1741 lines
		
	
	
		
			42 KiB
		
	
	
	
		
			C
		
	
	
	
	
	
			
		
		
	
	
			1741 lines
		
	
	
		
			42 KiB
		
	
	
	
		
			C
		
	
	
	
	
	
| // SPDX-License-Identifier: GPL-2.0-only
 | |
| /* Copyright (c) 2015, Sony Mobile Communications, AB.
 | |
|  */
 | |
| 
 | |
| #include <linux/delay.h>
 | |
| #include <linux/interrupt.h>
 | |
| #include <linux/ktime.h>
 | |
| #include <linux/kernel.h>
 | |
| #include <linux/backlight.h>
 | |
| #include <linux/module.h>
 | |
| #include <linux/of.h>
 | |
| #include <linux/of_device.h>
 | |
| #include <linux/of_address.h>
 | |
| #include <linux/regmap.h>
 | |
| 
 | |
| /* From DT binding */
 | |
| #define WLED_MAX_STRINGS				4
 | |
| #define MOD_A						0
 | |
| #define MOD_B						1
 | |
| 
 | |
| #define WLED_DEFAULT_BRIGHTNESS				2048
 | |
| #define WLED_SOFT_START_DLY_US				10000
 | |
| #define WLED3_SINK_REG_BRIGHT_MAX			0xFFF
 | |
| #define WLED5_SINK_REG_BRIGHT_MAX_12B			0xFFF
 | |
| #define WLED5_SINK_REG_BRIGHT_MAX_15B			0x7FFF
 | |
| 
 | |
| /* WLED3/WLED4 control registers */
 | |
| #define WLED3_CTRL_REG_FAULT_STATUS			0x08
 | |
| #define  WLED3_CTRL_REG_ILIM_FAULT_BIT			BIT(0)
 | |
| #define  WLED3_CTRL_REG_OVP_FAULT_BIT			BIT(1)
 | |
| #define  WLED4_CTRL_REG_SC_FAULT_BIT			BIT(2)
 | |
| #define  WLED5_CTRL_REG_OVP_PRE_ALARM_BIT		BIT(4)
 | |
| 
 | |
| #define WLED3_CTRL_REG_INT_RT_STS			0x10
 | |
| #define  WLED3_CTRL_REG_OVP_FAULT_STATUS		BIT(1)
 | |
| 
 | |
| #define WLED3_CTRL_REG_MOD_EN				0x46
 | |
| #define  WLED3_CTRL_REG_MOD_EN_MASK			BIT(7)
 | |
| #define  WLED3_CTRL_REG_MOD_EN_SHIFT			7
 | |
| 
 | |
| #define WLED3_CTRL_REG_FEEDBACK_CONTROL			0x48
 | |
| 
 | |
| #define WLED3_CTRL_REG_FREQ				0x4c
 | |
| #define  WLED3_CTRL_REG_FREQ_MASK			GENMASK(3, 0)
 | |
| 
 | |
| #define WLED3_CTRL_REG_OVP				0x4d
 | |
| #define  WLED3_CTRL_REG_OVP_MASK			GENMASK(1, 0)
 | |
| #define  WLED5_CTRL_REG_OVP_MASK			GENMASK(3, 0)
 | |
| 
 | |
| #define WLED3_CTRL_REG_ILIMIT				0x4e
 | |
| #define  WLED3_CTRL_REG_ILIMIT_MASK			GENMASK(2, 0)
 | |
| 
 | |
| /* WLED3/WLED4 sink registers */
 | |
| #define WLED3_SINK_REG_SYNC				0x47
 | |
| #define  WLED3_SINK_REG_SYNC_CLEAR			0x00
 | |
| 
 | |
| #define WLED3_SINK_REG_CURR_SINK			0x4f
 | |
| #define  WLED3_SINK_REG_CURR_SINK_MASK			GENMASK(7, 5)
 | |
| #define  WLED3_SINK_REG_CURR_SINK_SHFT			5
 | |
| 
 | |
| /* WLED3 specific per-'string' registers below */
 | |
| #define WLED3_SINK_REG_BRIGHT(n)			(0x40 + n)
 | |
| 
 | |
| #define WLED3_SINK_REG_STR_MOD_EN(n)			(0x60 + (n * 0x10))
 | |
| #define  WLED3_SINK_REG_STR_MOD_MASK			BIT(7)
 | |
| 
 | |
| #define WLED3_SINK_REG_STR_FULL_SCALE_CURR(n)		(0x62 + (n * 0x10))
 | |
| #define  WLED3_SINK_REG_STR_FULL_SCALE_CURR_MASK	GENMASK(4, 0)
 | |
| 
 | |
| #define WLED3_SINK_REG_STR_MOD_SRC(n)			(0x63 + (n * 0x10))
 | |
| #define  WLED3_SINK_REG_STR_MOD_SRC_MASK		BIT(0)
 | |
| #define  WLED3_SINK_REG_STR_MOD_SRC_INT			0x00
 | |
| #define  WLED3_SINK_REG_STR_MOD_SRC_EXT			0x01
 | |
| 
 | |
| #define WLED3_SINK_REG_STR_CABC(n)			(0x66 + (n * 0x10))
 | |
| #define  WLED3_SINK_REG_STR_CABC_MASK			BIT(7)
 | |
| 
 | |
| /* WLED4 specific control registers */
 | |
| #define WLED4_CTRL_REG_SHORT_PROTECT			0x5e
 | |
| #define  WLED4_CTRL_REG_SHORT_EN_MASK			BIT(7)
 | |
| 
 | |
| #define WLED4_CTRL_REG_SEC_ACCESS			0xd0
 | |
| #define  WLED4_CTRL_REG_SEC_UNLOCK			0xa5
 | |
| 
 | |
| #define WLED4_CTRL_REG_TEST1				0xe2
 | |
| #define  WLED4_CTRL_REG_TEST1_EXT_FET_DTEST2		0x09
 | |
| 
 | |
| /* WLED4 specific sink registers */
 | |
| #define WLED4_SINK_REG_CURR_SINK			0x46
 | |
| #define  WLED4_SINK_REG_CURR_SINK_MASK			GENMASK(7, 4)
 | |
| #define  WLED4_SINK_REG_CURR_SINK_SHFT			4
 | |
| 
 | |
| /* WLED4 specific per-'string' registers below */
 | |
| #define WLED4_SINK_REG_STR_MOD_EN(n)			(0x50 + (n * 0x10))
 | |
| #define  WLED4_SINK_REG_STR_MOD_MASK			BIT(7)
 | |
| 
 | |
| #define WLED4_SINK_REG_STR_FULL_SCALE_CURR(n)		(0x52 + (n * 0x10))
 | |
| #define  WLED4_SINK_REG_STR_FULL_SCALE_CURR_MASK	GENMASK(3, 0)
 | |
| 
 | |
| #define WLED4_SINK_REG_STR_MOD_SRC(n)			(0x53 + (n * 0x10))
 | |
| #define  WLED4_SINK_REG_STR_MOD_SRC_MASK		BIT(0)
 | |
| #define  WLED4_SINK_REG_STR_MOD_SRC_INT			0x00
 | |
| #define  WLED4_SINK_REG_STR_MOD_SRC_EXT			0x01
 | |
| 
 | |
| #define WLED4_SINK_REG_STR_CABC(n)			(0x56 + (n * 0x10))
 | |
| #define  WLED4_SINK_REG_STR_CABC_MASK			BIT(7)
 | |
| 
 | |
| #define WLED4_SINK_REG_BRIGHT(n)			(0x57 + (n * 0x10))
 | |
| 
 | |
| /* WLED5 specific control registers */
 | |
| #define WLED5_CTRL_REG_OVP_INT_CTL			0x5f
 | |
| #define  WLED5_CTRL_REG_OVP_INT_TIMER_MASK		GENMASK(2, 0)
 | |
| 
 | |
| /* WLED5 specific sink registers */
 | |
| #define WLED5_SINK_REG_MOD_A_EN				0x50
 | |
| #define WLED5_SINK_REG_MOD_B_EN				0x60
 | |
| #define  WLED5_SINK_REG_MOD_EN_MASK			BIT(7)
 | |
| 
 | |
| #define WLED5_SINK_REG_MOD_A_SRC_SEL			0x51
 | |
| #define WLED5_SINK_REG_MOD_B_SRC_SEL			0x61
 | |
| #define  WLED5_SINK_REG_MOD_SRC_SEL_HIGH		0
 | |
| #define  WLED5_SINK_REG_MOD_SRC_SEL_EXT			0x03
 | |
| #define  WLED5_SINK_REG_MOD_SRC_SEL_MASK		GENMASK(1, 0)
 | |
| 
 | |
| #define WLED5_SINK_REG_MOD_A_BRIGHTNESS_WIDTH_SEL	0x52
 | |
| #define WLED5_SINK_REG_MOD_B_BRIGHTNESS_WIDTH_SEL	0x62
 | |
| #define  WLED5_SINK_REG_BRIGHTNESS_WIDTH_12B		0
 | |
| #define  WLED5_SINK_REG_BRIGHTNESS_WIDTH_15B		1
 | |
| 
 | |
| #define WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB		0x53
 | |
| #define WLED5_SINK_REG_MOD_A_BRIGHTNESS_MSB		0x54
 | |
| #define WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB		0x63
 | |
| #define WLED5_SINK_REG_MOD_B_BRIGHTNESS_MSB		0x64
 | |
| 
 | |
| #define WLED5_SINK_REG_MOD_SYNC_BIT			0x65
 | |
| #define  WLED5_SINK_REG_SYNC_MOD_A_BIT			BIT(0)
 | |
| #define  WLED5_SINK_REG_SYNC_MOD_B_BIT			BIT(1)
 | |
| #define  WLED5_SINK_REG_SYNC_MASK			GENMASK(1, 0)
 | |
| 
 | |
| /* WLED5 specific per-'string' registers below */
 | |
| #define WLED5_SINK_REG_STR_FULL_SCALE_CURR(n)		(0x72 + (n * 0x10))
 | |
| 
 | |
| #define WLED5_SINK_REG_STR_SRC_SEL(n)			(0x73 + (n * 0x10))
 | |
| #define  WLED5_SINK_REG_SRC_SEL_MOD_A			0
 | |
| #define  WLED5_SINK_REG_SRC_SEL_MOD_B			1
 | |
| #define  WLED5_SINK_REG_SRC_SEL_MASK			GENMASK(1, 0)
 | |
| 
 | |
| struct wled_var_cfg {
 | |
| 	const u32 *values;
 | |
| 	u32 (*fn)(u32);
 | |
| 	int size;
 | |
| };
 | |
| 
 | |
| struct wled_u32_opts {
 | |
| 	const char *name;
 | |
| 	u32 *val_ptr;
 | |
| 	const struct wled_var_cfg *cfg;
 | |
| };
 | |
| 
 | |
| struct wled_bool_opts {
 | |
| 	const char *name;
 | |
| 	bool *val_ptr;
 | |
| };
 | |
| 
 | |
| struct wled_config {
 | |
| 	u32 boost_i_limit;
 | |
| 	u32 ovp;
 | |
| 	u32 switch_freq;
 | |
| 	u32 num_strings;
 | |
| 	u32 string_i_limit;
 | |
| 	u32 enabled_strings[WLED_MAX_STRINGS];
 | |
| 	u32 mod_sel;
 | |
| 	u32 cabc_sel;
 | |
| 	bool cs_out_en;
