472 lines
		
	
	
		
			11 KiB
		
	
	
	
		
			C
		
	
	
	
	
	
			
		
		
	
	
			472 lines
		
	
	
		
			11 KiB
		
	
	
	
		
			C
		
	
	
	
	
	
| // SPDX-License-Identifier: GPL-2.0-or-later
 | |
| /*
 | |
|  * GPIO Chip driver for Analog Devices
 | |
|  * ADP5588/ADP5587 I/O Expander and QWERTY Keypad Controller
 | |
|  *
 | |
|  * Copyright 2009-2010 Analog Devices Inc.
 | |
|  */
 | |
| 
 | |
| #include <linux/module.h>
 | |
| #include <linux/kernel.h>
 | |
| #include <linux/slab.h>
 | |
| #include <linux/init.h>
 | |
| #include <linux/i2c.h>
 | |
| #include <linux/gpio/driver.h>
 | |
| #include <linux/interrupt.h>
 | |
| #include <linux/irq.h>
 | |
| #include <linux/of_device.h>
 | |
| 
 | |
| #include <linux/platform_data/adp5588.h>
 | |
| 
 | |
| #define DRV_NAME	"adp5588-gpio"
 | |
| 
 | |
| /*
 | |
|  * Early pre 4.0 Silicon required to delay readout by at least 25ms,
 | |
|  * since the Event Counter Register updated 25ms after the interrupt
 | |
|  * asserted.
 | |
|  */
 | |
| #define WA_DELAYED_READOUT_REVID(rev)	((rev) < 4)
 | |
| 
 | |
| struct adp5588_gpio {
 | |
| 	struct i2c_client *client;
 | |
| 	struct gpio_chip gpio_chip;
 | |
| 	struct mutex lock;	/* protect cached dir, dat_out */
 | |
| 	/* protect serialized access to the interrupt controller bus */
 | |
| 	struct mutex irq_lock;
 | |
| 	uint8_t dat_out[3];
 | |
| 	uint8_t dir[3];
 | |
| 	uint8_t int_lvl_low[3];
 | |
| 	uint8_t int_lvl_high[3];
 | |
| 	uint8_t int_en[3];
 | |
| 	uint8_t irq_mask[3];
 | |
| 	uint8_t int_input_en[3];
 | |
| };
 | |
| 
 | |
| static int adp5588_gpio_read(struct i2c_client *client, u8 reg)
 | |
| {
 | |
| 	int ret = i2c_smbus_read_byte_data(client, reg);
 | |
| 
 | |
| 	if (ret < 0)
 | |
| 		dev_err(&client->dev, "Read Error\n");
 | |
| 
 | |
| 	return ret;
 | |
| }
 | |
| 
 | |
| static int adp5588_gpio_write(struct i2c_client *client, u8 reg, u8 val)
 | |
| {
 | |
| 	int ret = i2c_smbus_write_byte_data(client, reg, val);
 | |
| 
 | |
| 	if (ret < 0)
 | |
| 		dev_err(&client->dev, "Write Error\n");
 | |
| 
 | |
| 	return ret;
 | |
| }
 | |
| 
 | |
| static int adp5588_gpio_get_value(struct gpio_chip *chip, unsigned off)
 | |
| {
 | |
| 	struct adp5588_gpio *dev = gpiochip_get_data(chip);
 | |
| 	unsigned bank = ADP5588_BANK(off);
 | |
| 	unsigned bit = ADP5588_BIT(off);
 | |
| 	int val;
 | |
| 
 | |
| 	mutex_lock(&dev->lock);
 | |
| 
 | |
| 	if (dev->dir[bank] & bit)
 | |
| 		val = dev->dat_out[bank];
 | |
| 	else
 | |
| 		val = adp5588_gpio_read(dev->client, GPIO_DAT_STAT1 + bank);
 | |
| 
 | |
| 	mutex_unlock(&dev->lock);
 | |
| 
 | |
| 	return !!(val & bit);
 | |
| }
 | |
| 
 | |
| static void adp5588_gpio_set_value(struct gpio_chip *chip,
 | |
| 				   unsigned off, int val)
 | |
| {
 | |
| 	unsigned bank, bit;
 | |
| 	struct adp5588_gpio *dev = gpiochip_get_data(chip);
 | |
| 
 | |
| 	bank = ADP5588_BANK(off);
 | |
| 	bit = ADP5588_BIT(off);
 | |
| 
 | |
| 	mutex_lock(&dev->lock);
 | |
| 	if (val)
 | |
| 		dev->dat_out[bank] |= bit;
 | |
| 	else
 | |
| 		dev->dat_out[bank] &= ~bit;
