_ASM_OPERANDS(5, r2, r3, r4, r5, hist)
|
|
|
|
|
+#endif
|
|
|
|
|
+ : "cc", "memory");
|
|
|
|
|
+ t2 = r2; t3 = r3; t4 = r4; t5 = r5;
|
|
|
|
|
+
|
|
|
|
|
+ if (op1)
|
|
|
|
|
+ *op1 = t2;
|
|
|
|
|
+ if (len1)
|
|
|
|
|
+ *len1 = t3;
|
|
|
|
|
+ if (op2)
|
|
|
|
|
+ *op2 = t4;
|
|
|
|
|
+ if (len2)
|
|
|
|
|
+ *len2 = t5;
|
|
|
|
|
+ return (cc >> 28) & 3;
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+/*
|
|
|
|
|
+ Parameter Block for Query Available Functions.
|
|
|
|
|
+ */
|
|
|
|
|
+#define static_assert(c, msg) \
|
|
|
|
|
+ __attribute__((unused)) \
|
|
|
|
|
+ static char static_assert_failed_ ## msg[c ? 1 : -1]
|
|
|
|
|
+
|
|
|
|
|
+struct dfltcc_qaf_param {
|
|
|
|
|
+ char fns[16];
|
|
|
|
|
+ char reserved1[8];
|
|
|
|
|
+ char fmts[2];
|
|
|
|
|
+ char reserved2[6];
|
|
|
|
|
+};
|
|
|
|
|
+
|
|
|
|
|
+static_assert(sizeof(struct dfltcc_qaf_param) == 32,
|
|
|
|
|
+ sizeof_struct_dfltcc_qaf_param_is_32);
|
|
|
|
|
+
|
|
|
|
|
+local inline int is_bit_set OF((const char *bits, int n));
|
|
|
|
|
+local inline int is_bit_set(bits, n)
|
|
|
|
|
+ const char *bits;
|
|
|
|
|
+ int n;
|
|
|
|
|
+{
|
|
|
|
|
+ return bits[n / 8] & (1 << (7 - (n % 8)));
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+local inline void clear_bit OF((char *bits, int n));
|
|
|
|
|
+local inline void clear_bit(bits, n)
|
|
|
|
|
+ char *bits;
|
|
|
|
|
+ int n;
|
|
|
|
|
+{
|
|
|
|
|
+ bits[n / 8] &= ~(1 << (7 - (n % 8)));
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+#define DFLTCC_FMT0 0
|
|
|
|
|
+
|
|
|
|
|
+/*
|
|
|
|
|
+ Parameter Block for Generate Dynamic-Huffman Table, Compress and Expand.
|
|
|
|
|
+ */
|
|
|
|
|
+#define CVT_CRC32 0
|
|
|
|
|
+#define CVT_ADLER32 1
|
|
|
|
|
+#define HTT_FIXED 0
|
|
|
|
|
+#define HTT_DYNAMIC 1
|
|
|
|
|
+
|
|
|
|
|
+struct dfltcc_param_v0 {
|
|
|
|
|
+ uint16_t pbvn; /* Parameter-Block-Version Number */
|
|
|
|
|
+ uint8_t mvn; /* Model-Version Number */
|
|
|
|
|
+ uint8_t ribm; /* Reserved for IBM use */
|
|
|
|
|
+ unsigned reserved32 : 31;
|
|
|
|
|
+ unsigned cf : 1; /* Continuation Flag */
|
|
|
|
|
+ uint8_t reserved64[8];
|
|
|
|
|
+ unsigned nt : 1; /* New Task */
|
|
|
|
|
+ unsigned reserved129 : 1;
|
|
|
|
|
+ unsigned cvt : 1; /* Check Value Type */
|
|
|
|
|
+ unsigned reserved131 : 1;
|
|
|
|
|
+ unsigned htt : 1; /* Huffman-Table Type */
|
|
|
|
|
+ unsigned bcf : 1; /* Block-Continuation Flag */
|
|
|
|
|
+ unsigned bcc : 1; /* Block Closing Control */
|
|
|
|
|
+ unsigned bhf : 1; /* Block Header Final */
|
|
|
|
|
+ unsigned reserved136 : 1;
|
|
|
|
|
+ unsigned reserved137 : 1;
|
|
|
|
|
+ unsigned dhtgc : 1; /* DHT Generation Control */
|
|
|
|
|
+ unsigned reserved139 : 5;
|
|
|
|
|
+ unsigned reserved144 : 5;
|
|
|
|
|
+ unsigned sbb : 3; /* Sub-Byte Boundary */
|
|
|
|
|
+ uint8_t oesc; /* Operation-Ending-Supplemental Code */
|
|
|
|
|
+ unsigned reserved160 : 12;
|
|
|
|
|
+ unsigned ifs : 4; /* Incomplete-Function Status */
|
|
|
|
|
+ uint16_t ifl; /* Incomplete-Function Length */
|
|
|
|
|
+ uint8_t reserved192[8];
|
|
|
|
|
+ uint8_t reserved256[8];
|
|
|
|
|
+ uint8_t reserved320[4];
|
|
|
|
|
+ uint16_t hl; /* History Length */
|
|
|
|
|
+ unsigned reserved368 : 1;
|
|
|
|
|
+ uint16_t ho : 15; /* History Offset */
|
|
|
|
|
+ uint32_t cv; /* Check Value */
|
|
|
|
|
+ unsigned eobs : 15; /* End-of-block Symbol */
|
|
|
|
|
+ unsigned reserved431: 1;
|
|
|
|
|
+ uint8_t eobl : 4; /* End-of-block Length */
|
|
|
|
|
+ unsigned reserved436 : 12;
|
|
|
|
|
+ unsigned reserved448 : 4;
|
|
|
|
|
+ uint16_t cdhtl : 12; /* Compressed-Dynamic-Huffman Table
|
|
|
|
|
+ Length */
|
|
|
|
|
+ uint8_t reserved464[6];
|
|
|
|
|
+ uint8_t cdht[288];
|
|
|
|
|
+ uint8_t reserved[32];
|
|
|
|
|
+ uint8_t csb[1152];
|
|
|
|
|
+};
|
|
|
|
|
+
|
|
|
|
|
+static_assert(sizeof(struct dfltcc_param_v0) == 1536,
|
|
|
|
|
+ sizeof_struct_dfltcc_param_v0_is_1536);
|
|
|
|
|
+
|
|
|
|
|
+local z_const char *oesc_msg OF((char *buf, int oesc));
|
|
|
|
|
+local z_const char *oesc_msg(buf, oesc)
|
|
|
|
|
+ char *buf;
|
|
|
|
|
+ int oesc;
|
|
|
|
|
+{
|
|
|
|
|
+ if (oesc == 0x00)
|
|
|
|
|
+ return NULL; /* Successful completion */
|
|
|
|
|
+ else {
|
|
|
|
|
+ sprintf(buf, "Operation-Ending-Supplemental Code is 0x%.2X", oesc);
|
|
|
|
|
+ return buf;
|
|
|
|
|
+ }
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+/*
|
|
|
|
|
+ Extension of inflate_state and deflate_state. Must be doubleword-aligned.
|
|
|
|
|
+*/
|
|
|
|
|
+struct dfltcc_state {
|
|
|
|
|
+ struct dfltcc_param_v0 param; /* Parameter block. */
|
|
|
|
|
+ struct dfltcc_qaf_param af; /* Available functions. */
|
|
|
|
|
+ uLong level_mask; /* Levels on which to use DFLTCC */
|
|
|
|
|
+ uLong block_size; /* New block each X bytes */
|
|
|
|
|
+ uLong block_threshold; /* New block after total_in > X */
|
|
|
|
|
+ uLong dht_threshold; /* New block only if avail_in >= X */
|
|
|
|
|
+ char msg[64]; /* Buffer for strm->msg */
|
|
|
|
|
+};
|
|
|
|
|
+
|
|
|
|
|
+#define ALIGN_UP(p, size) \
|
|
|
|
|
+ (__typeof__(p))(((uintptr_t)(p) + ((size) - 1)) & ~((size) - 1))
|
|
|
|
|
+
|
|
|
|
|
+#define GET_DFLTCC_STATE(state) ((struct dfltcc_state FAR *)( \
|
|
|
|
|
+ (char FAR *)(state) + ALIGN_UP(sizeof(*state), 8)))
|
|
|
|
|
+
|
|
|
|
|
+/*
|
|
|
|
|
+ Compress.
|
|
|
|
|
+ */
|
2022-06-22 17:27:43 +00:00
|
|
|
+local inline int dfltcc_can_deflate_with_params(z_streamp strm,
|
|
|
|
|
+ int level,
|
|
|
|
|
+ uInt window_bits,
|
|
|
|
|
+ int strategy);
|
|
|
|
|
+local inline int dfltcc_can_deflate_with_params(strm,
|
|
|
|
|
+ level,
|
|
|
|
|
+ window_bits,
|
|
|
|
|
+ strategy)
|
|
|
|
|
+ z_streamp strm;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ int level;
|
|
|
|
|
+ uInt window_bits;
|
|
|
|
|
+ int strategy;
|
|
|
|
|
+{
|
|
|
|
|
+ deflate_state FAR *state = (deflate_state FAR *)strm->state;
|
|
|
|
|
+ struct dfltcc_state FAR *dfltcc_state = GET_DFLTCC_STATE(state);
|
|
|
|
|
+
|
|
|
|
|
+ /* Unsupported compression settings */
|
2022-06-22 17:27:43 +00:00
|
|
|
+ if ((dfltcc_state->level_mask & (1 << level)) == 0)
|
|
|
|
|
+ return 0;
|
|
|
|
|
+ if (window_bits != HB_BITS)
|
|
|
|
|
+ return 0;
|
|
|
|
|
+ if (strategy != Z_FIXED && strategy != Z_DEFAULT_STRATEGY)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ return 0;
|
|
|
|
|
+
|
|
|
|
|
+ /* Unsupported hardware */
|
|
|
|
|
+ if (!is_bit_set(dfltcc_state->af.fns, DFLTCC_GDHT) ||
|
|
|
|
|
+ !is_bit_set(dfltcc_state->af.fns, DFLTCC_CMPR) ||
|
|
|
|
|
+ !is_bit_set(dfltcc_state->af.fmts, DFLTCC_FMT0))
|
|
|
|
|
+ return 0;
|
|
|
|
|
+
|
|
|
|
|
+ return 1;
|
|
|
|
|
+}
|
|
|
|
|
+
|
2022-06-22 17:27:43 +00:00
|
|
|
+int ZLIB_INTERNAL dfltcc_can_deflate(strm)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+{
|
|
|
|
|
+ deflate_state FAR *state = (deflate_state FAR *)strm->state;
|
|
|
|
|
+
|
|
|
|
|
+ return dfltcc_can_deflate_with_params(strm,
|
|
|
|
|
+ state->level,
|
|
|
|
|
+ state->w_bits,
|
|
|
|
|
+ state->strategy);
|
|
|
|
|
+}
|
|
|
|
|
+
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+local void dfltcc_gdht OF((z_streamp strm));
|
|
|
|
|
+local void dfltcc_gdht(strm)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+{
|
|
|
|
|
+ deflate_state FAR *state = (deflate_state FAR *)strm->state;
|
|
|
|
|
+ struct dfltcc_param_v0 FAR *param = &GET_DFLTCC_STATE(state)->param;
|
|
|
|
|
+ size_t avail_in = avail_in = strm->avail_in;
|
|
|
|
|
+
|
|
|
|
|
+ dfltcc(DFLTCC_GDHT,
|
|
|
|
|
+ param, NULL, NULL,
|
|
|
|
|
+ &strm->next_in, &avail_in, NULL);
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+local dfltcc_cc dfltcc_cmpr OF((z_streamp strm));
|
|
|
|
|
+local dfltcc_cc dfltcc_cmpr(strm)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+{
|
|
|
|
|
+ deflate_state FAR *state = (deflate_state FAR *)strm->state;
|
|
|
|
|
+ struct dfltcc_param_v0 FAR *param = &GET_DFLTCC_STATE(state)->param;
|
|
|
|
|
+ size_t avail_in = strm->avail_in;
|
|
|
|
|
+ size_t avail_out = strm->avail_out;
|
|
|
|
|
+ dfltcc_cc cc;
|
|
|
|
|
+
|
|
|
|
|
+ cc = dfltcc(DFLTCC_CMPR | HBT_CIRCULAR,
|
|
|
|
|
+ param, &strm->next_out, &avail_out,
|
|
|
|
|
+ &strm->next_in, &avail_in, state->window);
|
|
|
|
|
+ strm->total_in += (strm->avail_in - avail_in);
|
|
|
|
|
+ strm->total_out += (strm->avail_out - avail_out);
|
|
|
|
|
+ strm->avail_in = avail_in;
|
|
|
|
|
+ strm->avail_out = avail_out;
|
|
|
|
|
+ return cc;
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+local void send_eobs OF((z_streamp strm,
|
|
|
|
|
+ z_const struct dfltcc_param_v0 FAR *param));
|
|
|
|
|
+local void send_eobs(strm, param)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+ z_const struct dfltcc_param_v0 FAR *param;
|
|
|
|
|
+{
|
|
|
|
|
+ deflate_state FAR *state = (deflate_state FAR *)strm->state;
|
|
|
|
|
+
|
|
|
|
|
+ _tr_send_bits(
|
|
|
|
|
+ state,
|
|
|
|
|
+ bi_reverse(param->eobs >> (15 - param->eobl), param->eobl),
|
|
|
|
|
+ param->eobl);
|
|
|
|
|
+ flush_pending(strm);
|
|
|
|
|
+ if (state->pending != 0) {
|
|
|
|
|
+ /* The remaining data is located in pending_out[0:pending]. If someone
|
|
|
|
|
+ * calls put_byte() - this might happen in deflate() - the byte will be
|
|
|
|
|
+ * placed into pending_buf[pending], which is incorrect. Move the
|
|
|
|
|
+ * remaining data to the beginning of pending_buf so that put_byte() is
|
|
|
|
|
+ * usable again.
|
|
|
|
|
+ */
|
|
|
|
|
+ memmove(state->pending_buf, state->pending_out, state->pending);
|
|
|
|
|
+ state->pending_out = state->pending_buf;
|
|
|
|
|
+ }
|
|
|
|
|
+#ifdef ZLIB_DEBUG
|
|
|
|
|
+ state->compressed_len += param->eobl;
|
|
|
|
|
+#endif
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_deflate(strm, flush, result)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+ int flush;
|
|
|
|
|
+ block_state *result;
|
|
|
|
|
+{
|
|
|
|
|
+ deflate_state FAR *state = (deflate_state FAR *)strm->state;
|
|
|
|
|
+ struct dfltcc_state FAR *dfltcc_state = GET_DFLTCC_STATE(state);
|
|
|
|
|
+ struct dfltcc_param_v0 FAR *param = &dfltcc_state->param;
|
|
|
|
|
+ uInt masked_avail_in;
|
|
|
|
|
+ dfltcc_cc cc;
|
|
|
|
|
+ int need_empty_block;
|
|
|
|
|
+ int soft_bcc;
|
|
|
|
|
+ int no_flush;
|
|
|
|
|
+
|
2022-06-22 17:27:43 +00:00
|
|
|
+ if (!dfltcc_can_deflate(strm)) {
|
|
|
|
|
+ /* Clear history. */
|
|
|
|
|
+ if (flush == Z_FULL_FLUSH)
|
|
|
|
|
+ param->hl = 0;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ return 0;
|
2022-06-22 17:27:43 +00:00
|
|
|
+ }
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+
|
|
|
|
|
+again:
|
|
|
|
|
+ masked_avail_in = 0;
|
|
|
|
|
+ soft_bcc = 0;
|
|
|
|
|
+ no_flush = flush == Z_NO_FLUSH;
|
|
|
|
|
+
|
2022-06-22 17:27:43 +00:00
|
|
|
+ /* No input data. Return, except when Continuation Flag is set, which means
|
|
|
|
|
+ * that DFLTCC has buffered some output in the parameter block and needs to
|
|
|
|
|
+ * be called again in order to flush it.