 | |
| 	bool ext_gen;
 | |
| 	bool cabc;
 | |
| 	bool external_pfet;
 | |
| 	bool auto_detection_enabled;
 | |
| };
 | |
| 
 | |
| struct wled {
 | |
| 	const char *name;
 | |
| 	struct device *dev;
 | |
| 	struct regmap *regmap;
 | |
| 	struct mutex lock;	/* Lock to avoid race from thread irq handler */
 | |
| 	ktime_t last_short_event;
 | |
| 	ktime_t start_ovp_fault_time;
 | |
| 	u16 ctrl_addr;
 | |
| 	u16 sink_addr;
 | |
| 	u16 max_string_count;
 | |
| 	u16 auto_detection_ovp_count;
 | |
| 	u32 brightness;
 | |
| 	u32 max_brightness;
 | |
| 	u32 short_count;
 | |
| 	u32 auto_detect_count;
 | |
| 	u32 version;
 | |
| 	bool disabled_by_short;
 | |
| 	bool has_short_detect;
 | |
| 	bool cabc_disabled;
 | |
| 	int short_irq;
 | |
| 	int ovp_irq;
 | |
| 
 | |
| 	struct wled_config cfg;
 | |
| 	struct delayed_work ovp_work;
 | |
| 
 | |
| 	/* Configures the brightness. Applicable for wled3, wled4 and wled5 */
 | |
| 	int (*wled_set_brightness)(struct wled *wled, u16 brightness);
 | |
| 
 | |
| 	/* Configures the cabc register. Applicable for wled4 and wled5 */
 | |
| 	int (*wled_cabc_config)(struct wled *wled, bool enable);
 | |
| 
 | |
| 	/*
 | |
| 	 * Toggles the sync bit for the brightness update to take place.
 | |
| 	 * Applicable for WLED3, WLED4 and WLED5.
 | |
| 	 */
 | |
| 	int (*wled_sync_toggle)(struct wled *wled);
 | |
| 
 | |
| 	/*
 | |
| 	 * Time to wait before checking the OVP status after wled module enable.
 | |
| 	 * Applicable for WLED4 and WLED5.
 | |
| 	 */
 | |
| 	int (*wled_ovp_delay)(struct wled *wled);
 | |
| 
 | |
| 	/*
 | |
| 	 * Determines if the auto string detection is required.
 | |
| 	 * Applicable for WLED4 and WLED5
 | |
| 	 */
 | |
| 	bool (*wled_auto_detection_required)(struct wled *wled);
 | |
| };
 | |
| 
 | |
| static int wled3_set_brightness(struct wled *wled, u16 brightness)
 | |
| {
 | |
| 	int rc, i;
 | |
| 	u8 v[2];
 | |
| 
 | |
| 	v[0] = brightness & 0xff;
 | |
| 	v[1] = (brightness >> 8) & 0xf;
 | |
| 
 | |
| 	for (i = 0;  i < wled->cfg.num_strings; ++i) {
 | |
| 		rc = regmap_bulk_write(wled->regmap, wled->ctrl_addr +
 | |
| 				       WLED3_SINK_REG_BRIGHT(i), v, 2);
 | |
| 		if (rc < 0)
 | |
| 			return rc;
 | |
| 	}
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static int wled4_set_brightness(struct wled *wled, u16 brightness)
 | |
| {
 | |
| 	int rc, i;
 | |
| 	u16 low_limit = wled->max_brightness * 4 / 1000;
 | |
| 	u8 v[2];
 | |
| 
 | |
| 	/* WLED4's lower limit of operation is 0.4% */
 | |
| 	if (brightness > 0 && brightness < low_limit)
 | |
| 		brightness = low_limit;
 | |
| 
 | |
| 	v[0] = brightness & 0xff;
 | |
| 	v[1] = (brightness >> 8) & 0xf;
 | |
| 
 | |
| 	for (i = 0;  i < wled->cfg.num_strings; ++i) {
 | |
| 		rc = regmap_bulk_write(wled->regmap, wled->sink_addr +
 | |
| 				       WLED4_SINK_REG_BRIGHT(i), v, 2);
 | |
| 		if (rc < 0)
 | |
| 			return rc;
 | |
| 	}
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static int wled5_set_brightness(struct wled *wled, u16 brightness)
 | |
| {
 | |
| 	int rc, offset;
 | |
| 	u16 low_limit = wled->max_brightness * 1 / 1000;
 | |
| 	u8 v[2];
 | |
| 
 | |
| 	/* WLED5's lower limit is 0.1% */
 | |
| 	if (brightness < low_limit)
 | |
| 		brightness = low_limit;
 | |
| 
 | |
| 	v[0] = brightness & 0xff;
 | |
| 	v[1] = (brightness >> 8) & 0x7f;
 | |
| 
 | |
| 	offset = (wled->cfg.mod_sel == MOD_A) ?
 | |
| 		  WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB :
 | |
| 		  WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB;
 | |
| 
 | |
| 	rc = regmap_bulk_write(wled->regmap, wled->sink_addr + offset,
 | |
| 			       v, 2);
 | |
| 	return rc;
 | |
| }
 | |
| 
 | |
| static void wled_ovp_work(struct work_struct *work)
 | |
| {
 | |
| 	struct wled *wled = container_of(work,
 | |
| 					 struct wled, ovp_work.work);
 | |
| 	enable_irq(wled->ovp_irq);
 | |
| }
 | |
| 
 | |
| static int wled_module_enable(struct wled *wled, int val)
 | |
| {
 | |
| 	int rc;
 | |
| 
 | |
| 	if (wled->disabled_by_short)
 | |
| 		return -ENXIO;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap, wled->ctrl_addr +
 | |
| 				WLED3_CTRL_REG_MOD_EN,
 | |
| 				WLED3_CTRL_REG_MOD_EN_MASK,
 | |
| 				val << WLED3_CTRL_REG_MOD_EN_SHIFT);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	if (wled->ovp_irq > 0) {
 | |
| 		if (val) {
 | |
| 			/*
 | |
| 			 * The hardware generates a storm of spurious OVP
 | |
| 			 * interrupts during soft start operations. So defer
 | |
| 			 * enabling the IRQ for 10ms to ensure that the
 | |
| 			 * soft start is complete.
 | |
| 			 */
 | |
| 			schedule_delayed_work(&wled->ovp_work, HZ / 100);
 | |
| 		} else {
 | |
| 			if (!cancel_delayed_work_sync(&wled->ovp_work))
 | |
| 				disable_irq(wled->ovp_irq);
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static int wled3_sync_toggle(struct wled *wled)
 | |
| {
 | |
| 	int rc;
 | |
| 	unsigned int mask = GENMASK(wled->max_string_count - 1, 0);
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->sink_addr + WLED3_SINK_REG_SYNC,
 | |
| 				mask, WLED3_SINK_REG_SYNC_CLEAR);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->sink_addr + WLED3_SINK_REG_SYNC,
 | |
| 				mask, mask);
 | |
| 
 | |
| 	return rc;
 | |
| }
 | |
| 
 | |
| static int wled5_mod_sync_toggle(struct wled *wled)
 | |
| {
 | |
| 	int rc;
 | |
| 	u8 val;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT,
 | |
| 				WLED5_SINK_REG_SYNC_MASK, 0);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_SYNC_MOD_A_BIT :
 | |
| 					     WLED5_SINK_REG_SYNC_MOD_B_BIT;
 | |
| 	return regmap_update_bits(wled->regmap,
 | |
| 				  wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT,
 | |
| 				  WLED5_SINK_REG_SYNC_MASK, val);
 | |
| }
 | |
| 
 | |
| static int wled_ovp_fault_status(struct wled *wled, bool *fault_set)
 | |
| {
 | |
| 	int rc;
 | |
| 	u32 int_rt_sts, fault_sts;
 | |
| 
 | |
| 	*fault_set = false;
 | |
| 	rc = regmap_read(wled->regmap,
 | |
| 			wled->ctrl_addr + WLED3_CTRL_REG_INT_RT_STS,
 | |
| 			&int_rt_sts);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Failed to read INT_RT_STS rc=%d\n", rc);
 | |
| 		return rc;
 | |
| 	}
 | |
| 
 | |
| 	rc = regmap_read(wled->regmap,
 | |
| 			wled->ctrl_addr + WLED3_CTRL_REG_FAULT_STATUS,
 | |
| 			&fault_sts);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Failed to read FAULT_STATUS rc=%d\n", rc);
 | |
| 		return rc;
 | |
| 	}
 | |
| 
 | |
| 	if (int_rt_sts & WLED3_CTRL_REG_OVP_FAULT_STATUS)
 | |
| 		*fault_set = true;
 | |
| 
 | |
| 	if (wled->version == 4 && (fault_sts & WLED3_CTRL_REG_OVP_FAULT_BIT))
 | |
| 		*fault_set = true;
 | |
| 
 | |
| 	if (wled->version == 5 && (fault_sts & (WLED3_CTRL_REG_OVP_FAULT_BIT |
 | |
| 				   WLED5_CTRL_REG_OVP_PRE_ALARM_BIT)))
 | |
| 		*fault_set = true;
 | |
| 
 | |
| 	if (*fault_set)
 | |