 | |
| 
 | |
| 	adp5588_gpio_write(dev->client, GPIO_DAT_OUT1 + bank,
 | |
| 			   dev->dat_out[bank]);
 | |
| 	mutex_unlock(&dev->lock);
 | |
| }
 | |
| 
 | |
| static int adp5588_gpio_direction_input(struct gpio_chip *chip, unsigned off)
 | |
| {
 | |
| 	int ret;
 | |
| 	unsigned bank;
 | |
| 	struct adp5588_gpio *dev = gpiochip_get_data(chip);
 | |
| 
 | |
| 	bank = ADP5588_BANK(off);
 | |
| 
 | |
| 	mutex_lock(&dev->lock);
 | |
| 	dev->dir[bank] &= ~ADP5588_BIT(off);
 | |
| 	ret = adp5588_gpio_write(dev->client, GPIO_DIR1 + bank, dev->dir[bank]);
 | |
| 	mutex_unlock(&dev->lock);
 | |
| 
 | |
| 	return ret;
 | |
| }
 | |
| 
 | |
| static int adp5588_gpio_direction_output(struct gpio_chip *chip,
 | |
| 					 unsigned off, int val)
 | |
| {
 | |
| 	int ret;
 | |
| 	unsigned bank, bit;
 | |
| 	struct adp5588_gpio *dev = gpiochip_get_data(chip);
 | |
| 
 | |
| 	bank = ADP5588_BANK(off);
 | |
| 	bit = ADP5588_BIT(off);
 | |
| 
 | |
| 	mutex_lock(&dev->lock);
 | |
| 	dev->dir[bank] |= bit;
 | |
| 
 | |
| 	if (val)
 | |
| 		dev->dat_out[bank] |= bit;
 | |
| 	else
 | |
| 		dev->dat_out[bank] &= ~bit;
 | |
| 
 | |
| 	ret = adp5588_gpio_write(dev->client, GPIO_DAT_OUT1 + bank,
 | |
| 				 dev->dat_out[bank]);
 | |
| 	ret |= adp5588_gpio_write(dev->client, GPIO_DIR1 + bank,
 | |
| 				 dev->dir[bank]);
 | |
| 	mutex_unlock(&dev->lock);
 | |
| 
 | |
| 	return ret;
 | |
| }
 | |
| 
 | |
| #ifdef CONFIG_GPIO_ADP5588_IRQ
 | |
| 
 | |
| static void adp5588_irq_bus_lock(struct irq_data *d)
 | |
| {
 | |
| 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
 | |
| 	struct adp5588_gpio *dev = gpiochip_get_data(gc);
 | |
| 
 | |
| 	mutex_lock(&dev->irq_lock);
 | |
| }
 | |
| 
 | |
|  /*
 | |
|   * genirq core code can issue chip->mask/unmask from atomic context.
 | |
|   * This doesn't work for slow busses where an access needs to sleep.
 | |
|   * bus_sync_unlock() is therefore called outside the atomic context,
 | |
|   * syncs the current irq mask state with the slow external controller
 | |
|   * and unlocks the bus.
 | |
|   */
 | |
| 
 | |
| static void adp5588_irq_bus_sync_unlock(struct irq_data *d)
 | |
| {
 | |
| 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
 | |
| 	struct adp5588_gpio *dev = gpiochip_get_data(gc);
 | |
| 	int i;
 | |
| 
 | |
| 	for (i = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) {
 | |
| 		if (dev->int_input_en[i]) {
 | |
| 			mutex_lock(&dev->lock);
 | |
| 			dev->dir[i] &= ~dev->int_input_en[i];
 | |
| 			dev->int_input_en[i] = 0;
 | |
| 			adp5588_gpio_write(dev->client, GPIO_DIR1 + i,
 | |
| 					   dev->dir[i]);
 | |
| 			mutex_unlock(&dev->lock);
 | |
| 		}
 | |
| 
 | |
| 		if (dev->int_en[i] ^ dev->irq_mask[i]) {
 | |
| 			dev->int_en[i] = dev->irq_mask[i];
 | |
| 			adp5588_gpio_write(dev->client, GPI_EM1 + i,
 | |
| 					   dev->int_en[i]);
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	mutex_unlock(&dev->irq_lock);
 | |
| }
 | |
| 
 | |
| static void adp5588_irq_mask(struct irq_data *d)
 | |
| {
 | |