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ */
|
2022-06-22 17:27:43 +00:00
|
|
|
+ if (strm->avail_in == 0 && !param->cf) {
|
|
|
|
|
+ /* A block is still open, and the hardware does not support closing
|
|
|
|
|
+ * blocks without adding data. Thus, close it manually.
|
|
|
|
|
+ */
|
|
|
|
|
+ if (!no_flush && param->bcf) {
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ send_eobs(strm, param);
|
|
|
|
|
+ param->bcf = 0;
|
|
|
|
|
+ }
|
2022-06-22 17:27:43 +00:00
|
|
|
+ /* Let one of deflate_* functions write a trailing empty block. */
|
|
|
|
|
+ if (flush == Z_FINISH)
|
|
|
|
|
+ return 0;
|
|
|
|
|
+ /* Clear history. */
|
|
|
|
|
+ if (flush == Z_FULL_FLUSH)
|
|
|
|
|
+ param->hl = 0;
|
|
|
|
|
+ /* Trigger block post-processing if necessary. */
|
|
|
|
|
+ *result = no_flush ? need_more : block_done;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ return 1;
|
|
|
|
|
+ }
|
|
|
|
|
+
|
|
|
|
|
+ /* There is an open non-BFINAL block, we are not going to close it just
|
|
|
|
|
+ * yet, we have compressed more than DFLTCC_BLOCK_SIZE bytes and we see
|
|
|
|
|
+ * more than DFLTCC_DHT_MIN_SAMPLE_SIZE bytes. Open a new block with a new
|
|
|
|
|
+ * DHT in order to adapt to a possibly changed input data distribution.
|
|
|
|
|
+ */
|
|
|
|
|
+ if (param->bcf && no_flush &&
|
|
|
|
|
+ strm->total_in > dfltcc_state->block_threshold &&
|
|
|
|
|
+ strm->avail_in >= dfltcc_state->dht_threshold) {
|
|
|
|
|
+ if (param->cf) {
|
|
|
|
|
+ /* We need to flush the DFLTCC buffer before writing the
|
|
|
|
|
+ * End-of-block Symbol. Mask the input data and proceed as usual.
|
|
|
|
|
+ */
|
|
|
|
|
+ masked_avail_in += strm->avail_in;
|
|
|
|
|
+ strm->avail_in = 0;
|
|
|
|
|
+ no_flush = 0;
|
|
|
|
|
+ } else {
|
|
|
|
|
+ /* DFLTCC buffer is empty, so we can manually write the
|
|
|
|
|
+ * End-of-block Symbol right away.
|
|
|
|
|
+ */
|
|
|
|
|
+ send_eobs(strm, param);
|
|
|
|
|
+ param->bcf = 0;
|
|
|
|
|
+ dfltcc_state->block_threshold =
|
|
|
|
|
+ strm->total_in + dfltcc_state->block_size;
|
|
|
|
|
+ }
|
|
|
|
|
+ }
|
|
|
|
|
+
|
2022-06-22 17:27:43 +00:00
|
|
|
+ /* No space for compressed data. If we proceed, dfltcc_cmpr() will return
|
|
|
|
|
+ * DFLTCC_CC_OP1_TOO_SHORT without buffering header bits, but we will still
|
|
|
|
|
+ * set BCF=1, which is wrong. Avoid complications and return early.
|
|
|
|
|
+ */
|
|
|
|
|
+ if (strm->avail_out == 0) {
|
|
|
|
|
+ *result = need_more;
|
|
|
|
|
+ return 1;
|
|
|
|
|
+ }
|
|
|
|
|
+
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ /* The caller gave us too much data. Pass only one block worth of
|
|
|
|
|
+ * uncompressed data to DFLTCC and mask the rest, so that on the next
|
|
|
|
|
+ * iteration we start a new block.
|
|
|
|
|
+ */
|
|
|
|
|
+ if (no_flush && strm->avail_in > dfltcc_state->block_size) {
|
|
|
|
|
+ masked_avail_in += (strm->avail_in - dfltcc_state->block_size);
|
|
|
|
|
+ strm->avail_in = dfltcc_state->block_size;
|
|
|
|
|
+ }
|
|
|
|
|
+
|
|
|
|
|
+ /* When we have an open non-BFINAL deflate block and caller indicates that
|
|
|
|
|
+ * the stream is ending, we need to close an open deflate block and open a
|
|
|
|
|
+ * BFINAL one.
|
|
|
|
|
+ */
|
|
|
|
|
+ need_empty_block = flush == Z_FINISH && param->bcf && !param->bhf;
|
|
|
|
|
+
|
|
|
|
|
+ /* Translate stream to parameter block */
|
|
|
|
|
+ param->cvt = state->wrap == 2 ? CVT_CRC32 : CVT_ADLER32;
|
|
|
|
|
+ if (!no_flush)
|
|
|
|
|
+ /* We need to close a block. Always do this in software - when there is
|
2022-06-22 17:27:43 +00:00
|
|
|
+ * no input data, the hardware will not honor BCC. */
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ soft_bcc = 1;
|
|
|
|
|
+ if (flush == Z_FINISH && !param->bcf)
|
|
|
|
|
+ /* We are about to open a BFINAL block, set Block Header Final bit
|
|
|
|
|
+ * until the stream ends.
|
|
|
|
|
+ */
|
|
|
|
|
+ param->bhf = 1;
|
|
|
|
|
+ /* DFLTCC-CMPR will write to next_out, so make sure that buffers with
|
|
|
|
|
+ * higher precedence are empty.
|
|
|
|
|
+ */
|
|
|
|
|
+ Assert(state->pending == 0, "There must be no pending bytes");
|
|
|
|
|
+ Assert(state->bi_valid < 8, "There must be less than 8 pending bits");
|
|
|
|
|
+ param->sbb = (unsigned int)state->bi_valid;
|
|
|
|
|
+ if (param->sbb > 0)
|
|
|
|
|
+ *strm->next_out = (Bytef)state->bi_buf;
|
2022-06-22 17:27:43 +00:00
|
|
|
+ /* Honor history and check value */
|
|
|
|
|
+ param->nt = 0;
|
2023-01-11 11:15:11 +00:00
|
|
|
+ if (state->wrap == 1)
|
|
|
|
|
+ param->cv = strm->adler;
|
|
|
|
|
+ else if (state->wrap == 2)
|
|
|
|
|
+ param->cv = ZSWAP32(strm->adler);
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+
|
|
|
|
|
+ /* When opening a block, choose a Huffman-Table Type */
|
|
|
|
|
+ if (!param->bcf) {
|
|
|
|
|
+ if (state->strategy == Z_FIXED ||
|
|
|
|
|
+ (strm->total_in == 0 && dfltcc_state->block_threshold > 0))
|
|
|
|
|
+ param->htt = HTT_FIXED;
|
|
|
|
|
+ else {
|
|
|
|
|
+ param->htt = HTT_DYNAMIC;
|
|
|
|
|
+ dfltcc_gdht(strm);
|
|
|
|
|
+ }
|
|
|
|
|
+ }
|
|
|
|
|
+
|
|
|
|
|
+ /* Deflate */
|
|
|
|
|
+ do {
|
|
|
|
|
+ cc = dfltcc_cmpr(strm);
|
|
|
|
|
+ if (strm->avail_in < 4096 && masked_avail_in > 0)
|
|
|
|
|
+ /* We are about to call DFLTCC with a small input buffer, which is
|
|
|
|
|
+ * inefficient. Since there is masked data, there will be at least
|
|
|
|
|
+ * one more DFLTCC call, so skip the current one and make the next
|
|
|
|
|
+ * one handle more data.
|
|
|
|
|
+ */
|
|
|
|
|
+ break;
|
|
|
|
|
+ } while (cc == DFLTCC_CC_AGAIN);
|
|
|
|
|
+
|
|
|
|
|
+ /* Translate parameter block to stream */
|
|
|
|
|
+ strm->msg = oesc_msg(dfltcc_state->msg, param->oesc);
|
|
|
|
|
+ state->bi_valid = param->sbb;
|
|
|
|
|
+ if (state->bi_valid == 0)
|
|
|
|
|
+ state->bi_buf = 0; /* Avoid accessing next_out */
|
|
|
|
|
+ else
|
|
|
|
|
+ state->bi_buf = *strm->next_out & ((1 << state->bi_valid) - 1);
|
2023-01-11 11:15:11 +00:00
|
|
|
+ if (state->wrap == 1)
|
|
|
|
|
+ strm->adler = param->cv;
|
|
|
|
|
+ else if (state->wrap == 2)
|
|
|
|
|
+ strm->adler = ZSWAP32(param->cv);
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+
|
|
|
|
|
+ /* Unmask the input data */
|
|
|
|
|
+ strm->avail_in += masked_avail_in;
|
|
|
|
|
+ masked_avail_in = 0;
|
|
|
|
|
+
|
|
|
|
|
+ /* If we encounter an error, it means there is a bug in DFLTCC call */
|
|
|
|
|
+ Assert(cc != DFLTCC_CC_OP2_CORRUPT || param->oesc == 0, "BUG");
|
|
|
|
|
+
|
|
|
|
|
+ /* Update Block-Continuation Flag. It will be used to check whether to call
|
|
|
|
|
+ * GDHT the next time.
|
|
|
|
|
+ */
|
|
|
|
|
+ if (cc == DFLTCC_CC_OK) {
|
|
|
|
|
+ if (soft_bcc) {
|
|
|
|
|
+ send_eobs(strm, param);
|
|
|
|
|
+ param->bcf = 0;
|
|
|
|
|
+ dfltcc_state->block_threshold =
|
|
|
|
|
+ strm->total_in + dfltcc_state->block_size;
|
|
|
|
|
+ } else
|
|
|
|
|
+ param->bcf = 1;
|
|
|
|
|
+ if (flush == Z_FINISH) {
|
|
|
|
|
+ if (need_empty_block)
|
|
|
|
|
+ /* Make the current deflate() call also close the stream */
|
|
|
|
|
+ return 0;
|
|
|
|
|
+ else {
|
|
|
|
|
+ bi_windup(state);
|
|
|
|
|
+ *result = finish_done;
|
|
|
|
|
+ }
|
|
|
|
|
+ } else {
|
|
|
|
|
+ if (flush == Z_FULL_FLUSH)
|
|
|
|
|
+ param->hl = 0; /* Clear history */
|
|
|
|
|
+ *result = flush == Z_NO_FLUSH ? need_more : block_done;
|
|
|
|
|
+ }
|
|
|
|
|
+ } else {
|
|
|
|
|
+ param->bcf = 1;
|
|
|
|
|
+ *result = need_more;
|
|
|
|
|
+ }
|
|
|
|
|
+ if (strm->avail_in != 0 && strm->avail_out != 0)
|
|
|
|
|
+ goto again; /* deflate() must use all input or all output */
|
|
|
|
|
+ return 1;
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+/*
|
|
|
|
|
+ Expand.
|
|
|
|
|
+ */
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_can_inflate(strm)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+{
|
|
|
|
|
+ struct inflate_state FAR *state = (struct inflate_state FAR *)strm->state;
|
|
|
|
|
+ struct dfltcc_state FAR *dfltcc_state = GET_DFLTCC_STATE(state);
|
|
|
|
|
+
|
|
|
|
|
+ /* Unsupported hardware */
|
|
|
|
|
+ return is_bit_set(dfltcc_state->af.fns, DFLTCC_XPND) &&
|
|
|
|
|
+ is_bit_set(dfltcc_state->af.fmts, DFLTCC_FMT0);
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+local dfltcc_cc dfltcc_xpnd OF((z_streamp strm));
|
|
|
|
|
+local dfltcc_cc dfltcc_xpnd(strm)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+{
|
|
|
|
|
+ struct inflate_state FAR *state = (struct inflate_state FAR *)strm->state;
|
|
|
|
|
+ struct dfltcc_param_v0 FAR *param = &GET_DFLTCC_STATE(state)->param;
|
|
|
|
|
+ size_t avail_in = strm->avail_in;
|
|
|
|
|
+ size_t avail_out = strm->avail_out;
|
|
|
|
|
+ dfltcc_cc cc;
|
|
|
|
|
+
|
|
|
|
|
+ cc = dfltcc(DFLTCC_XPND | HBT_CIRCULAR,
|
|
|
|
|
+ param, &strm->next_out, &avail_out,
|
|
|
|
|
+ &strm->next_in, &avail_in, state->window);
|
|
|
|
|
+ strm->avail_in = avail_in;
|
|
|
|
|
+ strm->avail_out = avail_out;
|
|
|
|
|
+ return cc;
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+dfltcc_inflate_action ZLIB_INTERNAL dfltcc_inflate(strm, flush, ret)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+ int flush;
|
|
|
|
|
+ int *ret;
|
|
|
|
|
+{
|
|
|
|
|
+ struct inflate_state FAR *state = (struct inflate_state FAR *)strm->state;
|
|
|
|
|
+ struct dfltcc_state FAR *dfltcc_state = GET_DFLTCC_STATE(state);
|
|
|
|
|
+ struct dfltcc_param_v0 FAR *param = &dfltcc_state->param;
|
|
|
|
|
+ dfltcc_cc cc;
|
|
|
|
|
+
|
|
|
|
|
+ if (flush == Z_BLOCK || flush == Z_TREES) {
|
|
|
|
|
+ /* DFLTCC does not support stopping on block boundaries */
|
|
|
|
|
+ if (dfltcc_inflate_disable(strm)) {
|
|
|
|
|
+ *ret = Z_STREAM_ERROR;
|
|
|
|
|
+ return DFLTCC_INFLATE_BREAK;
|
|
|
|
|
+ } else
|
|
|
|
|
+ return DFLTCC_INFLATE_SOFTWARE;
|
|
|
|
|
+ }
|
|
|
|
|
+
|
|
|
|
|
+ if (state->last) {
|
|
|
|
|
+ if (state->bits != 0) {
|
|
|
|
|
+ strm->next_in++;
|
|
|
|
|
+ strm->avail_in--;
|
|
|
|
|
+ state->bits = 0;
|
|
|
|
|
+ }
|
|
|
|
|
+ state->mode = CHECK;
|
|
|
|
|
+ return DFLTCC_INFLATE_CONTINUE;
|
|
|
|
|
+ }
|
|
|
|
|
+
|
|
|
|
|
+ if (strm->avail_in == 0 && !param->cf)
|
|
|
|
|
+ return DFLTCC_INFLATE_BREAK;
|
|
|
|
|
+
|
|
|
|
|
+ if (inflate_ensure_window(state)) {
|
|
|
|
|
+ state->mode = MEM;
|
|
|
|
|
+ return DFLTCC_INFLATE_CONTINUE;
|
|
|
|
|
+ }
|
|
|
|
|
+
|
|
|
|
|
+ /* Translate stream to parameter block */
|
2023-01-11 11:15:11 +00:00
|
|
|
+ param->cvt = ((state->wrap & 4) && state->flags) ? CVT_CRC32 : CVT_ADLER32;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ param->sbb = state->bits;
|
|
|
|
|
+ if (param->hl)
|
|
|
|
|
+ param->nt = 0; /* Honor history for the first block */
|
2023-01-11 11:15:11 +00:00
|
|
|
+ if (state->wrap & 4)
|
|
|
|
|
+ param->cv = state->flags ? ZSWAP32(state->check) : state->check;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+
|
|
|
|
|
+ /* Inflate */
|
|
|
|
|
+ do {
|
|
|
|
|
+ cc = dfltcc_xpnd(strm);
|
|
|
|
|
+ } while (cc == DFLTCC_CC_AGAIN);
|
|
|
|
|
+
|
|
|
|
|
+ /* Translate parameter block to stream */
|
|
|
|
|
+ strm->msg = oesc_msg(dfltcc_state->msg, param->oesc);
|
|
|
|
|
+ state->last = cc == DFLTCC_CC_OK;
|
|
|
|
|
+ state->bits = param->sbb;
|
2023-01-11 11:15:11 +00:00
|
|
|
+ if (state->wrap & 4)
|
|
|
|
|
+ strm->adler = state->check = state->flags ?