| 		dev_dbg(wled->dev, "WLED OVP fault detected, int_rt_sts=0x%x fault_sts=0x%x\n",
 | |
| 			int_rt_sts, fault_sts);
 | |
| 
 | |
| 	return rc;
 | |
| }
 | |
| 
 | |
| static int wled4_ovp_delay(struct wled *wled)
 | |
| {
 | |
| 	return WLED_SOFT_START_DLY_US;
 | |
| }
 | |
| 
 | |
| static int wled5_ovp_delay(struct wled *wled)
 | |
| {
 | |
| 	int rc, delay_us;
 | |
| 	u32 val;
 | |
| 	u8 ovp_timer_ms[8] = {1, 2, 4, 8, 12, 16, 20, 24};
 | |
| 
 | |
| 	/* For WLED5, get the delay based on OVP timer */
 | |
| 	rc = regmap_read(wled->regmap, wled->ctrl_addr +
 | |
| 			 WLED5_CTRL_REG_OVP_INT_CTL, &val);
 | |
| 	if (rc < 0)
 | |
| 		delay_us =
 | |
| 		ovp_timer_ms[val & WLED5_CTRL_REG_OVP_INT_TIMER_MASK] * 1000;
 | |
| 	else
 | |
| 		delay_us = 2 * WLED_SOFT_START_DLY_US;
 | |
| 
 | |
| 	dev_dbg(wled->dev, "delay_time_us: %d\n", delay_us);
 | |
| 
 | |
| 	return delay_us;
 | |
| }
 | |
| 
 | |
| static int wled_update_status(struct backlight_device *bl)
 | |
| {
 | |
| 	struct wled *wled = bl_get_data(bl);
 | |
| 	u16 brightness = backlight_get_brightness(bl);
 | |
| 	int rc = 0;
 | |
| 
 | |
| 	mutex_lock(&wled->lock);
 | |
| 	if (brightness) {
 | |
| 		rc = wled->wled_set_brightness(wled, brightness);
 | |
| 		if (rc < 0) {
 | |
| 			dev_err(wled->dev, "wled failed to set brightness rc:%d\n",
 | |
| 				rc);
 | |
| 			goto unlock_mutex;
 | |
| 		}
 | |
| 
 | |
| 		if (wled->version < 5) {
 | |
| 			rc = wled->wled_sync_toggle(wled);
 | |
| 			if (rc < 0) {
 | |
| 				dev_err(wled->dev, "wled sync failed rc:%d\n", rc);
 | |
| 				goto unlock_mutex;
 | |
| 			}
 | |
| 		} else {
 | |
| 			/*
 | |
| 			 * For WLED5 toggling the MOD_SYNC_BIT updates the
 | |
| 			 * brightness
 | |
| 			 */
 | |
| 			rc = wled5_mod_sync_toggle(wled);
 | |
| 			if (rc < 0) {
 | |
| 				dev_err(wled->dev, "wled mod sync failed rc:%d\n",
 | |
| 					rc);
 | |
| 				goto unlock_mutex;
 | |
| 			}
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	if (!!brightness != !!wled->brightness) {
 | |
| 		rc = wled_module_enable(wled, !!brightness);
 | |
| 		if (rc < 0) {
 | |
| 			dev_err(wled->dev, "wled enable failed rc:%d\n", rc);
 | |
| 			goto unlock_mutex;
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	wled->brightness = brightness;
 | |
| 
 | |
| unlock_mutex:
 | |
| 	mutex_unlock(&wled->lock);
 | |
| 
 | |
| 	return rc;
 | |
| }
 | |
| 
 | |
| static int wled4_cabc_config(struct wled *wled, bool enable)
 | |
| {
 | |
| 	int i, j, rc;
 | |
| 	u8 val;
 | |
| 
 | |
| 	for (i = 0; i < wled->cfg.num_strings; i++) {
 | |
| 		j = wled->cfg.enabled_strings[i];
 | |
| 
 | |
| 		val = enable ? WLED4_SINK_REG_STR_CABC_MASK : 0;
 | |
| 		rc = regmap_update_bits(wled->regmap, wled->sink_addr +
 | |
| 					WLED4_SINK_REG_STR_CABC(j),
 | |
| 					WLED4_SINK_REG_STR_CABC_MASK, val);
 | |
| 		if (rc < 0)
 | |
| 			return rc;
 | |
| 	}
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static int wled5_cabc_config(struct wled *wled, bool enable)
 | |
| {
 | |
| 	int rc, offset;
 | |
| 	u8 reg;
 | |
| 
 | |
| 	if (wled->cabc_disabled)
 | |
| 		return 0;
 | |
| 
 | |
| 	reg = enable ? wled->cfg.cabc_sel : 0;
 | |
| 	offset = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_MOD_A_SRC_SEL :
 | |
| 						WLED5_SINK_REG_MOD_B_SRC_SEL;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap, wled->sink_addr + offset,
 | |
| 				WLED5_SINK_REG_MOD_SRC_SEL_MASK, reg);
 | |
| 	if (rc < 0) {
 | |
| 		pr_err("Error in configuring CABC rc=%d\n", rc);
 | |
| 		return rc;
 | |
| 	}
 | |
| 
 | |
| 	if (!wled->cfg.cabc_sel)
 | |
| 		wled->cabc_disabled = true;
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| #define WLED_SHORT_DLY_MS			20
 | |
| #define WLED_SHORT_CNT_MAX			5
 | |
| #define WLED_SHORT_RESET_CNT_DLY_US		USEC_PER_SEC
 | |
| 
 | |
| static irqreturn_t wled_short_irq_handler(int irq, void *_wled)
 | |
| {
 | |
| 	struct wled *wled = _wled;
 | |
| 	int rc;
 | |
| 	s64 elapsed_time;
 | |
| 
 | |
| 	wled->short_count++;
 | |
| 	mutex_lock(&wled->lock);
 | |
| 	rc = wled_module_enable(wled, false);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "wled disable failed rc:%d\n", rc);
 | |
| 		goto unlock_mutex;
 | |
| 	}
 | |
| 
 | |
| 	elapsed_time = ktime_us_delta(ktime_get(),
 | |
| 				      wled->last_short_event);
 | |
| 	if (elapsed_time > WLED_SHORT_RESET_CNT_DLY_US)
 | |
| 		wled->short_count = 1;
 | |
| 
 | |
| 	if (wled->short_count > WLED_SHORT_CNT_MAX) {
 | |
| 		dev_err(wled->dev, "Short triggered %d times, disabling WLED forever!\n",
 | |
| 			wled->short_count);
 | |
| 		wled->disabled_by_short = true;
 | |
| 		goto unlock_mutex;
 | |
| 	}
 | |
| 
 | |
| 	wled->last_short_event = ktime_get();
 | |
| 
 | |
| 	msleep(WLED_SHORT_DLY_MS);
 | |
| 	rc = wled_module_enable(wled, true);
 | |
| 	if (rc < 0)
 | |
| 		dev_err(wled->dev, "wled enable failed rc:%d\n", rc);
 | |
| 
 | |
| unlock_mutex:
 | |
| 	mutex_unlock(&wled->lock);
 | |
| 
 | |
| 	return IRQ_HANDLED;
 | |
| }
 | |
| 
 | |
| #define AUTO_DETECT_BRIGHTNESS		200
 | |
| 
 | |
| static void wled_auto_string_detection(struct wled *wled)
 | |
| {
 | |
| 	int rc = 0, i, delay_time_us;
 | |
| 	u32 sink_config = 0;
 | |
| 	u8 sink_test = 0, sink_valid = 0, val;
 | |
| 	bool fault_set;
 | |
| 
 | |
| 	/* Read configured sink configuration */
 | |
| 	rc = regmap_read(wled->regmap, wled->sink_addr +
 | |
| 			 WLED4_SINK_REG_CURR_SINK, &sink_config);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Failed to read SINK configuration rc=%d\n",
 | |
| 			rc);
 | |
| 		goto failed_detect;
 | |
| 	}
 | |
| 
 | |
| 	/* Disable the module before starting detection */
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->ctrl_addr + WLED3_CTRL_REG_MOD_EN,
 | |
| 				WLED3_CTRL_REG_MOD_EN_MASK, 0);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Failed to disable WLED module rc=%d\n", rc);
 | |
| 		goto failed_detect;
 | |
| 	}
 | |
| 
 | |
| 	/* Set low brightness across all sinks */
 | |
| 	rc = wled4_set_brightness(wled, AUTO_DETECT_BRIGHTNESS);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Failed to set brightness for auto detection rc=%d\n",
 | |
| 			rc);
 | |
| 		goto failed_detect;
 | |
| 	}
 | |
| 
 | |
| 	if (wled->cfg.cabc) {
 | |
| 		rc = wled->wled_cabc_config(wled, false);
 | |
| 		if (rc < 0)
 | |
| 			goto failed_detect;
 | |
| 	}
 | |
| 
 | |
| 	/* Disable all sinks */
 | |
| 	rc = regmap_write(wled->regmap,
 | |
| 			  wled->sink_addr + WLED4_SINK_REG_CURR_SINK, 0);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Failed to disable all sinks rc=%d\n", rc);
 | |
| 		goto failed_detect;
 | |
| 	}
 | |
| 
 | |
| 	/* Iterate through the strings one by one */
 | |
| 	for (i = 0; i < wled->cfg.num_strings; i++) {
 | |
| 		sink_test = BIT((WLED4_SINK_REG_CURR_SINK_SHFT + i));
 | |
| 
 | |
| 		/* Enable feedback control */
 | |
| 		rc = regmap_write(wled->regmap, wled->ctrl_addr +