| 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
 | |
| 	struct adp5588_gpio *dev = gpiochip_get_data(gc);
 | |
| 
 | |
| 	dev->irq_mask[ADP5588_BANK(d->hwirq)] &= ~ADP5588_BIT(d->hwirq);
 | |
| }
 | |
| 
 | |
| static void adp5588_irq_unmask(struct irq_data *d)
 | |
| {
 | |
| 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
 | |
| 	struct adp5588_gpio *dev = gpiochip_get_data(gc);
 | |
| 
 | |
| 	dev->irq_mask[ADP5588_BANK(d->hwirq)] |= ADP5588_BIT(d->hwirq);
 | |
| }
 | |
| 
 | |
| static int adp5588_irq_set_type(struct irq_data *d, unsigned int type)
 | |
| {
 | |
| 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
 | |
| 	struct adp5588_gpio *dev = gpiochip_get_data(gc);
 | |
| 	uint16_t gpio = d->hwirq;
 | |
| 	unsigned bank, bit;
 | |
| 
 | |
| 	bank = ADP5588_BANK(gpio);
 | |
| 	bit = ADP5588_BIT(gpio);
 | |
| 
 | |
| 	dev->int_lvl_low[bank] &= ~bit;
 | |
| 	dev->int_lvl_high[bank] &= ~bit;
 | |
| 
 | |
| 	if (type & IRQ_TYPE_EDGE_BOTH || type & IRQ_TYPE_LEVEL_HIGH)
 | |
| 		dev->int_lvl_high[bank] |= bit;
 | |
| 
 | |
| 	if (type & IRQ_TYPE_EDGE_BOTH || type & IRQ_TYPE_LEVEL_LOW)
 | |
| 		dev->int_lvl_low[bank] |= bit;
 | |
| 
 | |
| 	dev->int_input_en[bank] |= bit;
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static struct irq_chip adp5588_irq_chip = {
 | |
| 	.name			= "adp5588",
 | |
| 	.irq_mask		= adp5588_irq_mask,
 | |
| 	.irq_unmask		= adp5588_irq_unmask,
 | |
| 	.irq_bus_lock		= adp5588_irq_bus_lock,
 | |
| 	.irq_bus_sync_unlock	= adp5588_irq_bus_sync_unlock,
 | |
| 	.irq_set_type		= adp5588_irq_set_type,
 | |
| };
 | |
| 
 | |
| static irqreturn_t adp5588_irq_handler(int irq, void *devid)
 | |
| {
 | |
| 	struct adp5588_gpio *dev = devid;
 | |
| 	int status = adp5588_gpio_read(dev->client, INT_STAT);
 | |
| 
 | |
| 	if (status & ADP5588_KE_INT) {
 | |
| 		int ev_cnt = adp5588_gpio_read(dev->client, KEY_LCK_EC_STAT);
 | |
| 
 | |
| 		if (ev_cnt > 0) {
 | |
| 			int i;
 | |
| 
 | |
| 			for (i = 0; i < (ev_cnt & ADP5588_KEC); i++) {
 | |
| 				int key = adp5588_gpio_read(dev->client,
 | |
| 							    Key_EVENTA + i);
 | |
| 				/* GPIN events begin at 97,
 | |
| 				 * bit 7 indicates logic level
 | |
| 				 */
 | |
| 				int gpio = (key & 0x7f) - 97;
 | |
| 				int lvl = key & (1 << 7);
 | |
| 				int bank = ADP5588_BANK(gpio);
 | |
| 				int bit = ADP5588_BIT(gpio);
 | |
| 
 | |
| 				if ((lvl && dev->int_lvl_high[bank] & bit) ||
 | |
| 				    (!lvl && dev->int_lvl_low[bank] & bit))
 | |
| 					handle_nested_irq(irq_find_mapping(
 | |
| 					      dev->gpio_chip.irq.domain, gpio));
 | |
| 			}
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	adp5588_gpio_write(dev->client, INT_STAT, status); /* Status is W1C */
 | |
| 
 | |
| 	return IRQ_HANDLED;
 | |
| }
 | |
| 
 | |
| 
 | |
| static int adp5588_irq_init_hw(struct gpio_chip *gc)
 | |
| {
 | |
| 	struct adp5588_gpio *dev = gpiochip_get_data(gc);
 | |
| 	/* Enable IRQs after registering chip */
 | |
| 	adp5588_gpio_write(dev->client, CFG,
 | |
| 			   ADP5588_AUTO_INC | ADP5588_INT_CFG | ADP5588_KE_IEN);