|
|
|
|
|
+ ZSWAP32(param->cv) : param->cv;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ if (cc == DFLTCC_CC_OP2_CORRUPT && param->oesc != 0) {
|
|
|
|
|
+ /* Report an error if stream is corrupted */
|
|
|
|
|
+ state->mode = BAD;
|
|
|
|
|
+ return DFLTCC_INFLATE_CONTINUE;
|
|
|
|
|
+ }
|
|
|
|
|
+ state->mode = TYPEDO;
|
|
|
|
|
+ /* Break if operands are exhausted, otherwise continue looping */
|
|
|
|
|
+ return (cc == DFLTCC_CC_OP1_TOO_SHORT || cc == DFLTCC_CC_OP2_TOO_SHORT) ?
|
|
|
|
|
+ DFLTCC_INFLATE_BREAK : DFLTCC_INFLATE_CONTINUE;
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_was_inflate_used(strm)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+{
|
|
|
|
|
+ struct inflate_state FAR *state = (struct inflate_state FAR *)strm->state;
|
|
|
|
|
+ struct dfltcc_param_v0 FAR *param = &GET_DFLTCC_STATE(state)->param;
|
|
|
|
|
+
|
|
|
|
|
+ return !param->nt;
|
|
|
|
|
+}
|
|
|
|
|
+
|
2023-01-11 11:15:11 +00:00
|
|
|
+/*
|
|
|
|
|
+ Rotates a circular buffer.
|
|
|
|
|
+ The implementation is based on https://cplusplus.com/reference/algorithm/rotate/
|
|
|
|
|
+ */
|
|
|
|
|
+local void rotate OF((Bytef *start, Bytef *pivot, Bytef *end));
|
|
|
|
|
+local void rotate(start, pivot, end)
|
|
|
|
|
+ Bytef *start;
|
|
|
|
|
+ Bytef *pivot;
|
|
|
|
|
+ Bytef *end;
|
|
|
|
|
+{
|
|
|
|
|
+ Bytef *p = pivot;
|
|
|
|
|
+ Bytef tmp;
|
|
|
|
|
+
|
|
|
|
|
+ while (p != start) {
|
|
|
|
|
+ tmp = *start;
|
|
|
|
|
+ *start = *p;
|
|
|
|
|
+ *p = tmp;
|
|
|
|
|
+
|
|
|
|
|
+ start++;
|
|
|
|
|
+ p++;
|
|
|
|
|
+
|
|
|
|
|
+ if (p == end)
|
|
|
|
|
+ p = pivot;
|
|
|
|
|
+ else if (start == pivot)
|
|
|
|
|
+ pivot = p;
|
|
|
|
|
+ }
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+#define MIN(x, y) ({ \
|
|
|
|
|
+ typeof(x) _x = (x); \
|
|
|
|
|
+ typeof(y) _y = (y); \
|
|
|
|
|
+ _x < _y ? _x : _y; \
|
|
|
|
|
+})
|
|
|
|
|
+
|
|
|
|
|
+#define MAX(x, y) ({ \
|
|
|
|
|
+ typeof(x) _x = (x); \
|
|
|
|
|
+ typeof(y) _y = (y); \
|
|
|
|
|
+ _x > _y ? _x : _y; \
|
|
|
|
|
+})
|
|
|
|
|
+
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+int ZLIB_INTERNAL dfltcc_inflate_disable(strm)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+{
|
|
|
|
|
+ struct inflate_state FAR *state = (struct inflate_state FAR *)strm->state;
|
|
|
|
|
+ struct dfltcc_state FAR *dfltcc_state = GET_DFLTCC_STATE(state);
|
2023-01-11 11:15:11 +00:00
|
|
|
+ struct dfltcc_param_v0 *param = &dfltcc_state->param;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+
|
|
|
|
|
+ if (!dfltcc_can_inflate(strm))
|
|
|
|
|
+ return 0;
|
|
|
|
|
+ if (dfltcc_was_inflate_used(strm))
|
|
|
|
|
+ /* DFLTCC has already decompressed some data. Since there is not
|
|
|
|
|
+ * enough information to resume decompression in software, the call
|
|
|
|
|
+ * must fail.
|
|
|
|
|
+ */
|
|
|
|
|
+ return 1;
|
|
|
|
|
+ /* DFLTCC was not used yet - decompress in software */
|
|
|
|
|
+ memset(&dfltcc_state->af, 0, sizeof(dfltcc_state->af));
|
2023-01-11 11:15:11 +00:00
|
|
|
+ /* Convert the window from the hardware to the software format */
|
|
|
|
|
+ rotate(state->window, state->window + param->ho, state->window + HB_SIZE);
|
|
|
|
|
+ state->whave = state->wnext = MIN(param->hl, state->wsize);
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ return 0;
|
|
|
|
|
+}
|
|
|
|
|
+
|
2022-06-22 17:27:43 +00:00
|
|
|
+local int env_dfltcc_disabled;
|
|
|
|
|
+local int env_source_date_epoch;
|
|
|
|
|
+local unsigned long env_level_mask;
|
|
|
|
|
+local unsigned long env_block_size;
|
|
|
|
|
+local unsigned long env_block_threshold;
|
|
|
|
|
+local unsigned long env_dht_threshold;
|
|
|
|
|
+local unsigned long env_ribm;
|
|
|
|
|
+local uint64_t cpu_facilities[(DFLTCC_FACILITY / 64) + 1];
|
|
|
|
|
+local struct dfltcc_qaf_param cpu_af __attribute__((aligned(8)));
|
|
|
|
|
+
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+local inline int is_dfltcc_enabled OF((void));
|
|
|
|
|
+local inline int is_dfltcc_enabled(void)
|
|
|
|
|
+{
|
2022-06-22 17:27:43 +00:00
|
|
|
+ if (env_dfltcc_disabled)
|
|
|
|
|
+ /* User has explicitly disabled DFLTCC. */
|
|
|
|
|
+ return 0;
|
|
|
|
|
+
|
|
|
|
|
+ return is_bit_set((const char *)cpu_facilities, DFLTCC_FACILITY);
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+local unsigned long xstrtoul OF((const char *s, unsigned long _default));
|
|
|
|
|
+local unsigned long xstrtoul(s, _default)
|
|
|
|
|
+ const char *s;
|
|
|
|
|
+ unsigned long _default;
|
|
|
|
|
+{
|
|
|
|
|
+ char *endptr;
|
|
|
|
|
+ unsigned long result;
|
|
|
|
|
+
|
|
|
|
|
+ if (!(s && *s))
|
|
|
|
|
+ return _default;
|
|
|
|
|
+ errno = 0;
|
|
|
|
|
+ result = strtoul(s, &endptr, 0);
|
|
|
|
|
+ return (errno || *endptr) ? _default : result;
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+__attribute__((constructor)) local void init_globals OF((void));
|
|
|
|
|
+__attribute__((constructor)) local void init_globals(void)
|
|
|
|
|
+{
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ const char *env;
|
|
|
|
|
+ register char r0 __asm__("r0");
|
|
|
|
|
+
|
|
|
|
|
+ env = secure_getenv("DFLTCC");
|
2022-06-22 17:27:43 +00:00
|
|
|
+ env_dfltcc_disabled = env && !strcmp(env, "0");
|
|
|
|
|
+
|
|
|
|
|
+ env = secure_getenv("SOURCE_DATE_EPOCH");
|
|
|
|
|
+ env_source_date_epoch = !!env;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+
|
2022-06-22 17:27:43 +00:00
|
|
|
+#ifndef DFLTCC_LEVEL_MASK
|
|
|
|
|
+#define DFLTCC_LEVEL_MASK 0x2
|
|
|
|
|
+#endif
|
|
|
|
|
+ env_level_mask = xstrtoul(secure_getenv("DFLTCC_LEVEL_MASK"),
|
|
|
|
|
+ DFLTCC_LEVEL_MASK);
|
|
|
|
|
+
|
|
|
|
|
+#ifndef DFLTCC_BLOCK_SIZE
|
|
|
|
|
+#define DFLTCC_BLOCK_SIZE 1048576
|
|
|
|
|
+#endif
|
|
|
|
|
+ env_block_size = xstrtoul(secure_getenv("DFLTCC_BLOCK_SIZE"),
|
|
|
|
|
+ DFLTCC_BLOCK_SIZE);
|
|
|
|
|
+
|
|
|
|
|
+#ifndef DFLTCC_FIRST_FHT_BLOCK_SIZE
|
|
|
|
|
+#define DFLTCC_FIRST_FHT_BLOCK_SIZE 4096
|
|
|
|
|
+#endif
|
|
|
|
|
+ env_block_threshold = xstrtoul(secure_getenv("DFLTCC_FIRST_FHT_BLOCK_SIZE"),
|
|
|
|
|
+ DFLTCC_FIRST_FHT_BLOCK_SIZE);
|
|
|
|
|
+
|
|
|
|
|
+#ifndef DFLTCC_DHT_MIN_SAMPLE_SIZE
|
|
|
|
|
+#define DFLTCC_DHT_MIN_SAMPLE_SIZE 4096
|
|
|
|
|
+#endif
|
|
|
|
|
+ env_dht_threshold = xstrtoul(secure_getenv("DFLTCC_DHT_MIN_SAMPLE_SIZE"),
|
|
|
|
|
+ DFLTCC_DHT_MIN_SAMPLE_SIZE);
|
|
|
|
|
+
|
|
|
|
|
+#ifndef DFLTCC_RIBM
|
|
|
|
|
+#define DFLTCC_RIBM 0
|
|
|
|
|
+#endif
|
|
|
|
|
+ env_ribm = xstrtoul(secure_getenv("DFLTCC_RIBM"), DFLTCC_RIBM);
|
|
|
|
|
+
|
|
|
|
|
+ memset(cpu_facilities, 0, sizeof(cpu_facilities));
|
|
|
|
|
+ r0 = sizeof(cpu_facilities) / sizeof(cpu_facilities[0]) - 1;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ /* STFLE is supported since z9-109 and only in z/Architecture mode. When
|
|
|
|
|
+ * compiling with -m31, gcc defaults to ESA mode, however, since the kernel
|
|
|
|
|
+ * is 64-bit, it's always z/Architecture mode at runtime.
|
|
|
|
|
+ */
|
2022-06-22 17:27:43 +00:00
|
|
|
+ __asm__ volatile(
|
|
|
|
|
+#ifndef __clang__
|
|
|
|
|
+ ".machinemode push\n"
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ ".machinemode zarch\n"
|
2022-06-22 17:27:43 +00:00
|
|
|
+#endif
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ "stfle %[facilities]\n"
|
2022-06-22 17:27:43 +00:00
|
|
|
+#ifndef __clang__
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ ".machinemode pop\n"
|
2022-06-22 17:27:43 +00:00
|
|
|
+#endif
|
|
|
|
|
+ : [facilities] "=Q" (cpu_facilities)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ , [r0] "+r" (r0)
|
|
|
|
|
+ :
|
|
|
|
|
+ : "cc");
|
2022-06-22 17:27:43 +00:00
|
|
|
+
|
|
|
|
|
+ /* Initialize available functions */
|
|
|
|
|
+ if (is_dfltcc_enabled())
|
|
|
|
|
+ dfltcc(DFLTCC_QAF, &cpu_af, NULL, NULL, NULL, NULL, NULL);
|
|
|
|
|
+ else
|
|
|
|
|
+ memset(&cpu_af, 0, sizeof(cpu_af));
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+}
|
|
|
|
|
+
|
2022-06-22 17:27:43 +00:00
|
|
|
+/*
|
|
|
|
|
+ Memory management.
|
|
|
|
|
+
|
|
|
|
|
+ DFLTCC requires parameter blocks and window to be aligned. zlib allows
|
|
|
|
|
+ users to specify their own allocation functions, so using e.g.
|
|
|
|
|
+ `posix_memalign' is not an option. Thus, we overallocate and take the
|
|
|
|
|
+ aligned portion of the buffer.