 | |
| 				  WLED3_CTRL_REG_FEEDBACK_CONTROL, i + 1);
 | |
| 		if (rc < 0) {
 | |
| 			dev_err(wled->dev, "Failed to enable feedback for SINK %d rc = %d\n",
 | |
| 				i + 1, rc);
 | |
| 			goto failed_detect;
 | |
| 		}
 | |
| 
 | |
| 		/* Enable the sink */
 | |
| 		rc = regmap_write(wled->regmap, wled->sink_addr +
 | |
| 				  WLED4_SINK_REG_CURR_SINK, sink_test);
 | |
| 		if (rc < 0) {
 | |
| 			dev_err(wled->dev, "Failed to configure SINK %d rc=%d\n",
 | |
| 				i + 1, rc);
 | |
| 			goto failed_detect;
 | |
| 		}
 | |
| 
 | |
| 		/* Enable the module */
 | |
| 		rc = regmap_update_bits(wled->regmap, wled->ctrl_addr +
 | |
| 					WLED3_CTRL_REG_MOD_EN,
 | |
| 					WLED3_CTRL_REG_MOD_EN_MASK,
 | |
| 					WLED3_CTRL_REG_MOD_EN_MASK);
 | |
| 		if (rc < 0) {
 | |
| 			dev_err(wled->dev, "Failed to enable WLED module rc=%d\n",
 | |
| 				rc);
 | |
| 			goto failed_detect;
 | |
| 		}
 | |
| 
 | |
| 		delay_time_us = wled->wled_ovp_delay(wled);
 | |
| 		usleep_range(delay_time_us, delay_time_us + 1000);
 | |
| 
 | |
| 		rc = wled_ovp_fault_status(wled, &fault_set);
 | |
| 		if (rc < 0) {
 | |
| 			dev_err(wled->dev, "Error in getting OVP fault_sts, rc=%d\n",
 | |
| 				rc);
 | |
| 			goto failed_detect;
 | |
| 		}
 | |
| 
 | |
| 		if (fault_set)
 | |
| 			dev_dbg(wled->dev, "WLED OVP fault detected with SINK %d\n",
 | |
| 				i + 1);
 | |
| 		else
 | |
| 			sink_valid |= sink_test;
 | |
| 
 | |
| 		/* Disable the module */
 | |
| 		rc = regmap_update_bits(wled->regmap,
 | |
| 					wled->ctrl_addr + WLED3_CTRL_REG_MOD_EN,
 | |
| 					WLED3_CTRL_REG_MOD_EN_MASK, 0);
 | |
| 		if (rc < 0) {
 | |
| 			dev_err(wled->dev, "Failed to disable WLED module rc=%d\n",
 | |
| 				rc);
 | |
| 			goto failed_detect;
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	if (!sink_valid) {
 | |
| 		dev_err(wled->dev, "No valid WLED sinks found\n");
 | |
| 		wled->disabled_by_short = true;
 | |
| 		goto failed_detect;
 | |
| 	}
 | |
| 
 | |
| 	if (sink_valid != sink_config) {
 | |
| 		dev_warn(wled->dev, "%x is not a valid sink configuration - using %x instead\n",
 | |
| 			 sink_config, sink_valid);
 | |
| 		sink_config = sink_valid;
 | |
| 	}
 | |
| 
 | |
| 	/* Write the new sink configuration */
 | |
| 	rc = regmap_write(wled->regmap,
 | |
| 			  wled->sink_addr + WLED4_SINK_REG_CURR_SINK,
 | |
| 			  sink_config);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Failed to reconfigure the default sink rc=%d\n",
 | |
| 			rc);
 | |
| 		goto failed_detect;
 | |
| 	}
 | |
| 
 | |
| 	/* Enable valid sinks */
 | |
| 	if (wled->version == 4) {
 | |
| 		for (i = 0; i < wled->cfg.num_strings; i++) {
 | |
| 			if (sink_config &
 | |
| 			    BIT(WLED4_SINK_REG_CURR_SINK_SHFT + i))
 | |
| 				val = WLED4_SINK_REG_STR_MOD_MASK;
 | |
| 			else
 | |
| 				/* Disable modulator_en for unused sink */
 | |
| 				val = 0;
 | |
| 
 | |
| 			rc = regmap_write(wled->regmap, wled->sink_addr +
 | |
| 					  WLED4_SINK_REG_STR_MOD_EN(i), val);
 | |
| 			if (rc < 0) {
 | |
| 				dev_err(wled->dev, "Failed to configure MODULATOR_EN rc=%d\n",
 | |
| 					rc);
 | |
| 				goto failed_detect;
 | |
| 			}
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	/* Enable CABC */
 | |
| 	rc = wled->wled_cabc_config(wled, true);
 | |
| 	if (rc < 0)
 | |
| 		goto failed_detect;
 | |
| 
 | |
| 	/* Restore the feedback setting */
 | |
| 	rc = regmap_write(wled->regmap,
 | |
| 			  wled->ctrl_addr + WLED3_CTRL_REG_FEEDBACK_CONTROL, 0);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Failed to restore feedback setting rc=%d\n",
 | |
| 			rc);
 | |
| 		goto failed_detect;
 | |
| 	}
 | |
| 
 | |
| 	/* Restore brightness */
 | |
| 	rc = wled4_set_brightness(wled, wled->brightness);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Failed to set brightness after auto detection rc=%d\n",
 | |
| 			rc);
 | |
| 		goto failed_detect;
 | |
| 	}
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->ctrl_addr + WLED3_CTRL_REG_MOD_EN,
 | |
| 				WLED3_CTRL_REG_MOD_EN_MASK,
 | |
| 				WLED3_CTRL_REG_MOD_EN_MASK);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Failed to enable WLED module rc=%d\n", rc);
 | |
| 		goto failed_detect;
 | |
| 	}
 | |
| 
 | |
| failed_detect:
 | |
| 	return;
 | |
| }
 | |
| 
 | |
| #define WLED_AUTO_DETECT_OVP_COUNT		5
 | |
| #define WLED_AUTO_DETECT_CNT_DLY_US		USEC_PER_SEC
 | |
| 
 | |
| static bool wled4_auto_detection_required(struct wled *wled)
 | |
| {
 | |
| 	s64 elapsed_time_us;
 | |
| 
 | |
| 	if (!wled->cfg.auto_detection_enabled)
 | |
| 		return false;
 | |
| 
 | |
| 	/*
 | |
| 	 * Check if the OVP fault was an occasional one
 | |
| 	 * or if it's firing continuously, the latter qualifies
 | |
| 	 * for an auto-detection check.
 | |
| 	 */
 | |
| 	if (!wled->auto_detection_ovp_count) {
 | |
| 		wled->start_ovp_fault_time = ktime_get();
 | |
| 		wled->auto_detection_ovp_count++;
 | |
| 	} else {
 | |
| 		elapsed_time_us = ktime_us_delta(ktime_get(),
 | |
| 						 wled->start_ovp_fault_time);
 | |
| 		if (elapsed_time_us > WLED_AUTO_DETECT_CNT_DLY_US)
 | |
| 			wled->auto_detection_ovp_count = 0;
 | |
| 		else
 | |
| 			wled->auto_detection_ovp_count++;
 | |
| 
 | |
| 		if (wled->auto_detection_ovp_count >=
 | |
| 				WLED_AUTO_DETECT_OVP_COUNT) {
 | |
| 			wled->auto_detection_ovp_count = 0;
 | |
| 			return true;
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	return false;
 | |
| }
 | |
| 
 | |
| static bool wled5_auto_detection_required(struct wled *wled)
 | |
| {
 | |
| 	if (!wled->cfg.auto_detection_enabled)
 | |
| 		return false;
 | |
| 
 | |
| 	/*
 | |
| 	 * Unlike WLED4, WLED5 has OVP fault density interrupt configuration
 | |
| 	 * i.e. to count the number of OVP alarms for a certain duration before
 | |
| 	 * triggering OVP fault interrupt. By default, number of OVP fault
 | |
| 	 * events counted before an interrupt is fired is 32 and the time
 | |
| 	 * interval is 12 ms. If we see one OVP fault interrupt, then that
 | |
| 	 * should qualify for a real OVP fault condition to run auto detection
 | |
| 	 * algorithm.
 | |
| 	 */
 | |
| 	return true;
 | |
| }
 | |
| 
 | |
| static int wled_auto_detection_at_init(struct wled *wled)
 | |
| {
 | |
| 	int rc;
 | |
| 	bool fault_set;
 | |
| 
 | |
| 	if (!wled->cfg.auto_detection_enabled)
 | |
| 		return 0;
 | |
| 
 | |
| 	rc = wled_ovp_fault_status(wled, &fault_set);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Error in getting OVP fault_sts, rc=%d\n",
 | |
| 			rc);
 | |
| 		return rc;
 | |
| 	}
 | |
| 
 | |
| 	if (fault_set) {
 | |
| 		mutex_lock(&wled->lock);
 | |
| 		wled_auto_string_detection(wled);
 | |
| 		mutex_unlock(&wled->lock);
 | |
| 	}
 | |
| 
 | |
| 	return rc;
 | |
| }
 | |
| 
 | |
| static irqreturn_t wled_ovp_irq_handler(int irq, void *_wled)
 | |
| {
 | |
| 	struct wled *wled = _wled;
 | |