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static int adp5588_irq_setup(struct adp5588_gpio *dev)
 | |
| {
 | |
| 	struct i2c_client *client = dev->client;
 | |
| 	int ret;
 | |
| 	struct adp5588_gpio_platform_data *pdata =
 | |
| 			dev_get_platdata(&client->dev);
 | |
| 	struct gpio_irq_chip *girq;
 | |
| 
 | |
| 	adp5588_gpio_write(client, CFG, ADP5588_AUTO_INC);
 | |
| 	adp5588_gpio_write(client, INT_STAT, -1); /* status is W1C */
 | |
| 
 | |
| 	mutex_init(&dev->irq_lock);
 | |
| 
 | |
| 	ret = devm_request_threaded_irq(&client->dev, client->irq,
 | |
| 					NULL, adp5588_irq_handler, IRQF_ONESHOT
 | |
| 					| IRQF_TRIGGER_FALLING | IRQF_SHARED,
 | |
| 					dev_name(&client->dev), dev);
 | |
| 	if (ret) {
 | |
| 		dev_err(&client->dev, "failed to request irq %d\n",
 | |
| 			client->irq);
 | |
| 		return ret;
 | |
| 	}
 | |
| 
 | |
| 	/* This will be registered in the call to devm_gpiochip_add_data() */
 | |
| 	girq = &dev->gpio_chip.irq;
 | |
| 	girq->chip = &adp5588_irq_chip;
 | |
| 	/* This will let us handle the parent IRQ in the driver */
 | |
| 	girq->parent_handler = NULL;
 | |
| 	girq->num_parents = 0;
 | |
| 	girq->parents = NULL;
 | |
| 	girq->first = pdata ? pdata->irq_base : 0;
 | |
| 	girq->default_type = IRQ_TYPE_NONE;
 | |
| 	girq->handler = handle_simple_irq;
 | |
| 	girq->init_hw = adp5588_irq_init_hw;
 | |
| 	girq->threaded = true;
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| #else
 | |
| static int adp5588_irq_setup(struct adp5588_gpio *dev)
 | |
| {
 | |
| 	struct i2c_client *client = dev->client;
 | |
| 	dev_warn(&client->dev, "interrupt support not compiled in\n");
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| #endif /* CONFIG_GPIO_ADP5588_IRQ */
 | |
| 
 | |
| static int adp5588_gpio_probe(struct i2c_client *client)
 | |
| {
 | |
| 	struct adp5588_gpio_platform_data *pdata =
 | |
| 			dev_get_platdata(&client->dev);
 | |
| 	struct adp5588_gpio *dev;
 | |
| 	struct gpio_chip *gc;
 | |
| 	int ret, i, revid;
 | |
| 	unsigned int pullup_dis_mask = 0;
 | |
| 
 | |
| 	if (!i2c_check_functionality(client->adapter,
 | |
| 					I2C_FUNC_SMBUS_BYTE_DATA)) {
 | |
| 		dev_err(&client->dev, "SMBUS Byte Data not Supported\n");
 | |
| 		return -EIO;
 | |
| 	}
 | |
| 
 | |
| 	dev = devm_kzalloc(&client->dev, sizeof(*dev), GFP_KERNEL);
 | |
| 	if (!dev)
 | |
| 		return -ENOMEM;
 | |
| 
 | |
| 	dev->client = client;
 | |
| 
 | |
| 	gc = &dev->gpio_chip;
 | |
| 	gc->direction_input = adp5588_gpio_direction_input;
 | |
| 	gc->direction_output = adp5588_gpio_direction_output;
 | |
| 	gc->get = adp5588_gpio_get_value;
 | |
| 	gc->set = adp5588_gpio_set_value;
 | |
| 	gc->can_sleep = true;
 | |
| 	gc->base = -1;
 | |
| 	gc->parent = &client->dev;
 | |
| 
 | |
| 	if (pdata) {
 | |
| 		gc->base = pdata->gpio_start;
 | |
| 		gc->names = pdata->names;
 | |
| 		pullup_dis_mask = pdata->pullup_dis_mask;
 | |
| 	}
 | |
| 
 | |
| 	gc->ngpio = ADP5588_MAXGPIO;
 | |
| 	gc->label = client->name;
 | |
| 	gc->owner = THIS_MODULE;
 | |
| 