|
|
|
|
|
+*/
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+void ZLIB_INTERNAL dfltcc_reset(strm, size)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+ uInt size;
|
|
|
|
|
+{
|
|
|
|
|
+ struct dfltcc_state *dfltcc_state =
|
|
|
|
|
+ (struct dfltcc_state *)((char FAR *)strm->state + ALIGN_UP(size, 8));
|
|
|
|
|
+
|
2022-06-22 17:27:43 +00:00
|
|
|
+ memcpy(&dfltcc_state->af, &cpu_af, sizeof(dfltcc_state->af));
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+
|
2022-06-22 17:27:43 +00:00
|
|
|
+ if (env_source_date_epoch)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ /* User needs reproducible results, but the output of DFLTCC_CMPR
|
|
|
|
|
+ * depends on buffers' page offsets.
|
|
|
|
|
+ */
|
|
|
|
|
+ clear_bit(dfltcc_state->af.fns, DFLTCC_CMPR);
|
|
|
|
|
+
|
|
|
|
|
+ /* Initialize parameter block */
|
|
|
|
|
+ memset(&dfltcc_state->param, 0, sizeof(dfltcc_state->param));
|
|
|
|
|
+ dfltcc_state->param.nt = 1;
|
|
|
|
|
+
|
|
|
|
|
+ /* Initialize tuning parameters */
|
2022-06-22 17:27:43 +00:00
|
|
|
+ dfltcc_state->level_mask = env_level_mask;
|
|
|
|
|
+ dfltcc_state->block_size = env_block_size;
|
|
|
|
|
+ dfltcc_state->block_threshold = env_block_threshold;
|
|
|
|
|
+ dfltcc_state->dht_threshold = env_dht_threshold;
|
|
|
|
|
+ dfltcc_state->param.ribm = env_ribm;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+voidpf ZLIB_INTERNAL dfltcc_alloc_state(strm, items, size)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+ uInt items;
|
|
|
|
|
+ uInt size;
|
|
|
|
|
+{
|
|
|
|
|
+ return ZALLOC(strm,
|
|
|
|
|
+ ALIGN_UP(items * size, 8) + sizeof(struct dfltcc_state),
|
|
|
|
|
+ sizeof(unsigned char));
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+void ZLIB_INTERNAL dfltcc_copy_state(dst, src, size)
|
|
|
|
|
+ voidpf dst;
|
|
|
|
|
+ const voidpf src;
|
|
|
|
|
+ uInt size;
|
|
|
|
|
+{
|
|
|
|
|
+ zmemcpy(dst, src, ALIGN_UP(size, 8) + sizeof(struct dfltcc_state));
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+static const int PAGE_ALIGN = 0x1000;
|
|
|
|
|
+
|
|
|
|
|
+voidpf ZLIB_INTERNAL dfltcc_alloc_window(strm, items, size)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+ uInt items;
|
|
|
|
|
+ uInt size;
|
|
|
|
|
+{
|
|
|
|
|
+ voidpf p, w;
|
|
|
|
|
+
|
|
|
|
|
+ /* To simplify freeing, we store the pointer to the allocated buffer right
|
2023-01-11 11:15:11 +00:00
|
|
|
+ * before the window. Note that DFLTCC always uses HB_SIZE bytes.
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ */
|
2023-01-11 11:15:11 +00:00
|
|
|
+ p = ZALLOC(strm, sizeof(voidpf) + MAX(items * size, HB_SIZE) + PAGE_ALIGN,
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ sizeof(unsigned char));
|
|
|
|
|
+ if (p == NULL)
|
|
|
|
|
+ return NULL;
|
|
|
|
|
+ w = ALIGN_UP((char FAR *)p + sizeof(voidpf), PAGE_ALIGN);
|
|
|
|
|
+ *(voidpf *)((char FAR *)w - sizeof(voidpf)) = p;
|
|
|
|
|
+ return w;
|
|
|
|
|
+}
|
|
|
|
|
+
|
2023-01-11 11:15:11 +00:00
|
|
|
+void ZLIB_INTERNAL dfltcc_copy_window(dest, src, n)
|
|
|
|
|
+ void *dest;
|
|
|
|
|
+ const void *src;
|
|
|
|
|
+ size_t n;
|
|
|
|
|
+{
|
|
|
|
|
+ memcpy(dest, src, MAX(n, HB_SIZE));
|
|
|
|
|
+}
|
|
|
|
|
+
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+void ZLIB_INTERNAL dfltcc_free_window(strm, w)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+ voidpf w;
|
|
|
|
|
+{
|
|
|
|
|
+ if (w)
|
|
|
|
|
+ ZFREE(strm, *(voidpf *)((unsigned char FAR *)w - sizeof(voidpf)));
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+/*
|
|
|
|
|
+ Switching between hardware and software compression.
|
2022-06-22 17:27:43 +00:00
|
|
|
+
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ DFLTCC does not support all zlib settings, e.g. generation of non-compressed
|
|
|
|
|
+ blocks or alternative window sizes. When such settings are applied on the
|
|
|
|
|
+ fly with deflateParams, we need to convert between hardware and software
|
|
|
|
|
+ window formats.
|
|
|
|
|
+*/
|
2022-06-22 17:27:43 +00:00
|
|
|
+int ZLIB_INTERNAL dfltcc_deflate_params(strm, level, strategy, flush)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ z_streamp strm;
|
|
|
|
|
+ int level;
|
|
|
|
|
+ int strategy;
|
2022-06-22 17:27:43 +00:00
|
|
|
+ int *flush;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+{
|
|
|
|
|
+ deflate_state FAR *state = (deflate_state FAR *)strm->state;
|
|
|
|
|
+ struct dfltcc_state FAR *dfltcc_state = GET_DFLTCC_STATE(state);
|
|
|
|
|
+ struct dfltcc_param_v0 FAR *param = &dfltcc_state->param;
|
|
|
|
|
+ int could_deflate = dfltcc_can_deflate(strm);
|
2022-06-22 17:27:43 +00:00
|
|
|
+ int can_deflate = dfltcc_can_deflate_with_params(strm,
|
|
|
|
|
+ level,
|
|
|
|
|
+ state->w_bits,
|
|
|
|
|
+ strategy);
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+
|
|
|
|
|
+ if (can_deflate == could_deflate)
|
|
|
|
|
+ /* We continue to work in the same mode - no changes needed */
|
|
|
|
|
+ return Z_OK;
|
|
|
|
|
+
|
|
|
|
|
+ if (strm->total_in == 0 && param->nt == 1 && param->hl == 0)
|
|
|
|
|
+ /* DFLTCC was not used yet - no changes needed */
|
|
|
|
|
+ return Z_OK;
|
|
|
|
|
+
|
2022-06-22 17:27:43 +00:00
|
|
|
+ /* For now, do not convert between window formats - simply get rid of the
|
|
|
|
|
+ * old data instead.
|
|
|
|
|
+ */
|
|
|
|
|
+ *flush = Z_FULL_FLUSH;
|
|
|
|
|
+ return Z_OK;
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_deflate_done(strm, flush)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+ int flush;
|
|
|
|
|
+{
|
|
|
|
|
+ deflate_state FAR *state = (deflate_state FAR *)strm->state;
|
|
|
|
|
+ struct dfltcc_state FAR *dfltcc_state = GET_DFLTCC_STATE(state);
|
|
|
|
|
+ struct dfltcc_param_v0 FAR *param = &dfltcc_state->param;
|
|
|
|
|
+
|
|
|
|
|
+ /* When deflate(Z_FULL_FLUSH) is called with small avail_out, it might
|
|
|
|
|
+ * close the block without resetting the compression state. Detect this
|
|
|
|
|
+ * situation and return that deflation is not done.
|
|
|
|
|
+ */
|
|
|
|
|
+ if (flush == Z_FULL_FLUSH && strm->avail_out == 0)
|
|
|
|
|
+ return 0;
|
|
|
|
|
+
|
|
|
|
|
+ /* Return that deflation is not done if DFLTCC is used and either it
|
|
|
|
|
+ * buffered some data (Continuation Flag is set), or has not written EOBS
|
|
|
|
|
+ * yet (Block-Continuation Flag is set).
|
|
|
|
|
+ */
|
|
|
|
|
+ return !dfltcc_can_deflate(strm) || (!param->cf && !param->bcf);
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+/*
|
|
|
|
|
+ Preloading history.
|
|
|
|
|
+*/
|
|
|
|
|
+local void append_history OF((struct dfltcc_param_v0 FAR *param,
|
|
|
|
|
+ Bytef *history,
|
|
|
|
|
+ const Bytef *buf,
|
|
|
|
|
+ uInt count));
|
|
|
|
|
+local void append_history(param, history, buf, count)
|
|
|
|
|
+ struct dfltcc_param_v0 FAR *param;
|
|
|
|
|
+ Bytef *history;
|
|
|
|
|
+ const Bytef *buf;
|
|
|
|
|
+ uInt count;
|
|
|
|
|
+{
|
|
|
|
|
+ size_t offset;
|
|
|
|
|
+ size_t n;
|
|
|
|
|
+
|
|
|
|
|
+ /* Do not use more than 32K */
|
|
|
|
|
+ if (count > HB_SIZE) {
|
|
|
|
|
+ buf += count - HB_SIZE;
|
|
|
|
|
+ count = HB_SIZE;
|
|
|
|
|
+ }
|
|
|
|
|
+ offset = (param->ho + param->hl) % HB_SIZE;
|
|
|
|
|
+ if (offset + count <= HB_SIZE)
|
|
|
|
|
+ /* Circular history buffer does not wrap - copy one chunk */
|
|
|
|
|
+ zmemcpy(history + offset, buf, count);
|
|
|
|
|
+ else {
|
|
|
|
|
+ /* Circular history buffer wraps - copy two chunks */
|
|
|
|
|
+ n = HB_SIZE - offset;
|
|
|
|
|
+ zmemcpy(history + offset, buf, n);
|
|
|
|
|
+ zmemcpy(history, buf + n, count - n);
|
|
|
|
|
+ }
|
|
|
|
|
+ n = param->hl + count;
|
|
|
|
|
+ if (n <= HB_SIZE)
|
|
|
|
|
+ /* All history fits into buffer - no need to discard anything */
|
|
|
|
|
+ param->hl = n;
|
|
|
|
|
+ else {
|
|
|
|
|
+ /* History does not fit into buffer - discard extra bytes */
|
|
|
|
|
+ param->ho = (param->ho + (n - HB_SIZE)) % HB_SIZE;
|
|
|
|
|
+ param->hl = HB_SIZE;
|
|
|
|
|
+ }
|
|
|
|
|
+}
|
|
|
|
|
+
|
2023-01-11 11:15:11 +00:00
|
|
|
+local void get_history OF((struct dfltcc_param_v0 FAR *param,
|
|
|
|
|
+ const Bytef *history,
|
|
|
|
|
+ Bytef *buf));
|
|
|
|
|
+local void get_history(param, history, buf)
|
|
|
|
|
+ struct dfltcc_param_v0 FAR *param;
|
|
|
|
|
+ const Bytef *history;
|
|
|
|
|
+ Bytef *buf;
|
|
|
|
|
+{
|
|
|
|
|
+ if (param->ho + param->hl <= HB_SIZE)
|
|
|
|
|
+ /* Circular history buffer does not wrap - copy one chunk */
|
|
|
|
|
+ memcpy(buf, history + param->ho, param->hl);
|
|
|
|
|
+ else {
|
|
|
|
|
+ /* Circular history buffer wraps - copy two chunks */
|
|
|
|
|
+ memcpy(buf, history + param->ho, HB_SIZE - param->ho);
|
|
|
|
|
+ memcpy(buf + HB_SIZE - param->ho, history, param->ho + param->hl - HB_SIZE);
|
|
|
|
|
+ }
|
|
|
|
|
+}
|
|
|
|
|
+
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+int ZLIB_INTERNAL dfltcc_deflate_set_dictionary(strm, dictionary, dict_length)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+ const Bytef *dictionary;
|
|
|
|
|
+ uInt dict_length;
|
|
|
|
|
+{
|
|
|
|
|
+ deflate_state FAR *state = (deflate_state FAR *)strm->state;
|
|
|
|
|
+ struct dfltcc_state FAR *dfltcc_state = GET_DFLTCC_STATE(state);
|
|
|
|
|
+ struct dfltcc_param_v0 FAR *param = &dfltcc_state->param;
|
|
|
|
|
+
|
|
|
|
|
+ append_history(param, state->window, dictionary, dict_length);
|
|
|
|
|
+ state->strstart = 1; /* Add FDICT to zlib header */
|
2022-06-22 17:27:43 +00:00
|
|
|
+ state->block_start = state->strstart; /* Make deflate_stored happy */
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ return Z_OK;
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_deflate_get_dictionary(strm, dictionary, dict_length)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+ Bytef *dictionary;
|
|
|
|
|
+ uInt *dict_length;
|
|
|
|
|
+{
|
|
|
|
|
+ deflate_state FAR *state = (deflate_state FAR *)strm->state;
|
|
|
|
|
+ struct dfltcc_state FAR *dfltcc_state = GET_DFLTCC_STATE(state);
|
|
|
|
|
+ struct dfltcc_param_v0 FAR *param = &dfltcc_state->param;
|
|
|
|
|
+
|
2023-01-11 11:15:11 +00:00
|
|
|
+ if (dictionary)
|
|
|
|
|
+ get_history(param, state->window, dictionary);
|
|
|
|
|
+ if (dict_length)
|
|
|
|
|
+ *dict_length = param->hl;
|
|
|
|
|
+ return Z_OK;
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_inflate_set_dictionary(strm, dictionary, dict_length)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+ const Bytef *dictionary;
|
|
|
|
|
+ uInt dict_length;
|
|
|
|
|
+{
|
|
|
|
|
+ struct inflate_state *state = (struct inflate_state *)strm->state;
|
|
|
|
|
+ struct dfltcc_state *dfltcc_state = GET_DFLTCC_STATE(state);
|
|
|
|
|
+ struct dfltcc_param_v0 *param = &dfltcc_state->param;
|
|
|
|
|
+
|
|
|
|
|
+ if (inflate_ensure_window(state)) {
|
|
|
|
|
+ state->mode = MEM;
|
|
|
|
|
+ return Z_MEM_ERROR;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ }
|
2023-01-11 11:15:11 +00:00
|
|
|
+
|
|
|
|
|
+ append_history(param, state->window, dictionary, dict_length);
|
|
|
|
|
+ state->havedict = 1;
|
|
|
|
|
+ return Z_OK;
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_inflate_get_dictionary(strm, dictionary, dict_length)