| 	int rc;
 | |
| 	u32 int_sts, fault_sts;
 | |
| 
 | |
| 	rc = regmap_read(wled->regmap,
 | |
| 			 wled->ctrl_addr + WLED3_CTRL_REG_INT_RT_STS, &int_sts);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Error in reading WLED3_INT_RT_STS rc=%d\n",
 | |
| 			rc);
 | |
| 		return IRQ_HANDLED;
 | |
| 	}
 | |
| 
 | |
| 	rc = regmap_read(wled->regmap, wled->ctrl_addr +
 | |
| 			 WLED3_CTRL_REG_FAULT_STATUS, &fault_sts);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Error in reading WLED_FAULT_STATUS rc=%d\n",
 | |
| 			rc);
 | |
| 		return IRQ_HANDLED;
 | |
| 	}
 | |
| 
 | |
| 	if (fault_sts & (WLED3_CTRL_REG_OVP_FAULT_BIT |
 | |
| 		WLED3_CTRL_REG_ILIM_FAULT_BIT))
 | |
| 		dev_dbg(wled->dev, "WLED OVP fault detected, int_sts=%x fault_sts= %x\n",
 | |
| 			int_sts, fault_sts);
 | |
| 
 | |
| 	if (fault_sts & WLED3_CTRL_REG_OVP_FAULT_BIT) {
 | |
| 		if (wled->wled_auto_detection_required(wled)) {
 | |
| 			mutex_lock(&wled->lock);
 | |
| 			wled_auto_string_detection(wled);
 | |
| 			mutex_unlock(&wled->lock);
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	return IRQ_HANDLED;
 | |
| }
 | |
| 
 | |
| static int wled3_setup(struct wled *wled)
 | |
| {
 | |
| 	u16 addr;
 | |
| 	u8 sink_en = 0;
 | |
| 	int rc, i, j;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->ctrl_addr + WLED3_CTRL_REG_OVP,
 | |
| 				WLED3_CTRL_REG_OVP_MASK, wled->cfg.ovp);
 | |
| 	if (rc)
 | |
| 		return rc;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->ctrl_addr + WLED3_CTRL_REG_ILIMIT,
 | |
| 				WLED3_CTRL_REG_ILIMIT_MASK,
 | |
| 				wled->cfg.boost_i_limit);
 | |
| 	if (rc)
 | |
| 		return rc;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->ctrl_addr + WLED3_CTRL_REG_FREQ,
 | |
| 				WLED3_CTRL_REG_FREQ_MASK,
 | |
| 				wled->cfg.switch_freq);
 | |
| 	if (rc)
 | |
| 		return rc;
 | |
| 
 | |
| 	for (i = 0; i < wled->cfg.num_strings; ++i) {
 | |
| 		j = wled->cfg.enabled_strings[i];
 | |
| 		addr = wled->ctrl_addr + WLED3_SINK_REG_STR_MOD_EN(j);
 | |
| 		rc = regmap_update_bits(wled->regmap, addr,
 | |
| 					WLED3_SINK_REG_STR_MOD_MASK,
 | |
| 					WLED3_SINK_REG_STR_MOD_MASK);
 | |
| 		if (rc)
 | |
| 			return rc;
 | |
| 
 | |
| 		if (wled->cfg.ext_gen) {
 | |
| 			addr = wled->ctrl_addr + WLED3_SINK_REG_STR_MOD_SRC(j);
 | |
| 			rc = regmap_update_bits(wled->regmap, addr,
 | |
| 						WLED3_SINK_REG_STR_MOD_SRC_MASK,
 | |
| 						WLED3_SINK_REG_STR_MOD_SRC_EXT);
 | |
| 			if (rc)
 | |
| 				return rc;
 | |
| 		}
 | |
| 
 | |
| 		addr = wled->ctrl_addr + WLED3_SINK_REG_STR_FULL_SCALE_CURR(j);
 | |
| 		rc = regmap_update_bits(wled->regmap, addr,
 | |
| 					WLED3_SINK_REG_STR_FULL_SCALE_CURR_MASK,
 | |
| 					wled->cfg.string_i_limit);
 | |
| 		if (rc)
 | |
| 			return rc;
 | |
| 
 | |
| 		addr = wled->ctrl_addr + WLED3_SINK_REG_STR_CABC(j);
 | |
| 		rc = regmap_update_bits(wled->regmap, addr,
 | |
| 					WLED3_SINK_REG_STR_CABC_MASK,
 | |
| 					wled->cfg.cabc ?
 | |
| 					WLED3_SINK_REG_STR_CABC_MASK : 0);
 | |
| 		if (rc)
 | |
| 			return rc;
 | |
| 
 | |
| 		sink_en |= BIT(j + WLED3_SINK_REG_CURR_SINK_SHFT);
 | |
| 	}
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->ctrl_addr + WLED3_SINK_REG_CURR_SINK,
 | |
| 				WLED3_SINK_REG_CURR_SINK_MASK, sink_en);
 | |
| 	if (rc)
 | |
| 		return rc;
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static const struct wled_config wled3_config_defaults = {
 | |
| 	.boost_i_limit = 3,
 | |
| 	.string_i_limit = 20,
 | |
| 	.ovp = 2,
 | |
| 	.num_strings = 3,
 | |
| 	.switch_freq = 5,
 | |
| 	.cs_out_en = false,
 | |
| 	.ext_gen = false,
 | |
| 	.cabc = false,
 | |
| 	.enabled_strings = {0, 1, 2, 3},
 | |
| };
 | |
| 
 | |
| static int wled4_setup(struct wled *wled)
 | |
| {
 | |
| 	int rc, temp, i, j;
 | |
| 	u16 addr;
 | |
| 	u8 sink_en = 0;
 | |
| 	u32 sink_cfg;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->ctrl_addr + WLED3_CTRL_REG_OVP,
 | |
| 				WLED3_CTRL_REG_OVP_MASK, wled->cfg.ovp);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->ctrl_addr + WLED3_CTRL_REG_ILIMIT,
 | |
| 				WLED3_CTRL_REG_ILIMIT_MASK,
 | |
| 				wled->cfg.boost_i_limit);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->ctrl_addr + WLED3_CTRL_REG_FREQ,
 | |
| 				WLED3_CTRL_REG_FREQ_MASK,
 | |
| 				wled->cfg.switch_freq);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	if (wled->cfg.external_pfet) {
 | |
| 		/* Unlock the secure register access */
 | |
| 		rc = regmap_write(wled->regmap, wled->ctrl_addr +
 | |
| 				  WLED4_CTRL_REG_SEC_ACCESS,
 | |
| 				  WLED4_CTRL_REG_SEC_UNLOCK);
 | |
| 		if (rc < 0)
 | |
| 			return rc;
 | |
| 
 | |
| 		rc = regmap_write(wled->regmap,
 | |
| 				  wled->ctrl_addr + WLED4_CTRL_REG_TEST1,
 | |
| 				  WLED4_CTRL_REG_TEST1_EXT_FET_DTEST2);
 | |
| 		if (rc < 0)
 | |
| 			return rc;
 | |
| 	}
 | |
| 
 | |
| 	rc = regmap_read(wled->regmap, wled->sink_addr +
 | |
| 			 WLED4_SINK_REG_CURR_SINK, &sink_cfg);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	for (i = 0; i < wled->cfg.num_strings; i++) {
 | |
| 		j = wled->cfg.enabled_strings[i];
 | |
| 		temp = j + WLED4_SINK_REG_CURR_SINK_SHFT;
 | |
| 		sink_en |= 1 << temp;
 | |
| 	}
 | |
| 
 | |
| 	if (sink_cfg == sink_en) {
 | |
| 		rc = wled_auto_detection_at_init(wled);
 | |
| 		return rc;
 | |
| 	}
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->sink_addr + WLED4_SINK_REG_CURR_SINK,
 | |
| 				WLED4_SINK_REG_CURR_SINK_MASK, 0);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap, wled->ctrl_addr +
 | |
| 				WLED3_CTRL_REG_MOD_EN,
 | |
| 				WLED3_CTRL_REG_MOD_EN_MASK, 0);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	/* Per sink/string configuration */
 | |
| 	for (i = 0; i < wled->cfg.num_strings; i++) {
 | |
| 		j = wled->cfg.enabled_strings[i];
 | |
| 
 | |
| 		addr = wled->sink_addr +
 | |
| 				WLED4_SINK_REG_STR_MOD_EN(j);
 | |
| 		rc = regmap_update_bits(wled->regmap, addr,
 | |
| 					WLED4_SINK_REG_STR_MOD_MASK,
 | |
| 					WLED4_SINK_REG_STR_MOD_MASK);
 | |
| 		if (rc < 0)
 | |
| 			return rc;
 | |
| 
 | |
| 		addr = wled->sink_addr +
 | |
| 				WLED4_SINK_REG_STR_FULL_SCALE_CURR(j);
 | |
| 		rc = regmap_update_bits(wled->regmap, addr,
 | |
| 					WLED4_SINK_REG_STR_FULL_SCALE_CURR_MASK,
 | |
| 					wled->cfg.string_i_limit);
 | |
| 		if (rc < 0)
 | |
| 			return rc;
 | |
| 	}
 | |
| 
 | |
| 	rc = wled4_cabc_config(wled, wled->cfg.cabc);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap, wled->ctrl_addr +
 | |
| 				WLED3_CTRL_REG_MOD_EN,
 | |
| 				WLED3_CTRL_REG_MOD_EN_MASK,
 | |
| 				WLED3_CTRL_REG_MOD_EN_MASK);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->sink_addr + WLED4_SINK_REG_CURR_SINK,
 | |
| 				WLED4_SINK_REG_CURR_SINK_MASK, sink_en);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	rc = wled->wled_sync_toggle(wled);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Failed to toggle sync reg rc:%d\n", rc);
