e3f2f926dd
With FADump support added on POWERNV paltform, enable the scripts to capture /proc/vmcore. Also, if CONFIG_OPAL_CORE is enabled, OPAL core is preserved and exported on POWERNV platform. So, offload OPAL core, if it is available. Signed-off-by: Hari Bathini <hbathini@linux.ibm.com> Acked-by: Kairui Song <kasong@redhat.com>
278 lines
7.8 KiB
Bash
Executable File
278 lines
7.8 KiB
Bash
Executable File
# These variables and functions are useful in 2nd kernel
|
|
|
|
. /lib/kdump-lib.sh
|
|
|
|
KDUMP_PATH="/var/crash"
|
|
CORE_COLLECTOR=""
|
|
DEFAULT_CORE_COLLECTOR="makedumpfile -l --message-level 1 -d 31"
|
|
DMESG_COLLECTOR="/sbin/vmcore-dmesg"
|
|
FAILURE_ACTION="systemctl reboot -f"
|
|
DATEDIR=`date +%Y-%m-%d-%T`
|
|
HOST_IP='127.0.0.1'
|
|
DUMP_INSTRUCTION=""
|
|
SSH_KEY_LOCATION="/root/.ssh/kdump_id_rsa"
|
|
KDUMP_SCRIPT_DIR="/kdumpscripts"
|
|
DD_BLKSIZE=512
|
|
FINAL_ACTION="systemctl reboot -f"
|
|
KDUMP_CONF="/etc/kdump.conf"
|
|
KDUMP_PRE=""
|
|
KDUMP_POST=""
|
|
NEWROOT="/sysroot"
|
|
OPALCORE="/sys/firmware/opal/mpipl/core"
|
|
|
|
get_kdump_confs()
|
|
{
|
|
local config_opt config_val
|
|
|
|
while read config_opt config_val;
|
|
do
|
|
# remove inline comments after the end of a directive.
|
|
case "$config_opt" in
|
|
path)
|
|
KDUMP_PATH="$config_val"
|
|
;;
|
|
core_collector)
|
|
[ -n "$config_val" ] && CORE_COLLECTOR="$config_val"
|
|
;;
|
|
sshkey)
|
|
if [ -f "$config_val" ]; then
|
|
SSH_KEY_LOCATION=$config_val
|
|
fi
|
|
;;
|
|
kdump_pre)
|
|
KDUMP_PRE="$config_val"
|
|
;;
|
|
kdump_post)
|
|
KDUMP_POST="$config_val"
|
|
;;
|
|
fence_kdump_args)
|
|
FENCE_KDUMP_ARGS="$config_val"
|
|
;;
|
|
fence_kdump_nodes)
|
|
FENCE_KDUMP_NODES="$config_val"
|
|
;;
|
|
failure_action|default)
|
|
case $config_val in
|
|
shell)
|
|
FAILURE_ACTION="kdump_emergency_shell"
|
|
;;
|
|
reboot)
|
|
FAILURE_ACTION="systemctl reboot -f && exit"
|
|
;;
|
|
halt)
|
|
FAILURE_ACTION="halt && exit"
|
|
;;
|
|
poweroff)
|
|
FAILURE_ACTION="systemctl poweroff -f && exit"
|
|
;;
|
|
dump_to_rootfs)
|
|
FAILURE_ACTION="dump_to_rootfs"
|
|
;;
|
|
esac
|
|
;;
|
|
final_action)
|
|
case $config_val in
|
|
reboot)
|
|
FINAL_ACTION="systemctl reboot -f"
|
|
;;
|
|
halt)
|
|
FINAL_ACTION="halt"
|
|
;;
|
|
poweroff)
|
|
FINAL_ACTION="systemctl poweroff -f"
|
|
;;
|
|
esac
|
|
;;
|
|
esac
|
|
done <<< "$(read_strip_comments $KDUMP_CONF)"
|
|
|
|
if [ -z "$CORE_COLLECTOR" ]; then
|
|
CORE_COLLECTOR="$DEFAULT_CORE_COLLECTOR"
|
|
if is_ssh_dump_target || is_raw_dump_target; then
|
|
CORE_COLLECTOR="$CORE_COLLECTOR -F"
|
|
fi
|
|
fi
|
|
}
|
|
|
|
# dump_fs <mount point| device>
|
|
dump_fs()
|
|
{
|
|
local _do_umount=""
|
|
local _dev=$(findmnt -k -f -n -r -o SOURCE $1)
|
|
local _mp=$(findmnt -k -f -n -r -o TARGET $1)
|
|
local _op=$(findmnt -k -f -n -r -o OPTIONS $1)
|
|
|
|
if [ -z "$_mp" ]; then
|
|
_dev=$(findmnt -s -f -n -r -o SOURCE $1)
|
|
_mp=$(findmnt -s -f -n -r -o TARGET $1)
|
|
_op=$(findmnt -s -f -n -r -o OPTIONS $1)
|
|
|
|
if [ -n "$_dev" ] && [ -n "$_mp" ]; then
|
|
echo "kdump: dump target $_dev is not mounted, trying to mount..."