|
|
|
|
|
+ z_streamp strm;
|
|
|
|
|
+ Bytef *dictionary;
|
|
|
|
|
+ uInt *dict_length;
|
|
|
|
|
+{
|
|
|
|
|
+ struct inflate_state *state = (struct inflate_state *)strm->state;
|
|
|
|
|
+ struct dfltcc_state *dfltcc_state = GET_DFLTCC_STATE(state);
|
|
|
|
|
+ struct dfltcc_param_v0 *param = &dfltcc_state->param;
|
|
|
|
|
+
|
|
|
|
|
+ if (dictionary && state->window)
|
|
|
|
|
+ get_history(param, state->window, dictionary);
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ if (dict_length)
|
|
|
|
|
+ *dict_length = param->hl;
|
|
|
|
|
+ return Z_OK;
|
|
|
|
|
+}
|
|
|
|
|
diff --git a/contrib/s390/dfltcc.h b/contrib/s390/dfltcc.h
|
|
|
|
|
new file mode 100644
|
2023-01-11 11:15:11 +00:00
|
|
|
index 0000000..be28b8a
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
--- /dev/null
|
|
|
|
|
+++ b/contrib/s390/dfltcc.h
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -0,0 +1,100 @@
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+#ifndef DFLTCC_H
|
|
|
|
|
+#define DFLTCC_H
|
|
|
|
|
+
|
|
|
|
|
+#include "../../zlib.h"
|
|
|
|
|
+#include "../../zutil.h"
|
|
|
|
|
+
|
|
|
|
|
+voidpf ZLIB_INTERNAL dfltcc_alloc_state OF((z_streamp strm, uInt items,
|
|
|
|
|
+ uInt size));
|
|
|
|
|
+void ZLIB_INTERNAL dfltcc_copy_state OF((voidpf dst, const voidpf src,
|
|
|
|
|
+ uInt size));
|
|
|
|
|
+void ZLIB_INTERNAL dfltcc_reset OF((z_streamp strm, uInt size));
|
|
|
|
|
+voidpf ZLIB_INTERNAL dfltcc_alloc_window OF((z_streamp strm, uInt items,
|
|
|
|
|
+ uInt size));
|
2023-01-11 11:15:11 +00:00
|
|
|
+void ZLIB_INTERNAL dfltcc_copy_window OF((void *dest, const void *src,
|
|
|
|
|
+ size_t n));
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+void ZLIB_INTERNAL dfltcc_free_window OF((z_streamp strm, voidpf w));
|
2022-06-22 17:27:43 +00:00
|
|
|
+#define DFLTCC_BLOCK_HEADER_BITS 3
|
|
|
|
|
+#define DFLTCC_HLITS_COUNT_BITS 5
|
|
|
|
|
+#define DFLTCC_HDISTS_COUNT_BITS 5
|
|
|
|
|
+#define DFLTCC_HCLENS_COUNT_BITS 4
|
|
|
|
|
+#define DFLTCC_MAX_HCLENS 19
|
|
|
|
|
+#define DFLTCC_HCLEN_BITS 3
|
|
|
|
|
+#define DFLTCC_MAX_HLITS 286
|
|
|
|
|
+#define DFLTCC_MAX_HDISTS 30
|
|
|
|
|
+#define DFLTCC_MAX_HLIT_HDIST_BITS 7
|
|
|
|
|
+#define DFLTCC_MAX_SYMBOL_BITS 16
|
|
|
|
|
+#define DFLTCC_MAX_EOBS_BITS 15
|
|
|
|
|
+#define DFLTCC_MAX_PADDING_BITS 7
|
|
|
|
|
+#define DEFLATE_BOUND_COMPLEN(source_len) \
|
|
|
|
|
+ ((DFLTCC_BLOCK_HEADER_BITS + \
|
|
|
|
|
+ DFLTCC_HLITS_COUNT_BITS + \
|
|
|
|
|
+ DFLTCC_HDISTS_COUNT_BITS + \
|
|
|
|
|
+ DFLTCC_HCLENS_COUNT_BITS + \
|
|
|
|
|
+ DFLTCC_MAX_HCLENS * DFLTCC_HCLEN_BITS + \
|
|
|
|
|
+ (DFLTCC_MAX_HLITS + DFLTCC_MAX_HDISTS) * DFLTCC_MAX_HLIT_HDIST_BITS + \
|
|
|
|
|
+ (source_len) * DFLTCC_MAX_SYMBOL_BITS + \
|
|
|
|
|
+ DFLTCC_MAX_EOBS_BITS + \
|
|
|
|
|
+ DFLTCC_MAX_PADDING_BITS) >> 3)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+int ZLIB_INTERNAL dfltcc_can_inflate OF((z_streamp strm));
|
|
|
|
|
+typedef enum {
|
|
|
|
|
+ DFLTCC_INFLATE_CONTINUE,
|
|
|
|
|
+ DFLTCC_INFLATE_BREAK,
|
|
|
|
|
+ DFLTCC_INFLATE_SOFTWARE,
|
|
|
|
|
+} dfltcc_inflate_action;
|
|
|
|
|
+dfltcc_inflate_action ZLIB_INTERNAL dfltcc_inflate OF((z_streamp strm,
|
|
|
|
|
+ int flush, int *ret));
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_was_inflate_used OF((z_streamp strm));
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_inflate_disable OF((z_streamp strm));
|
2023-01-11 11:15:11 +00:00
|
|
|
+int ZLIB_INTERNAL dfltcc_inflate_set_dictionary OF((z_streamp strm,
|
|
|
|
|
+ const Bytef *dictionary,
|
|
|
|
|
+ uInt dict_length));
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_inflate_get_dictionary OF((z_streamp strm,
|
|
|
|
|
+ Bytef *dictionary,
|
|
|
|
|
+ uInt* dict_length));
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+
|
|
|
|
|
+#define ZALLOC_STATE dfltcc_alloc_state
|
|
|
|
|
+#define ZFREE_STATE ZFREE
|
|
|
|
|
+#define ZCOPY_STATE dfltcc_copy_state
|
|
|
|
|
+#define ZALLOC_WINDOW dfltcc_alloc_window
|
2023-01-11 11:15:11 +00:00
|
|
|
+#define ZCOPY_WINDOW dfltcc_copy_window
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+#define ZFREE_WINDOW dfltcc_free_window
|
|
|
|
|
+#define TRY_FREE_WINDOW dfltcc_free_window
|
|
|
|
|
+#define INFLATE_RESET_KEEP_HOOK(strm) \
|
|
|
|
|
+ dfltcc_reset((strm), sizeof(struct inflate_state))
|
|
|
|
|
+#define INFLATE_PRIME_HOOK(strm, bits, value) \
|
|
|
|
|
+ do { if (dfltcc_inflate_disable((strm))) return Z_STREAM_ERROR; } while (0)
|
|
|
|
|
+#define INFLATE_TYPEDO_HOOK(strm, flush) \
|
|
|
|
|
+ if (dfltcc_can_inflate((strm))) { \
|
|
|
|
|
+ dfltcc_inflate_action action; \
|
|
|
|
|
+\
|
|
|
|
|
+ RESTORE(); \
|
|
|
|
|
+ action = dfltcc_inflate((strm), (flush), &ret); \
|
|
|
|
|
+ LOAD(); \
|
|
|
|
|
+ if (action == DFLTCC_INFLATE_CONTINUE) \
|
|
|
|
|
+ break; \
|
|
|
|
|
+ else if (action == DFLTCC_INFLATE_BREAK) \
|
|
|
|
|
+ goto inf_leave; \
|
|
|
|
|
+ }
|
|
|
|
|
+#define INFLATE_NEED_CHECKSUM(strm) (!dfltcc_can_inflate((strm)))
|
|
|
|
|
+#define INFLATE_NEED_UPDATEWINDOW(strm) (!dfltcc_can_inflate((strm)))
|
|
|
|
|
+#define INFLATE_MARK_HOOK(strm) \
|
|
|
|
|
+ do { \
|
|
|
|
|
+ if (dfltcc_was_inflate_used((strm))) return -(1L << 16); \
|
|
|
|
|
+ } while (0)
|
2022-06-22 17:27:43 +00:00
|
|
|
+#define INFLATE_SYNC_POINT_HOOK(strm) \
|
|
|
|
|
+ do { \
|
|
|
|
|
+ if (dfltcc_was_inflate_used((strm))) return Z_STREAM_ERROR; \
|
|
|
|
|
+ } while (0)
|
2023-01-11 11:15:11 +00:00
|
|
|
+#define INFLATE_SET_DICTIONARY_HOOK(strm, dict, dict_len) \
|
|
|
|
|
+ do { \
|
|
|
|
|
+ if (dfltcc_can_inflate(strm)) \
|
|
|
|
|
+ return dfltcc_inflate_set_dictionary(strm, dict, dict_len); \
|
|
|
|
|
+ } while (0)
|
|
|
|
|
+#define INFLATE_GET_DICTIONARY_HOOK(strm, dict, dict_len) \
|
|
|
|
|
+ do { \
|
|
|
|
|
+ if (dfltcc_can_inflate(strm)) \
|
|
|
|
|
+ return dfltcc_inflate_get_dictionary(strm, dict, dict_len); \
|
|
|
|
|
+ } while (0)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+
|
|
|
|
|
+#endif
|
|
|
|
|
diff --git a/contrib/s390/dfltcc_deflate.h b/contrib/s390/dfltcc_deflate.h
|
|
|
|
|
new file mode 100644
|
2022-10-17 14:31:23 +00:00
|
|
|
index 0000000..46acfc5
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
--- /dev/null
|
|
|
|
|
+++ b/contrib/s390/dfltcc_deflate.h
|
2022-06-22 17:27:43 +00:00
|
|
|
@@ -0,0 +1,55 @@
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+#ifndef DFLTCC_DEFLATE_H
|
|
|
|
|
+#define DFLTCC_DEFLATE_H
|
|
|
|
|
+
|
|
|
|
|
+#include "dfltcc.h"
|
|
|
|
|
+
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_can_deflate OF((z_streamp strm));
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_deflate OF((z_streamp strm,
|
|
|
|
|
+ int flush,
|
|
|
|
|
+ block_state *result));
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_deflate_params OF((z_streamp strm,
|
|
|
|
|
+ int level,
|
2022-06-22 17:27:43 +00:00
|
|
|
+ int strategy,
|
|
|
|
|
+ int *flush));
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_deflate_done OF((z_streamp strm, int flush));
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+int ZLIB_INTERNAL dfltcc_deflate_set_dictionary OF((z_streamp strm,
|
|
|
|
|
+ const Bytef *dictionary,
|
|
|
|
|
+ uInt dict_length));
|
|
|
|
|
+int ZLIB_INTERNAL dfltcc_deflate_get_dictionary OF((z_streamp strm,
|
|
|
|
|
+ Bytef *dictionary,
|
|
|
|
|
+ uInt* dict_length));
|
|
|
|
|
+
|
|
|
|
|
+#define DEFLATE_SET_DICTIONARY_HOOK(strm, dict, dict_len) \
|
|
|
|
|
+ do { \
|
|
|
|
|
+ if (dfltcc_can_deflate((strm))) \
|
|
|
|
|
+ return dfltcc_deflate_set_dictionary((strm), (dict), (dict_len)); \
|
|
|
|
|
+ } while (0)
|
|
|
|
|
+#define DEFLATE_GET_DICTIONARY_HOOK(strm, dict, dict_len) \
|
|
|
|
|
+ do { \
|
|
|
|
|
+ if (dfltcc_can_deflate((strm))) \
|
|
|
|
|
+ return dfltcc_deflate_get_dictionary((strm), (dict), (dict_len)); \
|
|
|
|
|
+ } while (0)
|
|
|
|
|
+#define DEFLATE_RESET_KEEP_HOOK(strm) \
|
|
|
|
|
+ dfltcc_reset((strm), sizeof(deflate_state))
|
2022-06-22 17:27:43 +00:00
|
|
|
+#define DEFLATE_PARAMS_HOOK(strm, level, strategy, hook_flush) \
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ do { \
|
|
|
|
|
+ int err; \
|
|
|
|
|
+\
|
2022-06-22 17:27:43 +00:00
|
|
|
+ err = dfltcc_deflate_params((strm), \
|
|
|
|
|
+ (level), \
|
|
|
|
|
+ (strategy), \
|
|
|
|
|
+ (hook_flush)); \
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ if (err == Z_STREAM_ERROR) \
|
|
|
|
|
+ return err; \
|
|
|
|
|
+ } while (0)
|
2022-06-22 17:27:43 +00:00
|
|
|
+#define DEFLATE_DONE dfltcc_deflate_done
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+#define DEFLATE_BOUND_ADJUST_COMPLEN(strm, complen, source_len) \
|
|
|
|
|
+ do { \
|
|
|
|
|
+ if (dfltcc_can_deflate((strm))) \
|
2022-06-22 17:27:43 +00:00
|
|
|
+ (complen) = DEFLATE_BOUND_COMPLEN(source_len); \
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ } while (0)
|
|
|
|
|
+#define DEFLATE_NEED_CONSERVATIVE_BOUND(strm) (dfltcc_can_deflate((strm)))
|
|
|
|
|
+#define DEFLATE_HOOK dfltcc_deflate
|
|
|
|
|
+#define DEFLATE_NEED_CHECKSUM(strm) (!dfltcc_can_deflate((strm)))
|
|
|
|
|
+
|
|
|
|
|
+#endif
|
|
|
|
|
diff --git a/deflate.c b/deflate.c
|
2023-01-11 11:15:11 +00:00
|
|
|
index 4a512e1..ba446d9 100644
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
--- a/deflate.c
|
|
|
|
|
+++ b/deflate.c
|
2022-06-22 17:27:43 +00:00
|
|
|
@@ -61,15 +61,30 @@ const char deflate_copyright[] =
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
/* ===========================================================================
|
|
|
|
|
- * Function prototypes.
|
|
|
|
|
+ * Architecture-specific bits.
|
|
|
|
|
*/
|
|
|
|
|
-typedef enum {
|
|
|
|
|
- need_more, /* block not completed, need more input or more output */
|
|
|
|
|
- block_done, /* block flush performed */
|
|
|
|
|
- finish_started, /* finish started, need only more output at next deflate */
|
|
|
|
|
- finish_done /* finish done, accept no more input or output */
|
|
|
|
|
-} block_state;
|
|
|
|
|
+#ifdef DFLTCC
|
|
|
|
|
+# include "contrib/s390/dfltcc_deflate.h"
|
|
|
|
|
+#else
|
|
|
|
|
+#define ZALLOC_STATE ZALLOC
|
|
|
|
|
+#define ZFREE_STATE ZFREE
|
|
|
|
|
+#define ZCOPY_STATE zmemcpy
|
|
|
|
|
+#define ZALLOC_WINDOW ZALLOC
|
|
|
|
|
+#define TRY_FREE_WINDOW TRY_FREE
|
|
|
|
|
+#define DEFLATE_SET_DICTIONARY_HOOK(strm, dict, dict_len) do {} while (0)
|
|
|
|
|
+#define DEFLATE_GET_DICTIONARY_HOOK(strm, dict, dict_len) do {} while (0)
|
|
|
|
|
+#define DEFLATE_RESET_KEEP_HOOK(strm) do {} while (0)
|
2022-06-22 17:27:43 +00:00
|
|
|
+#define DEFLATE_PARAMS_HOOK(strm, level, strategy, hook_flush) do {} while (0)
|
|
|
|
|
+#define DEFLATE_DONE(strm, flush) 1
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+#define DEFLATE_BOUND_ADJUST_COMPLEN(strm, complen, sourceLen) do {} while (0)
|
|
|
|
|
+#define DEFLATE_NEED_CONSERVATIVE_BOUND(strm) 0
|
|
|
|
|
+#define DEFLATE_HOOK(strm, flush, bstate) 0
|
|
|
|
|
+#define DEFLATE_NEED_CHECKSUM(strm) 1
|
|
|
|
|
+#endif
|
|
|
|
|
|
|
|
|
|
+/* ===========================================================================
|
|
|
|
|
+ * Function prototypes.