 | |
| 		return rc;
 | |
| 	}
 | |
| 
 | |
| 	rc = wled_auto_detection_at_init(wled);
 | |
| 
 | |
| 	return rc;
 | |
| }
 | |
| 
 | |
| static const struct wled_config wled4_config_defaults = {
 | |
| 	.boost_i_limit = 4,
 | |
| 	.string_i_limit = 10,
 | |
| 	.ovp = 1,
 | |
| 	.num_strings = 4,
 | |
| 	.switch_freq = 11,
 | |
| 	.cabc = false,
 | |
| 	.external_pfet = false,
 | |
| 	.auto_detection_enabled = false,
 | |
| };
 | |
| 
 | |
| static int wled5_setup(struct wled *wled)
 | |
| {
 | |
| 	int rc, temp, i, j, offset;
 | |
| 	u8 sink_en = 0;
 | |
| 	u16 addr;
 | |
| 	u32 val;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->ctrl_addr + WLED3_CTRL_REG_OVP,
 | |
| 				WLED5_CTRL_REG_OVP_MASK, wled->cfg.ovp);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->ctrl_addr + WLED3_CTRL_REG_ILIMIT,
 | |
| 				WLED3_CTRL_REG_ILIMIT_MASK,
 | |
| 				wled->cfg.boost_i_limit);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->ctrl_addr + WLED3_CTRL_REG_FREQ,
 | |
| 				WLED3_CTRL_REG_FREQ_MASK,
 | |
| 				wled->cfg.switch_freq);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	/* Per sink/string configuration */
 | |
| 	for (i = 0; i < wled->cfg.num_strings; ++i) {
 | |
| 		j = wled->cfg.enabled_strings[i];
 | |
| 		addr = wled->sink_addr +
 | |
| 				WLED4_SINK_REG_STR_FULL_SCALE_CURR(j);
 | |
| 		rc = regmap_update_bits(wled->regmap, addr,
 | |
| 					WLED4_SINK_REG_STR_FULL_SCALE_CURR_MASK,
 | |
| 					wled->cfg.string_i_limit);
 | |
| 		if (rc < 0)
 | |
| 			return rc;
 | |
| 
 | |
| 		addr = wled->sink_addr + WLED5_SINK_REG_STR_SRC_SEL(j);
 | |
| 		rc = regmap_update_bits(wled->regmap, addr,
 | |
| 					WLED5_SINK_REG_SRC_SEL_MASK,
 | |
| 					wled->cfg.mod_sel == MOD_A ?
 | |
| 					WLED5_SINK_REG_SRC_SEL_MOD_A :
 | |
| 					WLED5_SINK_REG_SRC_SEL_MOD_B);
 | |
| 
 | |
| 		temp = j + WLED4_SINK_REG_CURR_SINK_SHFT;
 | |
| 		sink_en |= 1 << temp;
 | |
| 	}
 | |
| 
 | |
| 	rc = wled5_cabc_config(wled, wled->cfg.cabc_sel ? true : false);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	/* Enable one of the modulators A or B based on mod_sel */
 | |
| 	addr = wled->sink_addr + WLED5_SINK_REG_MOD_A_EN;
 | |
| 	val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_MOD_EN_MASK : 0;
 | |
| 	rc = regmap_update_bits(wled->regmap, addr,
 | |
| 				WLED5_SINK_REG_MOD_EN_MASK, val);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	addr = wled->sink_addr + WLED5_SINK_REG_MOD_B_EN;
 | |
| 	val = (wled->cfg.mod_sel == MOD_B) ? WLED5_SINK_REG_MOD_EN_MASK : 0;
 | |
| 	rc = regmap_update_bits(wled->regmap, addr,
 | |
| 				WLED5_SINK_REG_MOD_EN_MASK, val);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	offset = (wled->cfg.mod_sel == MOD_A) ?
 | |
| 		  WLED5_SINK_REG_MOD_A_BRIGHTNESS_WIDTH_SEL :
 | |
| 		  WLED5_SINK_REG_MOD_B_BRIGHTNESS_WIDTH_SEL;
 | |
| 
 | |
| 	addr = wled->sink_addr + offset;
 | |
| 	val = (wled->max_brightness == WLED5_SINK_REG_BRIGHT_MAX_15B) ?
 | |
| 		 WLED5_SINK_REG_BRIGHTNESS_WIDTH_15B :
 | |
| 		 WLED5_SINK_REG_BRIGHTNESS_WIDTH_12B;
 | |
| 	rc = regmap_write(wled->regmap, addr, val);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap,
 | |
| 				wled->sink_addr + WLED4_SINK_REG_CURR_SINK,
 | |
| 				WLED4_SINK_REG_CURR_SINK_MASK, sink_en);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	/* This updates only FSC configuration in WLED5 */
 | |
| 	rc = wled->wled_sync_toggle(wled);
 | |
| 	if (rc < 0) {
 | |
| 		pr_err("Failed to toggle sync reg rc:%d\n", rc);
 | |
| 		return rc;
 | |
| 	}
 | |
| 
 | |
| 	rc = wled_auto_detection_at_init(wled);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static const struct wled_config wled5_config_defaults = {
 | |
| 	.boost_i_limit = 5,
 | |
| 	.string_i_limit = 10,
 | |
| 	.ovp = 4,
 | |
| 	.num_strings = 4,
 | |
| 	.switch_freq = 11,
 | |
| 	.mod_sel = 0,
 | |
| 	.cabc_sel = 0,
 | |
| 	.cabc = false,
 | |
| 	.external_pfet = false,
 | |
| 	.auto_detection_enabled = false,
 | |
| };
 | |
| 
 | |
| static const u32 wled3_boost_i_limit_values[] = {
 | |
| 	105, 385, 525, 805, 980, 1260, 1400, 1680,
 | |
| };
 | |
| 
 | |
| static const struct wled_var_cfg wled3_boost_i_limit_cfg = {
 | |
| 	.values = wled3_boost_i_limit_values,
 | |
| 	.size = ARRAY_SIZE(wled3_boost_i_limit_values),
 | |
| };
 | |
| 
 | |
| static const u32 wled4_boost_i_limit_values[] = {
 | |
| 	105, 280, 450, 620, 970, 1150, 1300, 1500,
 | |
| };
 | |
| 
 | |
| static const struct wled_var_cfg wled4_boost_i_limit_cfg = {
 | |
| 	.values = wled4_boost_i_limit_values,
 | |
| 	.size = ARRAY_SIZE(wled4_boost_i_limit_values),
 | |
| };
 | |
| 
 | |
| static inline u32 wled5_boost_i_limit_values_fn(u32 idx)
 | |
| {
 | |
| 	return 525 + (idx * 175);
 | |
| }
 | |
| 
 | |
| static const struct wled_var_cfg wled5_boost_i_limit_cfg = {
 | |
| 	.fn = wled5_boost_i_limit_values_fn,
 | |
| 	.size = 8,
 | |
| };
 | |
| 
 | |
| static const u32 wled3_ovp_values[] = {
 | |
| 	35, 32, 29, 27,
 | |
| };
 | |
| 
 | |
| static const struct wled_var_cfg wled3_ovp_cfg = {
 | |
| 	.values = wled3_ovp_values,
 | |
| 	.size = ARRAY_SIZE(wled3_ovp_values),
 | |
| };
 | |
| 
 | |
| static const u32 wled4_ovp_values[] = {
 | |
| 	31100, 29600, 19600, 18100,
 | |
| };
 | |
| 
 | |
| static const struct wled_var_cfg wled4_ovp_cfg = {
 | |
| 	.values = wled4_ovp_values,
 | |
| 	.size = ARRAY_SIZE(wled4_ovp_values),
 | |
| };
 | |
| 
 | |
| static inline u32 wled5_ovp_values_fn(u32 idx)
 | |
| {
 | |
| 	/*
 | |
| 	 * 0000 - 38.5 V
 | |
| 	 * 0001 - 37 V ..
 | |
| 	 * 1111 - 16 V
 | |
| 	 */
 | |
| 	return 38500 - (idx * 1500);
 | |
| }
 | |
| 
 | |
| static const struct wled_var_cfg wled5_ovp_cfg = {
 | |
| 	.fn = wled5_ovp_values_fn,
 | |
| 	.size = 16,
 | |
| };
 | |
| 
 | |
| static u32 wled3_num_strings_values_fn(u32 idx)
 | |
| {
 | |
| 	return idx + 1;
 | |
| }
 | |
| 
 | |
| static const struct wled_var_cfg wled3_num_strings_cfg = {
 | |
| 	.fn = wled3_num_strings_values_fn,
 | |
| 	.size = 3,
 | |
| };
 | |
| 
 | |
| static const struct wled_var_cfg wled4_num_strings_cfg = {
 | |
| 	.fn = wled3_num_strings_values_fn,
 | |
| 	.size = 4,
 | |
| };
 | |
| 
 | |
| static u32 wled3_switch_freq_values_fn(u32 idx)
 | |
| {
 | |
| 	return 19200 / (2 * (1 + idx));
 | |
| }
 | |
| 
 | |
| static const struct wled_var_cfg wled3_switch_freq_cfg = {
 | |
| 	.fn = wled3_switch_freq_values_fn,
 | |
| 	.size = 16,
 | |
| };
 | |
| 
 | |
| static const struct wled_var_cfg wled3_string_i_limit_cfg = {
 | |
| 	.size = 26,
 | |
| };
 | |
| 
 | |
| static const u32 wled4_string_i_limit_values[] = {
 | |
| 	0, 2500, 5000, 7500, 10000, 12500, 15000, 17500, 20000,
 | |
| 	22500, 25000, 27500, 30000,
 | |
| };
 | |
| 
 | |
| static const struct wled_var_cfg wled4_string_i_limit_cfg = {
 | |
| 	.values = wled4_string_i_limit_values,
 | |