|
|
mkdir -p $_mp
|
|
mount -o $_op $_dev $_mp
|
|
|
|
if [ $? -ne 0 ]; then
|
|
echo "kdump: mounting failed (mount point: $_mp, option: $_op)"
|
|
return 1
|
|
fi
|
|
_do_umount=1
|
|
else
|
|
echo "kdump: error: Dump target $_dev is not usable"
|
|
fi
|
|
else
|
|
echo "kdump: dump target is $_dev"
|
|
fi
|
|
|
|
# Remove -F in makedumpfile case. We don't want a flat format dump here.
|
|
[[ $CORE_COLLECTOR = *makedumpfile* ]] && CORE_COLLECTOR=`echo $CORE_COLLECTOR | sed -e "s/-F//g"`
|
|
|
|
echo "kdump: saving to $_mp/$KDUMP_PATH/$HOST_IP-$DATEDIR/"
|
|
|
|
# Only remount to read-write mode if the dump target is mounted read-only.
|
|
if [[ "$_op" = "ro"* ]]; then
|
|
echo "kdump: Mounting Dump target $_dev in rw mode."
|
|
mount -o remount,rw $_dev $_mp || return 1
|
|
fi
|
|
|
|
mkdir -p $_mp/$KDUMP_PATH/$HOST_IP-$DATEDIR || return 1
|
|
|
|
save_vmcore_dmesg_fs ${DMESG_COLLECTOR} "$_mp/$KDUMP_PATH/$HOST_IP-$DATEDIR/"
|
|
save_opalcore_fs "$_mp/$KDUMP_PATH/$HOST_IP-$DATEDIR/"
|
|
|
|
echo "kdump: saving vmcore"
|
|
$CORE_COLLECTOR /proc/vmcore $_mp/$KDUMP_PATH/$HOST_IP-$DATEDIR/vmcore-incomplete || return 1
|
|
mv $_mp/$KDUMP_PATH/$HOST_IP-$DATEDIR/vmcore-incomplete $_mp/$KDUMP_PATH/$HOST_IP-$DATEDIR/vmcore
|
|
sync
|
|
|
|
echo "kdump: saving vmcore complete"
|
|
|
|
if [ $_do_umount ]; then
|
|
umount $_mp || echo "kdump: warn: failed to umount target"
|
|
fi
|
|
|
|
# improper kernel cmdline can cause the failure of echo, we can ignore this kind of failure
|
|
return 0
|
|
}
|
|
|
|
save_vmcore_dmesg_fs() {
|
|
local _dmesg_collector=$1
|
|
local _path=$2
|
|
|
|
echo "kdump: saving vmcore-dmesg.txt"
|
|
$_dmesg_collector /proc/vmcore > ${_path}/vmcore-dmesg-incomplete.txt
|
|
_exitcode=$?