|
|
|
|
|
+ */
|
|
|
|
|
typedef block_state (*compress_func) OF((deflate_state *s, int flush));
|
|
|
|
|
/* Compression function. Returns the block state after the call. */
|
|
|
|
|
|
2022-06-22 17:27:43 +00:00
|
|
|
@@ -85,7 +100,6 @@ local block_state deflate_rle OF((deflate_state *s, int flush));
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
local block_state deflate_huff OF((deflate_state *s, int flush));
|
|
|
|
|
local void lm_init OF((deflate_state *s));
|
|
|
|
|
local void putShortMSB OF((deflate_state *s, uInt b));
|
|
|
|
|
-local void flush_pending OF((z_streamp strm));
|
|
|
|
|
local unsigned read_buf OF((z_streamp strm, Bytef *buf, unsigned size));
|
2022-10-17 14:31:23 +00:00
|
|
|
local uInt longest_match OF((deflate_state *s, IPos cur_match));
|
|
|
|
|
|
|
|
|
|
@@ -295,7 +309,7 @@ int ZEXPORT deflateInit2_(strm, level, method, windowBits, memLevel, strategy,
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
return Z_STREAM_ERROR;
|
|
|
|
|
}
|
|
|
|
|
if (windowBits == 8) windowBits = 9; /* until 256-byte window bug fixed */
|
|
|
|
|
- s = (deflate_state *) ZALLOC(strm, 1, sizeof(deflate_state));
|
|
|
|
|
+ s = (deflate_state *) ZALLOC_STATE(strm, 1, sizeof(deflate_state));
|
|
|
|
|
if (s == Z_NULL) return Z_MEM_ERROR;
|
|
|
|
|
strm->state = (struct internal_state FAR *)s;
|
|
|
|
|
s->strm = strm;
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -312,7 +326,7 @@ int ZEXPORT deflateInit2_(strm, level, method, windowBits, memLevel, strategy,
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
s->hash_mask = s->hash_size - 1;
|
2022-10-17 14:31:23 +00:00
|
|
|
s->hash_shift = ((s->hash_bits + MIN_MATCH-1) / MIN_MATCH);
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
|
|
|
|
- s->window = (Bytef *) ZALLOC(strm, s->w_size, 2*sizeof(Byte));
|
|
|
|
|
+ s->window = (Bytef *) ZALLOC_WINDOW(strm, s->w_size, 2*sizeof(Byte));
|
|
|
|
|
s->prev = (Posf *) ZALLOC(strm, s->w_size, sizeof(Pos));
|
|
|
|
|
s->head = (Posf *) ZALLOC(strm, s->hash_size, sizeof(Pos));
|
|
|
|
|
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -430,6 +444,7 @@ int ZEXPORT deflateSetDictionary(strm, dictionary, dictLength)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
/* when using zlib wrappers, compute Adler-32 for provided dictionary */
|
|
|
|
|
if (wrap == 1)
|
|
|
|
|
strm->adler = adler32(strm->adler, dictionary, dictLength);
|
|
|
|
|
+ DEFLATE_SET_DICTIONARY_HOOK(strm, dictionary, dictLength);
|
|
|
|
|
s->wrap = 0; /* avoid computing Adler-32 in read_buf */
|
|
|
|
|
|
|
|
|
|
/* if dictionary would fill window, just replace the history */
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -488,6 +503,7 @@ int ZEXPORT deflateGetDictionary(strm, dictionary, dictLength)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
|
|
|
|
if (deflateStateCheck(strm))
|
|
|
|
|
return Z_STREAM_ERROR;
|
|
|
|
|
+ DEFLATE_GET_DICTIONARY_HOOK(strm, dictionary, dictLength);
|
|
|
|
|
s = strm->state;
|
|
|
|
|
len = s->strstart + s->lookahead;
|
|
|
|
|
if (len > s->w_size)
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -534,6 +550,8 @@ int ZEXPORT deflateResetKeep(strm)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
|
|
|
|
_tr_init(s);
|
|
|
|
|
|
|
|
|
|
+ DEFLATE_RESET_KEEP_HOOK(strm);
|
|
|
|
|
+
|
|
|
|
|
return Z_OK;
|
|
|
|
|
}
|
|
|
|
|
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -609,6 +627,7 @@ int ZEXPORT deflateParams(strm, level, strategy)
|
2022-06-22 17:27:43 +00:00
|
|
|
{
|
|
|
|
|
deflate_state *s;
|
|
|
|
|
compress_func func;
|
|
|
|
|
+ int hook_flush = Z_NO_FLUSH;
|
|
|
|
|
|
|
|
|
|
if (deflateStateCheck(strm)) return Z_STREAM_ERROR;
|
|
|
|
|
s = strm->state;
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -621,15 +640,18 @@ int ZEXPORT deflateParams(strm, level, strategy)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
if (level < 0 || level > 9 || strategy < 0 || strategy > Z_FIXED) {
|
|
|
|
|
return Z_STREAM_ERROR;
|
|
|
|
|
}
|
2022-06-22 17:27:43 +00:00
|
|
|
+ DEFLATE_PARAMS_HOOK(strm, level, strategy, &hook_flush);
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
func = configuration_table[s->level].func;
|
|
|
|
|
|
2022-06-22 17:27:43 +00:00
|
|
|
- if ((strategy != s->strategy || func != configuration_table[level].func) &&
|
|
|
|
|
- s->last_flush != -2) {
|
|
|
|
|
+ if (((strategy != s->strategy || func != configuration_table[level].func) &&
|
|
|
|
|
+ s->last_flush != -2) || hook_flush != Z_NO_FLUSH) {
|
|
|
|
|
/* Flush the last buffer: */
|
|
|
|
|
- int err = deflate(strm, Z_BLOCK);
|
|
|
|
|
+ int flush = RANK(hook_flush) > RANK(Z_BLOCK) ? hook_flush : Z_BLOCK;
|
|
|
|
|
+ int err = deflate(strm, flush);
|
|
|
|
|
if (err == Z_STREAM_ERROR)
|
|
|
|
|
return err;
|
|
|
|
|
- if (strm->avail_in || (s->strstart - s->block_start) + s->lookahead)
|
|
|
|
|
+ if (strm->avail_in || (s->strstart - s->block_start) + s->lookahead ||
|
|
|
|
|
+ !DEFLATE_DONE(strm, flush))
|
|
|
|
|
return Z_BUF_ERROR;
|
|
|
|
|
}
|
|
|
|
|
if (s->level != level) {
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -705,11 +727,13 @@ uLong ZEXPORT deflateBound(strm, sourceLen)
|
|
|
|
|
~13% overhead plus a small constant */
|
|
|
|
|
fixedlen = sourceLen + (sourceLen >> 3) + (sourceLen >> 8) +
|
|
|
|
|
(sourceLen >> 9) + 4;
|
|
|
|
|
+ DEFLATE_BOUND_ADJUST_COMPLEN(strm, fixedlen, sourceLen);
|
|
|
|
|
|
|
|
|
|
/* upper bound for stored blocks with length 127 (memLevel == 1) --
|
|
|
|
|
~4% overhead plus a small constant */
|
|
|
|
|
storelen = sourceLen + (sourceLen >> 5) + (sourceLen >> 7) +
|
|
|
|
|
(sourceLen >> 11) + 7;
|
|
|
|
|
+ DEFLATE_BOUND_ADJUST_COMPLEN(strm, storelen, sourceLen);
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
2022-10-17 14:31:23 +00:00
|
|
|
/* if can't get parameters, return larger bound plus a zlib wrapper */
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
if (deflateStateCheck(strm))
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -751,7 +775,8 @@ uLong ZEXPORT deflateBound(strm, sourceLen)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
}
|
|
|
|
|
|
2022-10-17 14:31:23 +00:00
|
|
|
/* if not default parameters, return one of the conservative bounds */
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
- if (s->w_bits != 15 || s->hash_bits != 8 + 7)
|
|
|
|
|
+ if (DEFLATE_NEED_CONSERVATIVE_BOUND(strm) ||
|
|
|
|
|
+ s->w_bits != 15 || s->hash_bits != 8 + 7)
|
2023-01-11 11:15:11 +00:00
|
|
|
return (s->w_bits <= s->hash_bits && s->level ? fixedlen : storelen) +
|
|
|
|
|
wraplen;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -780,7 +805,7 @@ local void putShortMSB(s, b)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
* applications may wish to modify it to avoid allocating a large
|
|
|
|
|
* strm->next_out buffer and copying into it. (See also read_buf()).
|
|
|
|
|
*/
|
|
|
|
|
-local void flush_pending(strm)
|
|
|
|
|
+void ZLIB_INTERNAL flush_pending(strm)
|
|
|
|
|
z_streamp strm;
|
|
|
|
|
{
|
|
|
|
|
unsigned len;
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -1052,7 +1077,8 @@ int ZEXPORT deflate(strm, flush)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
(flush != Z_NO_FLUSH && s->status != FINISH_STATE)) {
|
|
|
|
|
block_state bstate;
|
|
|
|
|
|
|
|
|
|
- bstate = s->level == 0 ? deflate_stored(s, flush) :
|
|
|
|
|
+ bstate = DEFLATE_HOOK(strm, flush, &bstate) ? bstate :
|
|
|
|
|
+ s->level == 0 ? deflate_stored(s, flush) :
|
|
|
|
|
s->strategy == Z_HUFFMAN_ONLY ? deflate_huff(s, flush) :
|
|
|
|
|
s->strategy == Z_RLE ? deflate_rle(s, flush) :
|
|
|
|
|
(*(configuration_table[s->level].func))(s, flush);
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -1099,7 +1125,6 @@ int ZEXPORT deflate(strm, flush)
|
2022-06-22 17:27:43 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
if (flush != Z_FINISH) return Z_OK;
|
|
|
|
|
- if (s->wrap <= 0) return Z_STREAM_END;
|
|
|
|
|
|
|
|
|
|
/* Write the trailer */
|
|
|
|
|
#ifdef GZIP
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -1115,7 +1140,7 @@ int ZEXPORT deflate(strm, flush)
|
2022-06-22 17:27:43 +00:00
|
|
|
}
|
|
|
|
|
else
|
|
|
|
|
#endif
|
|
|
|
|
- {
|
|
|
|
|
+ if (s->wrap == 1) {
|
|
|
|
|
putShortMSB(s, (uInt)(strm->adler >> 16));
|
|
|
|
|
putShortMSB(s, (uInt)(strm->adler & 0xffff));
|
|
|
|
|
}
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -1124,7 +1149,11 @@ int ZEXPORT deflate(strm, flush)
|
2022-06-22 17:27:43 +00:00
|
|
|
* to flush the rest.