 | |
| 	mutex_init(&dev->lock);
 | |
| 
 | |
| 	ret = adp5588_gpio_read(dev->client, DEV_ID);
 | |
| 	if (ret < 0)
 | |
| 		return ret;
 | |
| 
 | |
| 	revid = ret & ADP5588_DEVICE_ID_MASK;
 | |
| 
 | |
| 	for (i = 0, ret = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) {
 | |
| 		dev->dat_out[i] = adp5588_gpio_read(client, GPIO_DAT_OUT1 + i);
 | |
| 		dev->dir[i] = adp5588_gpio_read(client, GPIO_DIR1 + i);
 | |
| 		ret |= adp5588_gpio_write(client, KP_GPIO1 + i, 0);
 | |
| 		ret |= adp5588_gpio_write(client, GPIO_PULL1 + i,
 | |
| 				(pullup_dis_mask >> (8 * i)) & 0xFF);
 | |
| 		ret |= adp5588_gpio_write(client, GPIO_INT_EN1 + i, 0);
 | |
| 		if (ret)
 | |
| 			return ret;
 | |
| 	}
 | |
| 
 | |
| 	if (client->irq) {
 | |
| 		if (WA_DELAYED_READOUT_REVID(revid)) {
 | |
| 			dev_warn(&client->dev, "GPIO int not supported\n");
 | |
| 		} else {
 | |
| 			ret = adp5588_irq_setup(dev);
 | |
| 			if (ret)
 | |
| 				return ret;
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	ret = devm_gpiochip_add_data(&client->dev, &dev->gpio_chip, dev);
 | |
| 	if (ret)
 | |
| 		return ret;
 | |
| 
 | |
| 	if (pdata && pdata->setup) {
 | |
| 		ret = pdata->setup(client, gc->base, gc->ngpio, pdata->context);
 | |
| 		if (ret < 0)
 | |
| 			dev_warn(&client->dev, "setup failed, %d\n", ret);
 | |
| 	}
 | |
| 
 | |
| 	i2c_set_clientdata(client, dev);
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static int adp5588_gpio_remove(struct i2c_client *client)
 | |
| {
 | |
| 	struct adp5588_gpio_platform_data *pdata =
 | |
| 			dev_get_platdata(&client->dev);
 | |
| 	struct adp5588_gpio *dev = i2c_get_clientdata(client);
 | |
| 	int ret;
 | |
| 
 | |
| 	if (pdata && pdata->teardown) {
 | |
| 		ret = pdata->teardown(client,
 | |
| 				      dev->gpio_chip.base, dev->gpio_chip.ngpio,
 | |
| 				      pdata->context);
 | |
| 		if (ret < 0) {
 | |
| 			dev_err(&client->dev, "teardown failed %d\n", ret);
 | |
| 			return ret;
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	if (dev->client->irq)
 | |
| 		free_irq(dev->client->irq, dev);
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static const struct i2c_device_id adp5588_gpio_id[] = {
 | |
| 	{DRV_NAME, 0},
 | |
| 	{}
 | |
| };
 | |
| MODULE_DEVICE_TABLE(i2c, adp5588_gpio_id);
 | |
| 
 | |
| #ifdef CONFIG_OF
 | |
| static const struct of_device_id adp5588_gpio_of_id[] = {
 | |
| 	{ .compatible = "adi," DRV_NAME, },
 | |
| 	{},
 | |
| };
 | |
| MODULE_DEVICE_TABLE(of, adp5588_gpio_of_id);
 | |
| #endif
 | |
| 
 | |
| static struct i2c_driver adp5588_gpio_driver = {
 | |
| 	.driver = {
 | |
| 		.name = DRV_NAME,
 | |
| 		.of_match_table = of_match_ptr(adp5588_gpio_of_id),
 | |
| 	},
 | |
| 	.probe_new = adp5588_gpio_probe,
 | |
| 	.remove = adp5588_gpio_remove,
 | |
| 	.id_table = adp5588_gpio_id,
 | |
| };
 | |
| 
 | |
| module_i2c_driver(adp5588_gpio_driver);
 | |
| 
 | |
| MODULE_AUTHOR("Michael Hennerich <michael.hennerich@analog.com>");
 | |
| MODULE_DESCRIPTION("GPIO ADP5588 Driver");
 | |
| MODULE_LICENSE("GPL");
 |