|
|
if [ $_exitcode -eq 0 ]; then
|
|
mv ${_path}/vmcore-dmesg-incomplete.txt ${_path}/vmcore-dmesg.txt
|
|
|
|
# Make sure file is on disk. There have been instances where later
|
|
# saving vmcore failed and system rebooted without sync and there
|
|
# was no vmcore-dmesg.txt available.
|
|
sync
|
|
echo "kdump: saving vmcore-dmesg.txt complete"
|
|
else
|
|
echo "kdump: saving vmcore-dmesg.txt failed"
|
|
fi
|
|
}
|
|
|
|
save_opalcore_fs() {
|
|
local _path=$1
|
|
|
|
if [ ! -f $OPALCORE ]; then
|
|
# Check if we are on an old kernel that uses a different path
|
|
if [ -f /sys/firmware/opal/core ]; then
|
|
OPALCORE="/sys/firmware/opal/core"
|
|
else
|
|
return 0
|
|
fi
|
|
fi
|
|
|
|
echo "kdump: saving opalcore"
|
|
cp $OPALCORE ${_path}/opalcore
|
|
if [ $? -ne 0 ]; then
|
|
echo "kdump: saving opalcore failed"
|
|
return 1
|
|
fi
|
|
|
|
sync
|
|
echo "kdump: saving opalcore complete"
|
|
return 0
|
|
}
|
|
|
|
dump_to_rootfs()
|
|
{
|
|
|
|
echo "Kdump: trying to bring up rootfs device"
|
|
systemctl start dracut-initqueue
|
|
echo "Kdump: waiting for rootfs mount, will timeout after 90 seconds"
|
|
systemctl start sysroot.mount
|
|
|
|
dump_fs $NEWROOT
|
|
}
|
|
|
|
kdump_emergency_shell()
|
|
{
|
|
echo "PS1=\"kdump:\\\${PWD}# \"" >/etc/profile
|
|
/bin/dracut-emergency
|
|
rm -f /etc/profile
|
|
}
|
|
|
|
do_failure_action()
|
|
{
|
|
echo "Kdump: Executing failure action $FAILURE_ACTION"
|
|
eval $FAILURE_ACTION
|
|
}
|
|
|
|
do_final_action()
|
|
{
|
|
eval $FINAL_ACTION
|
|
}
|
|
|
|
get_host_ip()
|
|
{
|
|
local _host
|
|
if is_nfs_dump_target || is_ssh_dump_target
|
|
then
|
|
kdumpnic=$(getarg kdumpnic=)
|
|
[ -z "$kdumpnic" ] && echo "kdump: failed to get kdumpnic!" && return 1
|
|
_host=`ip addr show dev $kdumpnic|grep '[ ]*inet'`
|
|
[ $? -ne 0 ] && echo "kdump: wrong kdumpnic: $kdumpnic" && return 1
|
|
_host=`echo $_host | head -n 1 | cut -d' ' -f2`
|
|
_host="${_host%%/*}"
|
|
[ -z "$_host" ] && echo "kdump: wrong kdumpnic: $kdumpnic" && return 1
|
|
HOST_IP=$_host
|
|
fi
|
|
return 0
|
|
}
|
|
|
|
read_kdump_conf()
|
|
{
|
|
if [ ! -f "$KDUMP_CONF" ]; then
|
|
echo "kdump: $KDUMP_CONF not found"
|
|
return
|
|
fi
|
|
|
|
get_kdump_confs
|
|
|
|
# rescan for add code for dump target
|
|
while read config_opt config_val;
|
|
do
|
|
# remove inline comments after the end of a directive.
|
|
case "$config_opt" in
|
|
dracut_args)
|
|
config_val=$(get_dracut_args_target "$config_val")
|
|
[ -n "$config_val" ] && add_dump_code "dump_fs $config_val"
|
|
;;
|
|
ext[234]|xfs|btrfs|minix|nfs)
|
|
add_dump_code "dump_fs $config_val"
|
|
;;
|
|
raw)
|
|
add_dump_code "dump_raw $config_val"
|
|
;;
|
|
ssh)
|
|
add_dump_code "dump_ssh $SSH_KEY_LOCATION $config_val"
|
|
;;
|
|
esac
|
|
done <<< "$(read_strip_comments $KDUMP_CONF)"
|
|
}
|