|
|
|
|
|
*/
|
|
|
|
|
if (s->wrap > 0) s->wrap = -s->wrap; /* write the trailer only once! */
|
|
|
|
|
- return s->pending != 0 ? Z_OK : Z_STREAM_END;
|
|
|
|
|
+ if (s->pending == 0) {
|
|
|
|
|
+ Assert(s->bi_valid == 0, "bi_buf not flushed");
|
|
|
|
|
+ return Z_STREAM_END;
|
|
|
|
|
+ }
|
|
|
|
|
+ return Z_OK;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/* ========================================================================= */
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -1141,9 +1170,9 @@ int ZEXPORT deflateEnd(strm)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
TRY_FREE(strm, strm->state->pending_buf);
|
|
|
|
|
TRY_FREE(strm, strm->state->head);
|
|
|
|
|
TRY_FREE(strm, strm->state->prev);
|
|
|
|
|
- TRY_FREE(strm, strm->state->window);
|
|
|
|
|
+ TRY_FREE_WINDOW(strm, strm->state->window);
|
|
|
|
|
|
|
|
|
|
- ZFREE(strm, strm->state);
|
|
|
|
|
+ ZFREE_STATE(strm, strm->state);
|
|
|
|
|
strm->state = Z_NULL;
|
|
|
|
|
|
|
|
|
|
return status == BUSY_STATE ? Z_DATA_ERROR : Z_OK;
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -1173,13 +1202,13 @@ int ZEXPORT deflateCopy(dest, source)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
|
|
|
|
zmemcpy((voidpf)dest, (voidpf)source, sizeof(z_stream));
|
|
|
|
|
|
|
|
|
|
- ds = (deflate_state *) ZALLOC(dest, 1, sizeof(deflate_state));
|
|
|
|
|
+ ds = (deflate_state *) ZALLOC_STATE(dest, 1, sizeof(deflate_state));
|
|
|
|
|
if (ds == Z_NULL) return Z_MEM_ERROR;
|
|
|
|
|
dest->state = (struct internal_state FAR *) ds;
|
|
|
|
|
- zmemcpy((voidpf)ds, (voidpf)ss, sizeof(deflate_state));
|
|
|
|
|
+ ZCOPY_STATE((voidpf)ds, (voidpf)ss, sizeof(deflate_state));
|
|
|
|
|
ds->strm = dest;
|
|
|
|
|
|
|
|
|
|
- ds->window = (Bytef *) ZALLOC(dest, ds->w_size, 2*sizeof(Byte));
|
|
|
|
|
+ ds->window = (Bytef *) ZALLOC_WINDOW(dest, ds->w_size, 2*sizeof(Byte));
|
|
|
|
|
ds->prev = (Posf *) ZALLOC(dest, ds->w_size, sizeof(Pos));
|
|
|
|
|
ds->head = (Posf *) ZALLOC(dest, ds->hash_size, sizeof(Pos));
|
2022-06-22 17:27:43 +00:00
|
|
|
ds->pending_buf = (uchf *) ZALLOC(dest, ds->lit_bufsize, 4);
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -1226,7 +1255,8 @@ local unsigned read_buf(strm, buf, size)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
strm->avail_in -= len;
|
|
|
|
|
|
|
|
|
|
zmemcpy(buf, strm->next_in, len);
|
|
|
|
|
- if (strm->state->wrap == 1) {
|
2022-06-22 17:27:43 +00:00
|
|
|
+ if (!DEFLATE_NEED_CHECKSUM(strm)) {}
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+ else if (strm->state->wrap == 1) {
|
|
|
|
|
strm->adler = adler32(strm->adler, buf, len);
|
|
|
|
|
}
|
|
|
|
|
#ifdef GZIP
|
|
|
|
|
diff --git a/deflate.h b/deflate.h
|
2022-10-17 14:31:23 +00:00
|
|
|
index 1a06cd5..f92750c 100644
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
--- a/deflate.h
|
|
|
|
|
+++ b/deflate.h
|
2022-06-22 17:27:43 +00:00
|
|
|
@@ -299,6 +299,7 @@ void ZLIB_INTERNAL _tr_flush_bits OF((deflate_state *s));
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
void ZLIB_INTERNAL _tr_align OF((deflate_state *s));
|
|
|
|
|
void ZLIB_INTERNAL _tr_stored_block OF((deflate_state *s, charf *buf,
|
|
|
|
|
ulg stored_len, int last));
|
|
|
|
|
+void ZLIB_INTERNAL _tr_send_bits OF((deflate_state *s, int value, int length));
|
|
|
|
|
|
|
|
|
|
#define d_code(dist) \
|
|
|
|
|
((dist) < 256 ? _dist_code[dist] : _dist_code[256+((dist)>>7)])
|
2022-06-22 17:27:43 +00:00
|
|
|
@@ -343,4 +344,15 @@ void ZLIB_INTERNAL _tr_stored_block OF((deflate_state *s, charf *buf,
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
flush = _tr_tally(s, distance, length)
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
+typedef enum {
|
|
|
|
|
+ need_more, /* block not completed, need more input or more output */
|
|
|
|
|
+ block_done, /* block flush performed */
|
|
|
|
|
+ finish_started, /* finish started, need only more output at next deflate */
|
|
|
|
|
+ finish_done /* finish done, accept no more input or output */
|
|
|
|
|
+} block_state;
|
|
|
|
|
+
|
|
|
|
|
+unsigned ZLIB_INTERNAL bi_reverse OF((unsigned code, int len));
|
|
|
|
|
+void ZLIB_INTERNAL bi_windup OF((deflate_state *s));
|
|
|
|
|
+void ZLIB_INTERNAL flush_pending OF((z_streamp strm));
|
|
|
|
|
+
|
|
|
|
|
#endif /* DEFLATE_H */
|
|
|
|
|
diff --git a/gzguts.h b/gzguts.h
|
2022-10-17 14:31:23 +00:00
|
|
|
index 57faf37..581f2b6 100644
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
--- a/gzguts.h
|
|
|
|
|
+++ b/gzguts.h
|
|
|
|
|
@@ -153,7 +153,11 @@
|
|
|
|
|
|
|
|
|
|
/* default i/o buffer size -- double this for output when reading (this and
|
|
|
|
|
twice this must be able to fit in an unsigned type) */
|
|
|
|
|
+#ifdef DFLTCC
|
|
|
|
|
+#define GZBUFSIZE 131072
|
|
|
|
|
+#else
|
|
|
|
|
#define GZBUFSIZE 8192
|
|
|
|
|
+#endif
|
|
|
|
|
|
|
|
|
|
/* gzip modes, also provide a little integrity check on the passed structure */
|
|
|
|
|
#define GZ_NONE 0
|
|
|
|
|
diff --git a/inflate.c b/inflate.c
|
2023-01-11 11:15:11 +00:00
|
|
|
index 8acbef4..19dc724 100644
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
--- a/inflate.c
|
|
|
|
|
+++ b/inflate.c
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -85,6 +85,27 @@
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
#include "inflate.h"
|
|
|
|
|
#include "inffast.h"
|
|
|
|
|
|
|
|
|
|
+/* architecture-specific bits */
|
|
|
|
|
+#ifdef DFLTCC
|
|
|
|
|
+# include "contrib/s390/dfltcc.h"
|
|
|
|
|
+#else
|
|
|
|
|
+#define ZALLOC_STATE ZALLOC
|
|
|
|
|
+#define ZFREE_STATE ZFREE
|
|
|
|
|
+#define ZCOPY_STATE zmemcpy
|
|
|
|
|
+#define ZALLOC_WINDOW ZALLOC
|
2023-01-11 11:15:11 +00:00
|
|
|
+#define ZCOPY_WINDOW zmemcpy
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+#define ZFREE_WINDOW ZFREE
|
|
|
|
|
+#define INFLATE_RESET_KEEP_HOOK(strm) do {} while (0)
|
|
|
|
|
+#define INFLATE_PRIME_HOOK(strm, bits, value) do {} while (0)
|
|
|
|
|
+#define INFLATE_TYPEDO_HOOK(strm, flush) do {} while (0)
|
|
|
|
|
+#define INFLATE_NEED_CHECKSUM(strm) 1
|
|
|
|
|
+#define INFLATE_NEED_UPDATEWINDOW(strm) 1
|
|
|
|
|
+#define INFLATE_MARK_HOOK(strm) do {} while (0)
|
2022-06-22 17:27:43 +00:00
|
|
|
+#define INFLATE_SYNC_POINT_HOOK(strm) do {} while (0)
|
2023-01-11 11:15:11 +00:00
|
|
|
+#define INFLATE_SET_DICTIONARY_HOOK(strm, dict, dict_len) do {} while (0)
|
|
|
|
|
+#define INFLATE_GET_DICTIONARY_HOOK(strm, dict, dict_len) do {} while (0)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
+#endif
|
|
|
|
|
+
|
|
|
|
|
#ifdef MAKEFIXED
|
|
|
|
|
# ifndef BUILDFIXED
|
|
|
|
|
# define BUILDFIXED
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -138,6 +159,7 @@ z_streamp strm;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
state->lencode = state->distcode = state->next = state->codes;
|
|
|
|
|
state->sane = 1;
|
|
|
|
|
state->back = -1;
|
|
|
|
|
+ INFLATE_RESET_KEEP_HOOK(strm);
|
|
|
|
|
Tracev((stderr, "inflate: reset\n"));
|
|
|
|
|
return Z_OK;
|
|
|
|
|
}
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -185,7 +207,7 @@ int windowBits;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
if (windowBits && (windowBits < 8 || windowBits > 15))
|
|
|
|
|
return Z_STREAM_ERROR;
|
|
|
|
|
if (state->window != Z_NULL && state->wbits != (unsigned)windowBits) {
|
|
|
|
|
- ZFREE(strm, state->window);
|
|
|
|
|
+ ZFREE_WINDOW(strm, state->window);
|
|
|
|
|
state->window = Z_NULL;
|
|
|
|
|
}
|
|
|
|
|
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -224,7 +246,7 @@ int stream_size;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
strm->zfree = zcfree;
|
|
|
|
|
#endif
|
|
|
|
|
state = (struct inflate_state FAR *)
|
|
|
|
|
- ZALLOC(strm, 1, sizeof(struct inflate_state));
|
|
|
|
|
+ ZALLOC_STATE(strm, 1, sizeof(struct inflate_state));
|
|
|
|
|
if (state == Z_NULL) return Z_MEM_ERROR;
|
|
|
|
|
Tracev((stderr, "inflate: allocated\n"));
|
|
|
|
|
strm->state = (struct internal_state FAR *)state;
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -233,7 +255,7 @@ int stream_size;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
state->mode = HEAD; /* to pass state test in inflateReset2() */
|
|
|
|
|
ret = inflateReset2(strm, windowBits);
|
|
|
|
|
if (ret != Z_OK) {
|
|
|
|
|
- ZFREE(strm, state);
|
|
|
|
|
+ ZFREE_STATE(strm, state);
|
|
|
|
|
strm->state = Z_NULL;
|
|
|
|
|
}
|
|
|
|
|
return ret;
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -255,6 +277,7 @@ int value;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
struct inflate_state FAR *state;
|
|
|
|
|
|
|
|
|
|
if (inflateStateCheck(strm)) return Z_STREAM_ERROR;
|
|
|
|
|
+ INFLATE_PRIME_HOOK(strm, bits, value);
|
|
|
|
|
state = (struct inflate_state FAR *)strm->state;
|
|
|
|
|
if (bits < 0) {
|
|
|
|
|
state->hold = 0;
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -382,6 +405,27 @@ void makefixed()
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
}
|
|
|
|
|
#endif /* MAKEFIXED */
|
|
|
|
|
|
|
|
|
|
+int ZLIB_INTERNAL inflate_ensure_window(state)
|
|
|
|
|
+ struct inflate_state *state;
|
|
|
|
|
+{
|
|
|
|
|
+ /* if it hasn't been done already, allocate space for the window */
|
|
|
|
|
+ if (state->window == Z_NULL) {
|
|
|
|
|
+ state->window = (unsigned char FAR *)
|
|
|
|
|
+ ZALLOC_WINDOW(state->strm, 1U << state->wbits,
|
|
|
|
|
+ sizeof(unsigned char));
|
|
|
|
|
+ if (state->window == Z_NULL) return 1;
|
|
|
|
|
+ }
|
|
|
|
|
+
|
|
|
|
|
+ /* if window not in use yet, initialize */
|
|
|
|
|
+ if (state->wsize == 0) {
|
|
|
|
|
+ state->wsize = 1U << state->wbits;
|
|
|
|
|
+ state->wnext = 0;
|
|
|
|
|
+ state->whave = 0;
|
|
|
|
|
+ }
|
|
|
|
|
+
|
|
|
|
|
+ return 0;
|
|
|
|
|
+}
|
|
|
|
|
+
|
|
|
|
|
/*
|
|
|
|
|
Update the window with the last wsize (normally 32K) bytes written before
|
|
|
|
|
returning. If window does not exist yet, create it. This is only called
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -406,20 +450,7 @@ unsigned copy;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
|
|
|
|
state = (struct inflate_state FAR *)strm->state;
|
|
|
|
|
|
|
|
|
|
- /* if it hasn't been done already, allocate space for the window */
|
|
|
|
|
- if (state->window == Z_NULL) {
|
|
|
|
|
- state->window = (unsigned char FAR *)
|
|
|
|
|
- ZALLOC(strm, 1U << state->wbits,
|
|
|
|
|
- sizeof(unsigned char));
|
|
|
|
|
- if (state->window == Z_NULL) return 1;
|
|
|
|
|
- }
|
|
|
|
|
-
|
|
|
|
|
- /* if window not in use yet, initialize */
|
|
|
|
|
- if (state->wsize == 0) {
|
|
|
|
|
- state->wsize = 1U << state->wbits;
|
|
|
|
|
- state->wnext = 0;
|
|
|
|
|
- state->whave = 0;
|
|
|
|
|
- }
|
|
|
|
|
+ if (inflate_ensure_window(state)) return 1;
|
|
|
|
|
|
|
|
|
|
/* copy state->wsize or less output bytes into the circular window */
|
|
|
|
|
if (copy >= state->wsize) {
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -863,6 +894,7 @@ int flush;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
if (flush == Z_BLOCK || flush == Z_TREES) goto inf_leave;
|
2022-06-22 17:27:43 +00:00
|
|
|
/* fallthrough */
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
case TYPEDO:
|
|
|
|
|
+ INFLATE_TYPEDO_HOOK(strm, flush);
|
|
|
|
|
if (state->last) {
|
|
|
|
|
BYTEBITS();
|
|
|
|
|
state->mode = CHECK;
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -1224,7 +1256,7 @@ int flush;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
out -= left;
|
|
|
|
|
strm->total_out += out;
|
|
|
|
|
state->total += out;
|
|
|
|
|
- if ((state->wrap & 4) && out)
|
|
|
|
|
+ if (INFLATE_NEED_CHECKSUM(strm) && (state->wrap & 4) && out)
|
|
|
|
|
strm->adler = state->check =
|
2022-06-22 17:27:43 +00:00
|
|
|
UPDATE_CHECK(state->check, put - out, out);
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
out = left;
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -1279,8 +1311,9 @@ int flush;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
*/
|
|
|
|
|
inf_leave:
|
|
|
|
|
RESTORE();
|
|
|
|
|
- if (state->wsize || (out != strm->avail_out && state->mode < BAD &&
|
|
|
|
|
- (state->mode < CHECK || flush != Z_FINISH)))
|
|
|
|
|
+ if (INFLATE_NEED_UPDATEWINDOW(strm) &&
|
2022-06-22 17:27:43 +00:00
|
|
|
+ (state->wsize || (out != strm->avail_out && state->mode < BAD &&
|
|
|
|
|
+ (state->mode < CHECK || flush != Z_FINISH))))
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
if (updatewindow(strm, strm->next_out, out - strm->avail_out)) {
|
|
|
|
|
state->mode = MEM;
|
|
|
|
|
return Z_MEM_ERROR;
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -1290,7 +1323,7 @@ int flush;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
strm->total_in += in;
|
|
|
|
|
strm->total_out += out;
|
|
|
|
|
state->total += out;
|
|
|
|
|
- if ((state->wrap & 4) && out)
|
|
|
|
|
+ if (INFLATE_NEED_CHECKSUM(strm) && (state->wrap & 4) && out)
|
|
|
|
|
strm->adler = state->check =
|
2022-06-22 17:27:43 +00:00
|
|
|
UPDATE_CHECK(state->check, strm->next_out - out, out);
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
strm->data_type = (int)state->bits + (state->last ? 64 : 0) +
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -1308,8 +1341,8 @@ z_streamp strm;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