| 	.size = ARRAY_SIZE(wled4_string_i_limit_values),
 | |
| };
 | |
| 
 | |
| static const struct wled_var_cfg wled5_mod_sel_cfg = {
 | |
| 	.size = 2,
 | |
| };
 | |
| 
 | |
| static const struct wled_var_cfg wled5_cabc_sel_cfg = {
 | |
| 	.size = 4,
 | |
| };
 | |
| 
 | |
| static u32 wled_values(const struct wled_var_cfg *cfg, u32 idx)
 | |
| {
 | |
| 	if (idx >= cfg->size)
 | |
| 		return UINT_MAX;
 | |
| 	if (cfg->fn)
 | |
| 		return cfg->fn(idx);
 | |
| 	if (cfg->values)
 | |
| 		return cfg->values[idx];
 | |
| 	return idx;
 | |
| }
 | |
| 
 | |
| static int wled_configure(struct wled *wled)
 | |
| {
 | |
| 	struct wled_config *cfg = &wled->cfg;
 | |
| 	struct device *dev = wled->dev;
 | |
| 	const __be32 *prop_addr;
 | |
| 	u32 size, val, c;
 | |
| 	int rc, i, j, string_len;
 | |
| 
 | |
| 	const struct wled_u32_opts *u32_opts = NULL;
 | |
| 	const struct wled_u32_opts wled3_opts[] = {
 | |
| 		{
 | |
| 			.name = "qcom,current-boost-limit",
 | |
| 			.val_ptr = &cfg->boost_i_limit,
 | |
| 			.cfg = &wled3_boost_i_limit_cfg,
 | |
| 		},
 | |
| 		{
 | |
| 			.name = "qcom,current-limit",
 | |
| 			.val_ptr = &cfg->string_i_limit,
 | |
| 			.cfg = &wled3_string_i_limit_cfg,
 | |
| 		},
 | |
| 		{
 | |
| 			.name = "qcom,ovp",
 | |
| 			.val_ptr = &cfg->ovp,
 | |
| 			.cfg = &wled3_ovp_cfg,
 | |
| 		},
 | |
| 		{
 | |
| 			.name = "qcom,switching-freq",
 | |
| 			.val_ptr = &cfg->switch_freq,
 | |
| 			.cfg = &wled3_switch_freq_cfg,
 | |
| 		},
 | |
| 		{
 | |
| 			.name = "qcom,num-strings",
 | |
| 			.val_ptr = &cfg->num_strings,
 | |
| 			.cfg = &wled3_num_strings_cfg,
 | |
| 		},
 | |
| 	};
 | |
| 
 | |
| 	const struct wled_u32_opts wled4_opts[] = {
 | |
| 		{
 | |
| 			.name = "qcom,current-boost-limit",
 | |
| 			.val_ptr = &cfg->boost_i_limit,
 | |
| 			.cfg = &wled4_boost_i_limit_cfg,
 | |
| 		},
 | |
| 		{
 | |
| 			.name = "qcom,current-limit-microamp",
 | |
| 			.val_ptr = &cfg->string_i_limit,
 | |
| 			.cfg = &wled4_string_i_limit_cfg,
 | |
| 		},
 | |
| 		{
 | |
| 			.name = "qcom,ovp-millivolt",
 | |
| 			.val_ptr = &cfg->ovp,
 | |
| 			.cfg = &wled4_ovp_cfg,
 | |
| 		},
 | |
| 		{
 | |
| 			.name = "qcom,switching-freq",
 | |
| 			.val_ptr = &cfg->switch_freq,
 | |
| 			.cfg = &wled3_switch_freq_cfg,
 | |
| 		},
 | |
| 		{
 | |
| 			.name = "qcom,num-strings",
 | |
| 			.val_ptr = &cfg->num_strings,
 | |
| 			.cfg = &wled4_num_strings_cfg,
 | |
| 		},
 | |
| 	};
 | |
| 
 | |
| 	const struct wled_u32_opts wled5_opts[] = {
 | |
| 		{
 | |
| 			.name = "qcom,current-boost-limit",
 | |
| 			.val_ptr = &cfg->boost_i_limit,
 | |
| 			.cfg = &wled5_boost_i_limit_cfg,
 | |
| 		},
 | |
| 		{
 | |
| 			.name = "qcom,current-limit-microamp",
 | |
| 			.val_ptr = &cfg->string_i_limit,
 | |
| 			.cfg = &wled4_string_i_limit_cfg,
 | |
| 		},
 | |
| 		{
 | |
| 			.name = "qcom,ovp-millivolt",
 | |
| 			.val_ptr = &cfg->ovp,
 | |
| 			.cfg = &wled5_ovp_cfg,
 | |
| 		},
 | |
| 		{
 | |
| 			.name = "qcom,switching-freq",
 | |
| 			.val_ptr = &cfg->switch_freq,
 | |
| 			.cfg = &wled3_switch_freq_cfg,
 | |
| 		},
 | |
| 		{
 | |
| 			.name = "qcom,num-strings",
 | |
| 			.val_ptr = &cfg->num_strings,
 | |
| 			.cfg = &wled4_num_strings_cfg,
 | |
| 		},
 | |
| 		{
 | |
| 			.name = "qcom,modulator-sel",
 | |
| 			.val_ptr = &cfg->mod_sel,
 | |
| 			.cfg = &wled5_mod_sel_cfg,
 | |
| 		},
 | |
| 		{
 | |
| 			.name = "qcom,cabc-sel",
 | |
| 			.val_ptr = &cfg->cabc_sel,
 | |
| 			.cfg = &wled5_cabc_sel_cfg,
 | |
| 		},
 | |
| 	};
 | |
| 
 | |
| 	const struct wled_bool_opts bool_opts[] = {
 | |
| 		{ "qcom,cs-out", &cfg->cs_out_en, },
 | |
| 		{ "qcom,ext-gen", &cfg->ext_gen, },
 | |
| 		{ "qcom,cabc", &cfg->cabc, },
 | |
| 		{ "qcom,external-pfet", &cfg->external_pfet, },
 | |
| 		{ "qcom,auto-string-detection", &cfg->auto_detection_enabled, },
 | |
| 	};
 | |
| 
 | |
| 	prop_addr = of_get_address(dev->of_node, 0, NULL, NULL);
 | |
| 	if (!prop_addr) {
 | |
| 		dev_err(wled->dev, "invalid IO resources\n");
 | |
| 		return -EINVAL;
 | |
| 	}
 | |
| 	wled->ctrl_addr = be32_to_cpu(*prop_addr);
 | |
| 
 | |
| 	rc = of_property_read_string(dev->of_node, "label", &wled->name);
 | |
| 	if (rc)
 | |
| 		wled->name = devm_kasprintf(dev, GFP_KERNEL, "%pOFn", dev->of_node);
 | |
| 
 | |
| 	switch (wled->version) {
 | |
| 	case 3:
 | |
| 		u32_opts = wled3_opts;
 | |
| 		size = ARRAY_SIZE(wled3_opts);
 | |
| 		*cfg = wled3_config_defaults;
 | |
| 		wled->wled_set_brightness = wled3_set_brightness;
 | |
| 		wled->wled_sync_toggle = wled3_sync_toggle;
 | |
| 		wled->max_string_count = 3;
 | |
| 		wled->sink_addr = wled->ctrl_addr;
 | |
| 		break;
 | |
| 
 | |
| 	case 4:
 | |
| 		u32_opts = wled4_opts;
 | |
| 		size = ARRAY_SIZE(wled4_opts);
 | |
| 		*cfg = wled4_config_defaults;
 | |
| 		wled->wled_set_brightness = wled4_set_brightness;
 | |
| 		wled->wled_sync_toggle = wled3_sync_toggle;
 | |
| 		wled->wled_cabc_config = wled4_cabc_config;
 | |
| 		wled->wled_ovp_delay = wled4_ovp_delay;
 | |
| 		wled->wled_auto_detection_required =
 | |
| 					wled4_auto_detection_required;
 | |
| 		wled->max_string_count = 4;
 | |
| 
 | |
| 		prop_addr = of_get_address(dev->of_node, 1, NULL, NULL);
 | |
| 		if (!prop_addr) {
 | |
| 			dev_err(wled->dev, "invalid IO resources\n");
 | |
| 			return -EINVAL;
 | |
| 		}
 | |
| 		wled->sink_addr = be32_to_cpu(*prop_addr);
 | |
| 		break;
 | |
| 
 | |
| 	case 5:
 | |
| 		u32_opts = wled5_opts;
 | |
| 		size = ARRAY_SIZE(wled5_opts);
 | |
| 		*cfg = wled5_config_defaults;
 | |
| 		wled->wled_set_brightness = wled5_set_brightness;
 | |
| 		wled->wled_sync_toggle = wled3_sync_toggle;
 | |
| 		wled->wled_cabc_config = wled5_cabc_config;
 | |
| 		wled->wled_ovp_delay = wled5_ovp_delay;
 | |
| 		wled->wled_auto_detection_required =
 | |
| 					wled5_auto_detection_required;
 | |
| 		wled->max_string_count = 4;
 | |
| 
 | |
| 		prop_addr = of_get_address(dev->of_node, 1, NULL, NULL);
 | |
| 		if (!prop_addr) {
 | |
| 			dev_err(wled->dev, "invalid IO resources\n");
 | |
| 			return -EINVAL;
 | |
| 		}
 | |
| 		wled->sink_addr = be32_to_cpu(*prop_addr);
 | |
| 		break;
 | |
| 
 | |
| 	default:
 | |
| 		dev_err(wled->dev, "Invalid WLED version\n");
 | |
| 		return -EINVAL;
 | |
| 	}
 | |
| 
 | |
| 	for (i = 0; i < size; ++i) {
 | |
| 		rc = of_property_read_u32(dev->of_node, u32_opts[i].name, &val);
 | |
| 		if (rc == -EINVAL) {
 | |
| 			continue;
 | |
| 		} else if (rc) {
 | |
| 			dev_err(dev, "error reading '%s'\n", u32_opts[i].name);
 | |
| 			return rc;
 | |
| 		}
 | |
| 
 | |
| 		c = UINT_MAX;
 | |
| 		for (j = 0; c != val; j++) {
 | |
| 			c = wled_values(u32_opts[i].cfg, j);
 | |
| 			if (c == UINT_MAX) {
 | |
| 				dev_err(dev, "invalid value for '%s'\n",
 | |
| 					u32_opts[i].name);
 | |
| 				return -EINVAL;
 | |
| 			}
 | |
| 
 | |
| 			if (c == val)
 | |
| 				break;
 | |
| 		}