if (inflateStateCheck(strm))
|
|
|
|
|
return Z_STREAM_ERROR;
|
|
|
|
|
state = (struct inflate_state FAR *)strm->state;
|
|
|
|
|
- if (state->window != Z_NULL) ZFREE(strm, state->window);
|
|
|
|
|
- ZFREE(strm, strm->state);
|
|
|
|
|
+ if (state->window != Z_NULL) ZFREE_WINDOW(strm, state->window);
|
|
|
|
|
+ ZFREE_STATE(strm, strm->state);
|
|
|
|
|
strm->state = Z_NULL;
|
|
|
|
|
Tracev((stderr, "inflate: end\n"));
|
|
|
|
|
return Z_OK;
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -1326,6 +1359,8 @@ uInt *dictLength;
|
|
|
|
|
if (inflateStateCheck(strm)) return Z_STREAM_ERROR;
|
|
|
|
|
state = (struct inflate_state FAR *)strm->state;
|
|
|
|
|
|
|
|
|
|
+ INFLATE_GET_DICTIONARY_HOOK(strm, dictionary, dictLength);
|
|
|
|
|
+
|
|
|
|
|
/* copy dictionary */
|
|
|
|
|
if (state->whave && dictionary != Z_NULL) {
|
|
|
|
|
zmemcpy(dictionary, state->window + state->wnext,
|
|
|
|
|
@@ -1361,6 +1396,8 @@ uInt dictLength;
|
|
|
|
|
return Z_DATA_ERROR;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
+ INFLATE_SET_DICTIONARY_HOOK(strm, dictionary, dictLength);
|
|
|
|
|
+
|
|
|
|
|
/* copy dictionary to window using updatewindow(), which will amend the
|
|
|
|
|
existing dictionary if appropriate */
|
|
|
|
|
ret = updatewindow(strm, dictionary + dictLength, dictLength);
|
|
|
|
|
@@ -1488,6 +1525,7 @@ z_streamp strm;
|
2022-06-22 17:27:43 +00:00
|
|
|
struct inflate_state FAR *state;
|
|
|
|
|
|
|
|
|
|
if (inflateStateCheck(strm)) return Z_STREAM_ERROR;
|
|
|
|
|
+ INFLATE_SYNC_POINT_HOOK(strm);
|
|
|
|
|
state = (struct inflate_state FAR *)strm->state;
|
|
|
|
|
return state->mode == STORED && state->bits == 0;
|
|
|
|
|
}
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -1508,21 +1546,22 @@ z_streamp source;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
|
|
|
|
/* allocate space */
|
|
|
|
|
copy = (struct inflate_state FAR *)
|
|
|
|
|
- ZALLOC(source, 1, sizeof(struct inflate_state));
|
|
|
|
|
+ ZALLOC_STATE(source, 1, sizeof(struct inflate_state));
|
|
|
|
|
if (copy == Z_NULL) return Z_MEM_ERROR;
|
|
|
|
|
window = Z_NULL;
|
|
|
|
|
if (state->window != Z_NULL) {
|
|
|
|
|
window = (unsigned char FAR *)
|
|
|
|
|
- ZALLOC(source, 1U << state->wbits, sizeof(unsigned char));
|
2022-06-22 17:27:43 +00:00
|
|
|
+ ZALLOC_WINDOW(source, 1U << state->wbits,
|
|
|
|
|
+ sizeof(unsigned char));
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
if (window == Z_NULL) {
|
|
|
|
|
- ZFREE(source, copy);
|
|
|
|
|
+ ZFREE_STATE(source, copy);
|
|
|
|
|
return Z_MEM_ERROR;
|
|
|
|
|
}
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/* copy state */
|
|
|
|
|
zmemcpy((voidpf)dest, (voidpf)source, sizeof(z_stream));
|
|
|
|
|
- zmemcpy((voidpf)copy, (voidpf)state, sizeof(struct inflate_state));
|
|
|
|
|
+ ZCOPY_STATE((voidpf)copy, (voidpf)state, sizeof(struct inflate_state));
|
|
|
|
|
copy->strm = dest;
|
|
|
|
|
if (state->lencode >= state->codes &&
|
|
|
|
|
state->lencode <= state->codes + ENOUGH - 1) {
|
2023-01-11 11:15:11 +00:00
|
|
|
@@ -1531,8 +1570,7 @@ z_streamp source;
|
|
|
|
|
}
|
|
|
|
|
copy->next = copy->codes + (state->next - state->codes);
|
|
|
|
|
if (window != Z_NULL) {
|
|
|
|
|
- wsize = 1U << state->wbits;
|
|
|
|
|
- zmemcpy(window, state->window, wsize);
|
|
|
|
|
+ ZCOPY_WINDOW(window, state->window, 1U << state->wbits);
|
|
|
|
|
}
|
|
|
|
|
copy->window = window;
|
|
|
|
|
dest->state = (struct internal_state FAR *)copy;
|
|
|
|
|
@@ -1579,6 +1617,7 @@ z_streamp strm;
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
|
|
|
|
|
if (inflateStateCheck(strm))
|
|
|
|
|
return -(1L << 16);
|
|
|
|
|
+ INFLATE_MARK_HOOK(strm);
|
|
|
|
|
state = (struct inflate_state FAR *)strm->state;
|
|
|
|
|
return (long)(((unsigned long)((long)state->back)) << 16) +
|
|
|
|
|
(state->mode == COPY ? state->length :
|
|
|
|
|
diff --git a/inflate.h b/inflate.h
|
2022-10-17 14:31:23 +00:00
|
|
|
index f127b6b..519ed35 100644
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
--- a/inflate.h
|
|
|
|
|
+++ b/inflate.h
|
2022-06-22 17:27:43 +00:00
|
|
|
@@ -124,3 +124,5 @@ struct inflate_state {
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
int back; /* bits back of last unprocessed length/lit */
|
|
|
|
|
unsigned was; /* initial length of match */
|
|
|
|
|
};
|
|
|
|
|
+
|
|
|
|
|
+int ZLIB_INTERNAL inflate_ensure_window OF((struct inflate_state *state));
|
|
|
|
|
diff --git a/test/infcover.c b/test/infcover.c
|
2022-10-17 14:31:23 +00:00
|
|
|
index 2be0164..a208219 100644
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
--- a/test/infcover.c
|
|
|
|
|
+++ b/test/infcover.c
|
2022-06-22 17:27:43 +00:00
|
|
|
@@ -373,7 +373,7 @@ local void cover_support(void)
|
|
|
|
|
mem_setup(&strm);
|
|
|
|
|
strm.avail_in = 0;
|
|
|
|
|
strm.next_in = Z_NULL;
|
|
|
|
|
- ret = inflateInit_(&strm, ZLIB_VERSION - 1, (int)sizeof(z_stream));
|
|
|
|
|
+ ret = inflateInit_(&strm, &ZLIB_VERSION[1], (int)sizeof(z_stream));
|
|
|
|
|
assert(ret == Z_VERSION_ERROR);
|
|
|
|
|
mem_done(&strm, "wrong version");
|
|
|
|
|
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
@@ -444,7 +444,7 @@ local void cover_wrap(void)
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/* input and output functions for inflateBack() */
|
|
|
|
|
-local unsigned pull(void *desc, unsigned char **buf)
|
|
|
|
|
+local unsigned pull(void *desc, z_const unsigned char **buf)
|
|
|
|
|
{
|
|
|
|
|
static unsigned int next = 0;
|
|
|
|
|
static unsigned char dat[] = {0x63, 0, 2, 0};
|
|
|
|
|
diff --git a/test/minigzip.c b/test/minigzip.c
|
2022-10-17 14:31:23 +00:00
|
|
|
index a649d2b..964408a 100644
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
--- a/test/minigzip.c
|
|
|
|
|
+++ b/test/minigzip.c
|
|
|
|
|
@@ -132,7 +132,11 @@ static void pwinerror (s)
|
|
|
|
|
#endif
|
|
|
|
|
#define SUFFIX_LEN (sizeof(GZ_SUFFIX)-1)
|
|
|
|
|
|
|
|
|
|
+#ifdef DFLTCC
|
|
|
|
|
+#define BUFLEN 262144
|
|
|
|
|
+#else
|
|
|
|
|
#define BUFLEN 16384
|
|
|
|
|
+#endif
|
|
|
|
|
#define MAX_NAME_LEN 1024
|
|
|
|
|
|
|
|
|
|
#ifdef MAXSEG_64K
|
|
|
|
|
diff --git a/trees.c b/trees.c
|
2022-10-17 14:31:23 +00:00
|
|
|
index 5f305c4..4924bdf 100644
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
--- a/trees.c
|
|
|
|
|
+++ b/trees.c
|
|
|
|
|
@@ -149,8 +149,6 @@ local void send_all_trees OF((deflate_state *s, int lcodes, int dcodes,
|
|
|
|
|
local void compress_block OF((deflate_state *s, const ct_data *ltree,
|
|
|
|
|
const ct_data *dtree));
|
|
|
|
|
local int detect_data_type OF((deflate_state *s));
|
2022-06-22 17:27:43 +00:00
|
|
|
-local unsigned bi_reverse OF((unsigned code, int len));
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
-local void bi_windup OF((deflate_state *s));
|
|
|
|
|
local void bi_flush OF((deflate_state *s));
|
|
|
|
|
|
|
|
|
|
#ifdef GEN_TREES_H
|
|
|
|
|
@@ -223,6 +221,13 @@ local void send_bits(s, value, length)
|
|
|
|
|
}
|
|
|
|
|
#endif /* ZLIB_DEBUG */
|
|
|
|
|
|
|
|
|
|
+void ZLIB_INTERNAL _tr_send_bits(s, value, length)
|
|
|
|
|
+ deflate_state *s;
|
|
|
|
|
+ int value;
|
|
|
|
|
+ int length;
|
|
|
|
|
+{
|
|
|
|
|
+ send_bits(s, value, length);
|
|
|
|
|
+}
|
|
|
|
|
|
|
|
|
|
/* the arguments must not have side effects */
|
|
|
|
|
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -1133,7 +1138,7 @@ local int detect_data_type(s)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
* method would use a table)
|
|
|
|
|
* IN assertion: 1 <= len <= 15
|
|
|
|
|
*/
|
|
|
|
|
-local unsigned bi_reverse(code, len)
|
|
|
|
|
+unsigned ZLIB_INTERNAL bi_reverse(code, len)
|
|
|
|
|
unsigned code; /* the value to invert */
|
|
|
|
|
int len; /* its bit length */
|
|
|
|
|
{
|
2022-10-17 14:31:23 +00:00
|
|
|
@@ -1165,7 +1170,7 @@ local void bi_flush(s)
|
Add support for IBM Z hardware-accelerated deflate
Future versions of IBM Z mainframes will provide DFLTCC instruction,
which implements deflate algorithm in hardware with estimated
compression and decompression performance orders of magnitude faster
than the current zlib and ratio comparable with that of level 1.
This patch adds DFLTCC support to zlib. In order to enable it, the
following build commands should be used:
$ CFLAGS=-DDFLTCC ./configure
$ make OBJA=dfltcc.o PIC_OBJA=dfltcc.lo
When built like this, zlib would compress in hardware on level 1, and in
software on all other levels. Decompression will always happen in
hardware. In order to enable DFLTCC compression for levels 1-6 (i.e. to
make it used by default) one could either add -DDFLTCC_LEVEL_MASK=0x7e
at compile time, or set the environment variable DFLTCC_LEVEL_MASK to
0x7e at run time.
Two DFLTCC compression calls produce the same results only when they
both are made on machines of the same generation, and when the
respective buffers have the same offset relative to the start of the
page. Therefore care should be taken when using hardware compression
when reproducible results are desired. One such use case - reproducible
software builds - is handled explicitly: when SOURCE_DATE_EPOCH
environment variable is set, the hardware compression is disabled.
DFLTCC does not support every single zlib feature, in particular:
* inflate(Z_BLOCK) and inflate(Z_TREES)
* inflateMark()
* inflatePrime()
* deflateParams() after the first deflate() call
When used, these functions will either switch to software, or, in case
this is not possible, gracefully fail.
This patch tries to add DFLTCC support in a least intrusive way.
All SystemZ-specific code was placed into a separate file, but
unfortunately there is still a noticeable amount of changes in the
main zlib code. Below is the summary of those changes.
DFLTCC takes as arguments a parameter block, an input buffer, an output
buffer and a window. Since DFLTCC requires parameter block to be
doubleword-aligned, and it's reasonable to allocate it alongside
deflate and inflate states, ZALLOC_STATE, ZFREE_STATE and ZCOPY_STATE
macros were introduced in order to encapsulate the allocation details.
The same is true for window, for which ZALLOC_WINDOW and
TRY_FREE_WINDOW macros were introduced.
While for inflate software and hardware window formats match, this is
not the case for deflate. Therefore, deflateSetDictionary and
deflateGetDictionary need special handling, which is triggered using the
new DEFLATE_SET_DICTIONARY_HOOK and DEFLATE_GET_DICTIONARY_HOOK macros.
deflateResetKeep() and inflateResetKeep() now update the DFLTCC
parameter block, which is allocated alongside zlib state, using
the new DEFLATE_RESET_KEEP_HOOK and INFLATE_RESET_KEEP_HOOK macros.
In order to make unsupported deflateParams(), inflatePrime() and
inflateMark() calls to fail gracefully, the new DEFLATE_PARAMS_HOOK,
INFLATE_PRIME_HOOK and INFLATE_MARK_HOOK macros were introduced.
The algorithm implemented in hardware has different compression ratio
than the one implemented in software. In order for deflateBound() to
return the correct results for the hardware implementation, the new
DEFLATE_BOUND_ADJUST_COMPLEN and DEFLATE_NEED_CONSERVATIVE_BOUND macros
were introduced.
Actual compression and decompression are handled by the new DEFLATE_HOOK
and INFLATE_TYPEDO_HOOK macros. Since inflation with DFLTCC manages the
window on its own, calling updatewindow() is suppressed using the new
INFLATE_NEED_UPDATEWINDOW() macro.
In addition to compression, DFLTCC computes CRC-32 and Adler-32
checksums, therefore, whenever it's used, software checksumming needs to
be suppressed using the new DEFLATE_NEED_CHECKSUM and
INFLATE_NEED_CHECKSUM macros.
DFLTCC will refuse to write an End-of-block Symbol if there is no input
data, thus in some cases it is necessary to do this manually. In order
to achieve this, send_bits, bi_reverse, bi_windup and flush_pending
were promoted from local to ZLIB_INTERNAL. Furthermore, since block and
stream termination must be handled in software as well, block_state enum
was moved to deflate.h.
Since the first call to dfltcc_inflate already needs the window, and it
might be not allocated yet, inflate_ensure_window was factored out of
updatewindow and made ZLIB_INTERNAL.
2019-08-01 07:14:52 +00:00
|
|
|
/* ===========================================================================
|
|
|
|
|
* Flush the bit buffer and align the output on a byte boundary
|
|
|
|
|
*/
|
|
|
|
|
-local void bi_windup(s)
|
|
|
|
|
+void ZLIB_INTERNAL bi_windup(s)
|
|
|
|
|
deflate_state *s;
|
|
|
|
|
{
|
|
|
|
|
if (s->bi_valid > 8) {
|
2022-06-22 17:27:43 +00:00
|
|
|
diff --git a/zutil.h b/zutil.h
|
2022-10-17 14:31:23 +00:00
|
|
|
index 0bc7f4e..75eb4df 100644
|
2022-06-22 17:27:43 +00:00
|
|
|
--- a/zutil.h
|
|
|
|
|
+++ b/zutil.h
|
|
|
|
|
@@ -87,6 +87,8 @@ extern z_const char * const z_errmsg[10]; /* indexed by 2-zlib_error */
|
|
|
|
|
|
|
|
|
|
#define PRESET_DICT 0x20 /* preset dictionary flag in zlib header */
|
|
|
|
|
|
|
|
|
|
+#define ZLIB_WRAPLEN 6 /* zlib format overhead */
|
|
|
|
|
+
|
|
|
|
|
/* target dependencies */
|
|
|
|
|
|
|
|
|
|
#if defined(MSDOS) || (defined(WINDOWS) && !defined(WIN32))
|
2022-10-17 14:31:23 +00:00
|
|
|
--
|
2023-01-11 11:15:11 +00:00
|
|
|
2.38.1
|
2022-10-17 14:31:23 +00:00
|
|
|
|