 | |
| 
 | |
| 		dev_dbg(dev, "'%s' = %u\n", u32_opts[i].name, c);
 | |
| 		*u32_opts[i].val_ptr = j;
 | |
| 	}
 | |
| 
 | |
| 	for (i = 0; i < ARRAY_SIZE(bool_opts); ++i) {
 | |
| 		if (of_property_read_bool(dev->of_node, bool_opts[i].name))
 | |
| 			*bool_opts[i].val_ptr = true;
 | |
| 	}
 | |
| 
 | |
| 	cfg->num_strings = cfg->num_strings + 1;
 | |
| 
 | |
| 	string_len = of_property_count_elems_of_size(dev->of_node,
 | |
| 						     "qcom,enabled-strings",
 | |
| 						     sizeof(u32));
 | |
| 	if (string_len > 0)
 | |
| 		of_property_read_u32_array(dev->of_node,
 | |
| 						"qcom,enabled-strings",
 | |
| 						wled->cfg.enabled_strings,
 | |
| 						sizeof(u32));
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static int wled_configure_short_irq(struct wled *wled,
 | |
| 				    struct platform_device *pdev)
 | |
| {
 | |
| 	int rc;
 | |
| 
 | |
| 	if (!wled->has_short_detect)
 | |
| 		return 0;
 | |
| 
 | |
| 	rc = regmap_update_bits(wled->regmap, wled->ctrl_addr +
 | |
| 				WLED4_CTRL_REG_SHORT_PROTECT,
 | |
| 				WLED4_CTRL_REG_SHORT_EN_MASK,
 | |
| 				WLED4_CTRL_REG_SHORT_EN_MASK);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	wled->short_irq = platform_get_irq_byname(pdev, "short");
 | |
| 	if (wled->short_irq < 0) {
 | |
| 		dev_dbg(&pdev->dev, "short irq is not used\n");
 | |
| 		return 0;
 | |
| 	}
 | |
| 
 | |
| 	rc = devm_request_threaded_irq(wled->dev, wled->short_irq,
 | |
| 				       NULL, wled_short_irq_handler,
 | |
| 				       IRQF_ONESHOT,
 | |
| 				       "wled_short_irq", wled);
 | |
| 	if (rc < 0)
 | |
| 		dev_err(wled->dev, "Unable to request short_irq (err:%d)\n",
 | |
| 			rc);
 | |
| 
 | |
| 	return rc;
 | |
| }
 | |
| 
 | |
| static int wled_configure_ovp_irq(struct wled *wled,
 | |
| 				  struct platform_device *pdev)
 | |
| {
 | |
| 	int rc;
 | |
| 	u32 val;
 | |
| 
 | |
| 	wled->ovp_irq = platform_get_irq_byname(pdev, "ovp");
 | |
| 	if (wled->ovp_irq < 0) {
 | |
| 		dev_dbg(&pdev->dev, "OVP IRQ not found - disabling automatic string detection\n");
 | |
| 		return 0;
 | |
| 	}
 | |
| 
 | |
| 	rc = devm_request_threaded_irq(wled->dev, wled->ovp_irq, NULL,
 | |
| 				       wled_ovp_irq_handler, IRQF_ONESHOT,
 | |
| 				       "wled_ovp_irq", wled);
 | |
| 	if (rc < 0) {
 | |
| 		dev_err(wled->dev, "Unable to request ovp_irq (err:%d)\n",
 | |
| 			rc);
 | |
| 		wled->ovp_irq = 0;
 | |
| 		return 0;
 | |
| 	}
 | |
| 
 | |
| 	rc = regmap_read(wled->regmap, wled->ctrl_addr +
 | |
| 			 WLED3_CTRL_REG_MOD_EN, &val);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	/* Keep OVP irq disabled until module is enabled */
 | |
| 	if (!(val & WLED3_CTRL_REG_MOD_EN_MASK))
 | |
| 		disable_irq(wled->ovp_irq);
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static const struct backlight_ops wled_ops = {
 | |
| 	.update_status = wled_update_status,
 | |
| };
 | |
| 
 | |
| static int wled_probe(struct platform_device *pdev)
 | |
| {
 | |
| 	struct backlight_properties props;
 | |
| 	struct backlight_device *bl;
 | |
| 	struct wled *wled;
 | |
| 	struct regmap *regmap;
 | |
| 	u32 val;
 | |
| 	int rc;
 | |
| 
 | |
| 	regmap = dev_get_regmap(pdev->dev.parent, NULL);
 | |
| 	if (!regmap) {
 | |
| 		dev_err(&pdev->dev, "Unable to get regmap\n");
 | |
| 		return -EINVAL;
 | |
| 	}
 | |
| 
 | |
| 	wled = devm_kzalloc(&pdev->dev, sizeof(*wled), GFP_KERNEL);
 | |
| 	if (!wled)
 | |
| 		return -ENOMEM;
 | |
| 
 | |
| 	wled->regmap = regmap;
 | |
| 	wled->dev = &pdev->dev;
 | |
| 
 | |
| 	wled->version = (uintptr_t)of_device_get_match_data(&pdev->dev);
 | |
| 	if (!wled->version) {
 | |
| 		dev_err(&pdev->dev, "Unknown device version\n");
 | |
| 		return -ENODEV;
 | |
| 	}
 | |
| 
 | |
| 	mutex_init(&wled->lock);
 | |
| 	rc = wled_configure(wled);
 | |
| 	if (rc)
 | |
| 		return rc;
 | |
| 
 | |
| 	val = WLED3_SINK_REG_BRIGHT_MAX;
 | |
| 	of_property_read_u32(pdev->dev.of_node, "max-brightness", &val);
 | |
| 	wled->max_brightness = val;
 | |
| 
 | |
| 	switch (wled->version) {
 | |
| 	case 3:
 | |
| 		wled->cfg.auto_detection_enabled = false;
 | |
| 		rc = wled3_setup(wled);
 | |
| 		if (rc) {
 | |
| 			dev_err(&pdev->dev, "wled3_setup failed\n");
 | |
| 			return rc;
 | |
| 		}
 | |
| 		break;
 | |
| 
 | |
| 	case 4:
 | |
| 		wled->has_short_detect = true;
 | |
| 		rc = wled4_setup(wled);
 | |
| 		if (rc) {
 | |
| 			dev_err(&pdev->dev, "wled4_setup failed\n");
 | |
| 			return rc;
 | |
| 		}
 | |
| 		break;
 | |
| 
 | |
| 	case 5:
 | |
| 		wled->has_short_detect = true;
 | |
| 		if (wled->cfg.cabc_sel)
 | |
| 			wled->max_brightness = WLED5_SINK_REG_BRIGHT_MAX_12B;
 | |
| 
 | |
| 		rc = wled5_setup(wled);
 | |
| 		if (rc) {
 | |
| 			dev_err(&pdev->dev, "wled5_setup failed\n");
 | |
| 			return rc;
 | |
| 		}
 | |
| 		break;
 | |
| 
 | |
| 	default:
 | |
| 		dev_err(wled->dev, "Invalid WLED version\n");
 | |
| 		break;
 | |
| 	}
 | |
| 
 | |
| 	INIT_DELAYED_WORK(&wled->ovp_work, wled_ovp_work);
 | |
| 
 | |
| 	rc = wled_configure_short_irq(wled, pdev);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	rc = wled_configure_ovp_irq(wled, pdev);
 | |
| 	if (rc < 0)
 | |
| 		return rc;
 | |
| 
 | |
| 	val = WLED_DEFAULT_BRIGHTNESS;
 | |
| 	of_property_read_u32(pdev->dev.of_node, "default-brightness", &val);
 | |
| 
 | |
| 	memset(&props, 0, sizeof(struct backlight_properties));
 | |
| 	props.type = BACKLIGHT_RAW;
 | |
| 	props.brightness = val;
 | |
| 	props.max_brightness = wled->max_brightness;
 | |
| 	bl = devm_backlight_device_register(&pdev->dev, wled->name,
 | |
| 					    &pdev->dev, wled,
 | |
| 					    &wled_ops, &props);
 | |
| 	return PTR_ERR_OR_ZERO(bl);
 | |
| };
 | |
| 
 | |
| static int wled_remove(struct platform_device *pdev)
 | |
| {
 | |
| 	struct wled *wled = platform_get_drvdata(pdev);
 | |
| 
 | |
| 	mutex_destroy(&wled->lock);
 | |
| 	cancel_delayed_work_sync(&wled->ovp_work);
 | |
| 	disable_irq(wled->short_irq);
 | |
| 	disable_irq(wled->ovp_irq);
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static const struct of_device_id wled_match_table[] = {
 | |
| 	{ .compatible = "qcom,pm8941-wled", .data = (void *)3 },
 | |
| 	{ .compatible = "qcom,pmi8994-wled", .data = (void *)4 },
 | |
| 	{ .compatible = "qcom,pmi8998-wled", .data = (void *)4 },
 | |
| 	{ .compatible = "qcom,pm660l-wled", .data = (void *)4 },
 | |
| 	{ .compatible = "qcom,pm8150l-wled", .data = (void *)5 },
 | |
| 	{}
 | |
| };
 | |
| MODULE_DEVICE_TABLE(of, wled_match_table);
 | |
| 
 | |
| static struct platform_driver wled_driver = {
 | |
| 	.probe = wled_probe,
 | |
| 	.remove = wled_remove,
 | |
| 	.driver	= {
 | |
| 		.name = "qcom,wled",
 | |
| 		.of_match_table	= wled_match_table,
 | |
| 	},
 | |
| };
 | |
| 
 | |
| module_platform_driver(wled_driver);
 | |
| 
 | |
| MODULE_DESCRIPTION("Qualcomm WLED driver");
 | |
| MODULE_LICENSE("GPL v2");
 |